From 718e3744195351130f4ce7dbe0613f4b3e23df93 Mon Sep 17 00:00:00 2001
From: paul <paul>
Date: Fri, 13 Dec 2002 20:15:29 +0000
Subject: Initial revision

---
 doc/ripngd.texi | 85 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)
 create mode 100644 doc/ripngd.texi

(limited to 'doc/ripngd.texi')

diff --git a/doc/ripngd.texi b/doc/ripngd.texi
new file mode 100644
index 00000000..b49f0bf3
--- /dev/null
+++ b/doc/ripngd.texi
@@ -0,0 +1,85 @@
+@node RIPng, OSPFv2, RIP, Top
+@comment  node-name,  next,  previous,  up
+@chapter RIPng
+
+@command{ripngd} supports the RIPng protocol as described in RFC2080.  It's an
+IPv6 reincarnation of the RIP protocol.
+
+@menu
+* Invoking ripngd::             
+* ripngd Configuration::        
+* ripngd Terminal Mode Commands::  
+* ripngd Filtering Commands::   
+@end menu
+
+@node Invoking ripngd, ripngd Configuration, RIPng, RIPng
+@comment  node-name,  next,  previous,  up
+@section Invoking ripngd
+
+There are no @code{ripngd} specific invocation options.  Common options
+can be specified (@pxref{Common Invocation Options}).
+
+@node ripngd Configuration, ripngd Terminal Mode Commands, Invoking ripngd, RIPng
+@comment  node-name,  next,  previous,  up
+@section ripngd Configuration
+
+Currently ripngd supports the following commands:
+
+@deffn Command {router ripng} {}
+Enable RIPng.
+@end deffn
+
+@deffn {RIPng Command} {flush_timer @var{time}} {}
+Set flush timer.
+@end deffn
+
+@deffn {RIPng Command} {network @var{network}} {}
+Set RIPng enabled interface by @var{network}
+@end deffn
+
+@deffn {RIPng Command} {network @var{ifname}} {}
+Set RIPng enabled interface by @var{ifname}
+@end deffn
+
+@deffn {RIPng Command} {route @var{network}} {}
+Set RIPng static routing announcement of @var{network}.
+@end deffn
+
+@deffn Command {router zebra} {}
+This command is the default and does not appear in the configuration.
+With this statement, RIPng routes go to the @command{zebra} daemon.
+@end deffn
+
+@node ripngd Terminal Mode Commands, ripngd Filtering Commands, ripngd Configuration, RIPng
+@comment  node-name,  next,  previous,  up
+@section ripngd Terminal Mode Commands
+
+@deffn Command {show ip ripng} {}
+@end deffn
+
+@deffn Command {show debugging ripng} {}
+@end deffn
+
+@deffn Command {debug ripng events} {}
+@end deffn
+
+@deffn Command {debug ripng packet} {}
+@end deffn
+
+@deffn Command {debug ripng zebra} {}
+@end deffn
+
+@node ripngd Filtering Commands,  , ripngd Terminal Mode Commands, RIPng
+@comment  node-name,  next,  previous,  up
+@section ripngd Filtering Commands
+
+@deffn Command {distribute-list @var{access_list} (in|out) @var{ifname}} {}
+You can apply an access-list to the interface using the
+@code{distribute-list} command.  @var{access_list} is an access-list
+name.  @var{direct} is @samp{in} or @samp{out}.  If @var{direct} is
+@samp{in}, the access-list is applied only to incoming packets.
+
+@example
+distribute-list local-only out sit1
+@end example
+@end deffn
-- 
cgit v1.2.1