From 2c00d1580fcfac3d3719f83f660f63e7e8523120 Mon Sep 17 00:00:00 2001
From: Greg Dahlman <gdahlman@hotmail.com>
Date: Mon, 5 Dec 2011 20:34:02 -0800
Subject: Fixing issues in pins.h and fastio.h, I created them not
 understanding it was using arduino pin numbers

I also put in a note that Gen 7 only works at 16 MHZ due to timing issues with WProgram.h and wiring.h
---
 Sprinter/pins.h | 47 ++++++++++++++++++++++++-----------------------
 1 file changed, 24 insertions(+), 23 deletions(-)

(limited to 'Sprinter/pins.h')

diff --git a/Sprinter/pins.h b/Sprinter/pins.h
index 01f29ed..63719f4 100644
--- a/Sprinter/pins.h
+++ b/Sprinter/pins.h
@@ -686,6 +686,7 @@
 
 #endif
 
+
 /****************************************************************************************
 * Gen7 pin assignment
 *
@@ -693,46 +694,46 @@
 #if MOTHERBOARD == 7
 #define KNOWN_BOARD 1
 
-#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) && !defined(__AVR_ATmega644__) 
+#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) 
     #error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
 #endif
 
 //x axis pins
-    #define X_STEP_PIN      15
+    #define X_STEP_PIN      19
     #define X_DIR_PIN       18
-    #define X_ENABLE_PIN    33
-    #define X_MIN_PIN       8
-    #define X_MAX_PIN       7
+    #define X_ENABLE_PIN    -1
+    #define X_MIN_PIN       7
+    #define X_MAX_PIN       6
 
     //y axis pins
-    #define Y_STEP_PIN      29
-    #define Y_DIR_PIN       28
-    #define Y_ENABLE_PIN    33
-    #define Y_MIN_PIN       3
-    #define Y_MAX_PIN       6
+    #define Y_STEP_PIN      23
+    #define Y_DIR_PIN       22
+    #define Y_ENABLE_PIN    -1
+    #define Y_MIN_PIN       5
+    #define Y_MAX_PIN       2
 
     //z axis pins
-    #define Z_STEP_PIN      35
-    #define Z_DIR_PIN       34
-    #define Z_ENABLE_PIN    33
-    #define Z_MIN_PIN       2
-    #define Z_MAX_PIN       1
+    #define Z_STEP_PIN      26
+    #define Z_DIR_PIN       25
+    #define Z_ENABLE_PIN    24
+    #define Z_MIN_PIN       1
+    #define Z_MAX_PIN       0
 
     //extruder pins
-    #define E_STEP_PIN      37     
-    #define E_DIR_PIN       36     
-    #define E_ENABLE_PIN    33     
-    #define TEMP_0_PIN      39    // Extruder 
-    #define HEATER_0_PIN     5    // Extruder
-    #define HEATER_1_PIN     4    // Bed
+    #define E_STEP_PIN      28     
+    #define E_DIR_PIN       27     
+    #define E_ENABLE_PIN    -1     
+    #define TEMP_0_PIN      1    // Extruder 
+    #define HEATER_0_PIN     4    // Extruder
+    #define HEATER_1_PIN     3    // Bed
 
 
     #define SDPOWER         -1
     #define SDSS            -1
     #define LED_PIN         -1    
-    #define TEMP_1_PIN      38    //Bed   
+    #define TEMP_1_PIN      2    //Bed   
     #define FAN_PIN         -1    
-    #define PS_ON_PIN       21    
+    #define PS_ON_PIN       15    
 
 #endif
 
-- 
cgit v1.2.1