From e4af5e82f26fab59bb2bda540e1673317f48ce8a Mon Sep 17 00:00:00 2001 From: kliment Date: Mon, 4 Jul 2011 16:17:19 +0200 Subject: Rename to Sprinter --- Tonokip_Firmware/configuration.h | 158 --------------------------------------- 1 file changed, 158 deletions(-) delete mode 100644 Tonokip_Firmware/configuration.h (limited to 'Tonokip_Firmware/configuration.h') diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h deleted file mode 100644 index 0a38a6a..0000000 --- a/Tonokip_Firmware/configuration.h +++ /dev/null @@ -1,158 +0,0 @@ -#ifndef PARAMETERS_H -#define PARAMETERS_H - -// NO RS485/EXTRUDER CONTROLLER SUPPORT -// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!! -#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5, Sanguinololu = 6 - -//Comment out to disable SD support -#define SDSUPPORT 1 - -//Min step delay in microseconds. If you are experiencing missing steps, try to raise the delay microseconds, but be aware this -// If you enable this, make sure STEP_DELAY_RATIO is disabled. -//#define STEP_DELAY_MICROS 1 - -//Step delay over interval ratio. If you are still experiencing missing steps, try to uncomment the following line, but be aware this -//If you enable this, make sure STEP_DELAY_MICROS is disabled. -//#define STEP_DELAY_RATIO 0.25 - -//Comment this to disable ramp acceleration -#define RAMP_ACCELERATION 1 - -//Acceleration settings -#ifdef RAMP_ACCELERATION -//X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. -float max_start_speed_units_per_second[] = {25.0,25.0,0.2,10.0}; -long max_acceleration_units_per_sq_second[] = {1000,1000,50,10000}; // X, Y, Z and E max acceleration in mm/s^2 for printing moves or retracts -long max_travel_acceleration_units_per_sq_second[] = {500,500,50}; // X, Y, Z max acceleration in mm/s^2 for travel moves -#endif - -// AD595 THERMOCOUPLE SUPPORT UNTESTED... USE WITH CAUTION!!!! - -//PID settings: -//Uncomment the following line to enable PID support. This is untested and could be disastrous. Be careful. -//#define PIDTEMP 1 -#ifdef PIDTEMP -#define PID_MAX 255 // limits current to nozzle -#define PID_INTEGRAL_DRIVE_MAX 220 -#define PID_PGAIN 180 //100 is 1.0 -#define PID_IGAIN 2 //100 is 1.0 -#define PID_DGAIN 100 //100 is 1.0 -#endif - -//How often should the heater check for new temp readings, in milliseconds -#define HEATER_CHECK_INTERVAL 500 -#define BED_CHECK_INTERVAL 5000 -//Comment the following line to enable heat management during acceleration -#define DISABLE_CHECK_DURING_ACC -#ifndef DISABLE_CHECK_DURING_ACC - //Uncomment the following line to disable heat management during the move - //#define DISABLE_CHECK_DURING_MOVE -#endif -//Uncomment the following line to disable heat management during travel moves (and extruder-only moves, eg: retracts), strongly recommended if you are missing steps mid print. -//Probably this should remain commented if are using PID. -//It also defines the max milliseconds interval after which a travel move is not considered so for the sake of this feature. -#define DISABLE_CHECK_DURING_TRAVEL 1000 - -//Experimental temperature smoothing - only uncomment this if your temp readings are noisy -//#define SMOOTHING 1 -//#define SMOOTHFACTOR 16 //best to use a power of two here - determines how many values are averaged together by the smoothing algorithm - -//Experimental watchdog and minimal temp -//The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature -//If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109 -//#define WATCHPERIOD 5000 //5 seconds -//The minimal temperature defines the temperature below which the heater will not be enabled -//#define MINTEMP - -//Experimental max temp -//When temperature exceeds max temp, your bot will halt. -//This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! -//You should use MINTEMP for thermistor short/failure protection. -//#define MAXTEMP 275 - -// Select one of these only to define how the nozzle temp is read. -#define HEATER_USES_THERMISTOR -//#define HEATER_USES_AD595 -//#define HEATER_USES_MAX6675 - -// Select one of these only to define how the bed temp is read. -#define BED_USES_THERMISTOR -//#define BED_USES_AD595 - -// Calibration formulas -// e_extruded_steps_per_mm = e_feedstock_steps_per_mm * (desired_extrusion_diameter^2 / feedstock_diameter^2) -// new_axis_steps_per_mm = previous_axis_steps_per_mm * (test_distance_instructed/test_distance_traveled) -// units are in millimeters or whatever length unit you prefer: inches,football-fields,parsecs etc - -//Calibration variables -const int NUM_AXIS = 4; // The axis order in all axis related arrays is X, Y, Z, E -bool axis_relative_modes[] = {false, false, false, false}; -float axis_steps_per_unit[] = {80.376,80.376,3200/1.25,16}; // {X steps per unit, Y steps per unit, Z steps per unit, E steps per unit} -//For SAE Prusa mendeel float z_steps_per_unit = should be 3200/1.411 for 5/16-18 rod and 3200/1.058 for 5/16-24 -//float axis_steps_per_unit[] = {10.047,10.047,833.398,0.706}; -float max_feedrate[] = {200000, 200000, 240, 500000}; //mmm, acceleration! - -//For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 -const bool X_ENABLE_ON = 0; -const bool Y_ENABLE_ON = 0; -const bool Z_ENABLE_ON = 0; -const bool E_ENABLE_ON = 0; - -//Disables axis when it's not being used. -const bool DISABLE_X = false; -const bool DISABLE_Y = false; -const bool DISABLE_Z = true; -const bool DISABLE_E = false; - -const bool INVERT_X_DIR = false; -const bool INVERT_Y_DIR = false; -const bool INVERT_Z_DIR = true; -const bool INVERT_E_DIR = false; - -// Sets direction of endstops when homing; 1=MAX, -1=MIN -const int X_HOME_DIR = -1; -const int Y_HOME_DIR = -1; -const int Z_HOME_DIR = -1; - - -//Thermistor settings: - -//Uncomment for 100k thermistor -//#include "ThermistorTable_100k.h" -//#include "BedThermistorTable_100k.h" - -//Uncomment for 200k thermistor -//#include "ThermistorTable_200k.h" -//#include "BedThermistorTable_200k.h" - -//Identical thermistors on heater and bed - use this if you have no heated bed or if the thermistors are the same on both: -#include "ThermistorTable_200k.h" -//#include "ThermistorTable_100k.h" -//#include "ThermistorTable_mendelparts.h" -#define BNUMTEMPS NUMTEMPS -#define bedtemptable temptable - -//Endstop Settings -#define ENDSTOPPULLUPS 1 -const bool ENDSTOPS_INVERTING = false; -const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero. -const bool max_software_endstops = true; //If true, axis won't move to coordinates greater than the defined lengths below. -const int X_MAX_LENGTH = 220; -const int Y_MAX_LENGTH = 220; -const int Z_MAX_LENGTH = 100; - -#define BAUDRATE 115200 - -//Uncomment the following line to enable debugging. You can better control debugging below the following line -//#define DEBUG -#ifdef DEBUG - //#define DEBUG_PREPARE_MOVE //Enable this to debug prepare_move() function - //#define DEBUG_BRESENHAM //Enable this to debug the Bresenham algorithm - //#define DEBUG_RAMP_ACCELERATION //Enable this to debug all constant acceleration info - //#define DEBUG_MOVE_TIME //Enable this to time each move and print the result - //#define DEBUG_HEAT_MGMT //Enable this to debug heat management. WARNING, this will cause axes to jitter! - //#define DEBUG_DISABLE_CHECK_DURING_TRAVEL //Debug the namesake feature, see above in this file -#endif - -#endif -- cgit v1.2.1