From e4af5e82f26fab59bb2bda540e1673317f48ce8a Mon Sep 17 00:00:00 2001 From: kliment Date: Mon, 4 Jul 2011 16:17:19 +0200 Subject: Rename to Sprinter --- Tonokip_Firmware/pins.h | 477 ------------------------------------------------ 1 file changed, 477 deletions(-) delete mode 100644 Tonokip_Firmware/pins.h (limited to 'Tonokip_Firmware/pins.h') diff --git a/Tonokip_Firmware/pins.h b/Tonokip_Firmware/pins.h deleted file mode 100644 index eee78e8..0000000 --- a/Tonokip_Firmware/pins.h +++ /dev/null @@ -1,477 +0,0 @@ -#ifndef PINS_H -#define PINS_H - -/**************************************************************************************** -* Arduino pin assignment -* -* ATMega168 -* +-\/-+ -* PC6 1| |28 PC5 (AI 5 / D19) -* (D 0) PD0 2| |27 PC4 (AI 4 / D18) -* (D 1) PD1 3| |26 PC3 (AI 3 / D17) -* (D 2) PD2 4| |25 PC2 (AI 2 / D16) -* PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15) -* (D 4) PD4 6| |23 PC0 (AI 0 / D14) -* VCC 7| |22 GND -* GND 8| |21 AREF -* PB6 9| |20 AVCC -* PB7 10| |19 PB5 (D 13) -* PWM+ (D 5) PD5 11| |18 PB4 (D 12) -* PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM -* (D 7) PD7 13| |16 PB2 (D 10) PWM -* (D 8) PB0 14| |15 PB1 (D 9) PWM -* +----+ -****************************************************************************************/ -#if MOTHERBOARD == 0 -#ifndef __AVR_ATmega168__ -#error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu. -#endif - -#define X_STEP_PIN 2 -#define X_DIR_PIN 3 -#define X_ENABLE_PIN -1 -#define X_MIN_PIN 4 -#define X_MAX_PIN 9 - -#define Y_STEP_PIN 10 -#define Y_DIR_PIN 7 -#define Y_ENABLE_PIN -1 -#define Y_MIN_PIN 8 -#define Y_MAX_PIN 13 - -#define Z_STEP_PIN 19 -#define Z_DIR_PIN 18 -#define Z_ENABLE_PIN 5 -#define Z_MIN_PIN 17 -#define Z_MAX_PIN 16 - -#define E_STEP_PIN 11 -#define E_DIR_PIN 12 -#define E_ENABLE_PIN -1 - -#define SDPOWER -1 -#define SDSS -1 -#define LED_PIN -1 -#define FAN_PIN -1 -#define PS_ON_PIN 15 -#define KILL_PIN -1 - -#define HEATER_0_PIN 6 -#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! - - - - - - -/**************************************************************************************** -* Sanguino/RepRap Motherboard with direct-drive extruders -* -* ATMega644P -* -* +---\/---+ -* (D 0) PB0 1| |40 PA0 (AI 0 / D31) -* (D 1) PB1 2| |39 PA1 (AI 1 / D30) -* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) -* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) -* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) -* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) -* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) -* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) -* RST 9| |32 AREF -* VCC 10| |31 GND -* GND 11| |30 AVCC -* XTAL2 12| |29 PC7 (D 23) -* XTAL1 13| |28 PC6 (D 22) -* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI -* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO -* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS -* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK -* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA -* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL -* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM -* +--------+ -* -****************************************************************************************/ -#elif MOTHERBOARD == 1 -#ifndef __AVR_ATmega644P__ -#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. -#endif - -#define X_STEP_PIN 15 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN 19 -#define X_MIN_PIN 20 -#define X_MAX_PIN 21 - -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_ENABLE_PIN 19 -#define Y_MIN_PIN 25 -#define Y_MAX_PIN 26 - -#define Z_STEP_PIN 29 -#define Z_DIR_PIN 30 -#define Z_ENABLE_PIN 31 -#define Z_MIN_PIN 2 -#define Z_MAX_PIN 1 - -#define E_STEP_PIN 12 -#define E_DIR_PIN 16 -#define E_ENABLE_PIN 3 - -#define SDPOWER -1 -#define SDSS -1 -#define LED_PIN 0 -#define FAN_PIN -1 -#define PS_ON_PIN -1 -#define KILL_PIN -1 - -#define HEATER_0_PIN 14 -#define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! - -/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ - - - - - - -/**************************************************************************************** -* RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---******* -* -****************************************************************************************/ -#elif MOTHERBOARD == 2 -#ifndef __AVR_ATmega644P__ -#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. -#endif - -#define X_STEP_PIN 15 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN 19 -#define X_MIN_PIN 20 -#define X_MAX_PIN 21 - -#define Y_STEP_PIN 23 -#define Y_DIR_PIN 22 -#define Y_ENABLE_PIN 24 -#define Y_MIN_PIN 25 -#define Y_MAX_PIN 26 - -#define Z_STEP_PINN 27 -#define Z_DIR_PINN 28 -#define Z_ENABLE_PIN 29 -#define Z_MIN_PIN 30 -#define Z_MAX_PIN 31 - -#define E_STEP_PIN 17 -#define E_DIR_PIN 16 -#define E_ENABLE_PIN -1 - -#define SDPOWER -1 -#define SDSS 4 -#define LED_PIN 0 - -#define SD_CARD_WRITE 2 -#define SD_CARD_DETECT 3 -#define SD_CARD_SELECT 4 - -//our RS485 pins -#define TX_ENABLE_PIN 12 -#define RX_ENABLE_PIN 13 - -//pin for controlling the PSU. -#define PS_ON_PIN 14 - -#define FAN_PIN -1 -#define KILL_PIN -1 - -#define HEATER_0_PIN -1 -#define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! - - - - - - -/**************************************************************************************** -* Arduino Mega pin assignment -* -****************************************************************************************/ -#elif MOTHERBOARD == 3 -//////////////////FIX THIS////////////// -#ifndef __AVR_ATmega1280__ - #ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. - #endif -#endif - -// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1 -// #define RAMPS_V_1_3 -// #define RAMPS_V_1_0 - - -#ifdef RAMPS_V_1_3 - -#define X_STEP_PIN 54 -#define X_DIR_PIN 55 -#define X_ENABLE_PIN 38 -#define X_MIN_PIN 3 -#define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable. - -#define Y_STEP_PIN 60 -#define Y_DIR_PIN 61 -#define Y_ENABLE_PIN 56 -#define Y_MIN_PIN 14 -#define Y_MAX_PIN -1 //15 - -#define Z_STEP_PIN 46 -#define Z_DIR_PIN 48 -#define Z_ENABLE_PIN 62 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN -1 //19 - -#define E_STEP_PIN 26 -#define E_DIR_PIN 28 -#define E_ENABLE_PIN 24 - -#define SDPOWER -1 -#define SDSS 53 -#define LED_PIN 13 -#define FAN_PIN 9 -#define PS_ON_PIN 12 -#define KILL_PIN -1 - -#define HEATER_0_PIN 10 -#define HEATER_1_PIN 8 -#define TEMP_0_PIN 13 // ANALOG NUMBERING -#define TEMP_1_PIN 14 // ANALOG NUMBERING - - -#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default - -#define X_STEP_PIN 26 -#define X_DIR_PIN 28 -#define X_ENABLE_PIN 24 -#define X_MIN_PIN 3 -#define X_MAX_PIN -1 //2 - -#define Y_STEP_PIN 38 -#define Y_DIR_PIN 40 -#define Y_ENABLE_PIN 36 -#define Y_MIN_PIN 16 -#define Y_MAX_PIN -1 //17 - -#define Z_STEP_PIN 44 -#define Z_DIR_PIN 46 -#define Z_ENABLE_PIN 42 -#define Z_MIN_PIN 18 -#define Z_MAX_PIN -1 //19 - -#define E_STEP_PIN 32 -#define E_DIR_PIN 34 -#define E_ENABLE_PIN 30 - -#define SDPOWER 48 -#define SDSS 53 -#define LED_PIN 13 -#define PS_ON_PIN -1 -#define KILL_PIN -1 - - - -#ifdef RAMPS_V_1_0 // RAMPS_V_1_0 - #define HEATER_0_PIN 12 // RAMPS 1.0 - #define HEATER_1_PIN -1 // RAMPS 1.0 - #define FAN_PIN 11 // RAMPS 1.0 - -#else // RAMPS_V_1_1 or RAMPS_V_1_2 - #define HEATER_0_PIN 10 // RAMPS 1.1 - #define HEATER_1_PIN 8 // RAMPS 1.1 - #define FAN_PIN 9 // RAMPS 1.1 -#endif - -#define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#endif - -// SPI for Max6675 Thermocouple - -#ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support #define SCK_PIN 52 - #define MISO_PIN 50 - #define MOSI_PIN 51 - #define MAX6675_SS 53 -#else - #define MAX6675_SS 49 -#endif - - - -/**************************************************************************************** -* Duemilanove w/ ATMega328P pin assignment -* -****************************************************************************************/ -#elif MOTHERBOARD == 4 -#ifndef __AVR_ATmega328P__ -#error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu. -#endif - -#define X_STEP_PIN 19 -#define X_DIR_PIN 18 -#define X_ENABLE_PIN -1 -#define X_MIN_PIN 17 -#define X_MAX_PIN -1 - -#define Y_STEP_PIN 10 -#define Y_DIR_PIN 7 -#define Y_ENABLE_PIN -1 -#define Y_MIN_PIN 8 -#define Y_MAX_PIN -1 - -#define Z_STEP_PIN 13 -#define Z_DIR_PIN 3 -#define Z_ENABLE_PIN 2 -#define Z_MIN_PIN 4 -#define Z_MAX_PIN -1 - -#define E_STEP_PIN 11 -#define E_DIR_PIN 12 -#define E_ENABLE_PIN -1 - -#define SDPOWER -1 -#define SDSS -1 -#define LED_PIN -1 -#define FAN_PIN 5 -#define PS_ON_PIN -1 -#define KILL_PIN -1 - -#define HEATER_0_PIN 6 -#define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! - - - - -/**************************************************************************************** -* Gen6 pin assignment -* -****************************************************************************************/ -#elif MOTHERBOARD == 5 - -#ifndef __AVR_ATmega644P__ - #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. -#endif - -//x axis pins - #define X_STEP_PIN 15 - #define X_DIR_PIN 18 - #define X_ENABLE_PIN 19 - #define X_MIN_PIN 20 - #define X_MAX_PIN -1 - - //y axis pins - #define Y_STEP_PIN 23 - #define Y_DIR_PIN 22 - #define Y_ENABLE_PIN 24 - #define Y_MIN_PIN 25 - #define Y_MAX_PIN -1 - - //z axis pins - #define Z_STEP_PIN 27 - #define Z_DIR_PIN 28 - #define Z_ENABLE_PIN 29 - #define Z_MIN_PIN 30 - #define Z_MAX_PIN -1 - - //extruder pins - #define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715 - #define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715 - #define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715 - #define TEMP_0_PIN 5 //changed @ rkoeppl 20110410 - #define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 - #define HEATER_1_PIN -1 //changed @ rkoeppl 20110410 - - - #define SDPOWER -1 - #define SDSS -1 - #define LED_PIN -1 //changed @ rkoeppl 20110410 - #define TEMP_1_PIN -1 //changed @ rkoeppl 20110410 - #define FAN_PIN -1 //changed @ rkoeppl 20110410 - #define PS_ON_PIN -1 //changed @ rkoeppl 20110410 - //our pin for debugging. - - #define DEBUG_PIN 0 - - //our RS485 pins - #define TX_ENABLE_PIN 12 - #define RX_ENABLE_PIN 13 - - -/**************************************************************************************** -* Sanguinololu pin assignment -* -****************************************************************************************/ -#elif MOTHERBOARD == 6 -#ifndef __AVR_ATmega644P__ -#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. -#endif - -// uncomment the following line for Sanguinololu v1.2, comment for 1.1 or earlier. -// #define SANGUINOLOLU_V_1_2 - - -#define X_STEP_PIN 15 -#define X_DIR_PIN 21 -#define X_ENABLE_PIN -1 -#define X_MIN_PIN 18 -#define X_MAX_PIN -2 //2 - -#define Y_STEP_PIN 22 -#define Y_DIR_PIN 23 -#define Y_ENABLE_PIN -1 -#define Y_MIN_PIN 19 -#define Y_MAX_PIN -1 //17 - -#define Z_STEP_PIN 3 -#define Z_DIR_PIN 2 -// zenable defined by platform below -#define Z_MIN_PIN 20 -#define Z_MAX_PIN -1 //19 - -#define E_STEP_PIN 1 -#define E_DIR_PIN 0 -#define E_ENABLE_PIN -1 - -#define LED_PIN -1 - -#define FAN_PIN -1 // THIS LINE FOR V1.0 - -#define PS_ON_PIN -1 -#define KILL_PIN -1 - -#define HEATER_0_PIN 13 // THIS LINE FOR V1.0+ (extruder) - -#ifdef SANGUINOLOLU_V_1_2 - -#define HEATER_1_PIN 12 // (bed) -#define Z_ENABLE_PIN 26 - -#else - -#define HEATER_1_PIN 14 // (bed) -#define Z_ENABLE_PIN -1 - -#endif - -#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) -#define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) -#define SDPOWER -1 -#define SDSS 31 - -#else - -#error Unknown MOTHERBOARD value in configuration.h - -#endif - -#endif -- cgit v1.2.1