From 38660dbd399746bbd2c042755e5b1ffc5ffce457 Mon Sep 17 00:00:00 2001 From: Nils Date: Thu, 12 May 2011 14:26:31 +0200 Subject: Adding experimental support for max temperature gueard (M143) --- Tonokip_Firmware/Tonokip_Firmware.pde | 14 ++++++++++++++ Tonokip_Firmware/configuration.h | 7 +++++++ 2 files changed, 21 insertions(+) (limited to 'Tonokip_Firmware') diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde index 9c395f8..c1f11dd 100644 --- a/Tonokip_Firmware/Tonokip_Firmware.pde +++ b/Tonokip_Firmware/Tonokip_Firmware.pde @@ -83,6 +83,7 @@ void kill(byte debug); // M92 - Set axis_steps_per_unit - same syntax as G92 // M115 - Capabilities string // M140 - Set bed target temp +// M143 - Set maximum hot-end temperature // M190 - Wait for bed current temp to reach target temp. @@ -170,6 +171,9 @@ unsigned long watchmillis=0; #ifdef MINTEMP int minttemp=temp2analog(MINTEMP); #endif +#ifdef MAXTEMP +int maxttemp=temp2analog(MAXTEMP); +#endif //Inactivity shutdown variables unsigned long previous_millis_cmd=0; @@ -693,6 +697,9 @@ inline void process_commands() case 140: // M140 set bed temp if (code_seen('S')) target_bed_raw = temp2analogBed(code_value()); break; + case 143: // M143 set maximum hotend temperature + if (code_seen('S')) maxttemp = temp2analog(code_value()); + break; case 105: // M105 #if (TEMP_0_PIN>-1) || defined (HEATER_USES_MAX6675) tt=analog2temp(current_raw); @@ -1325,6 +1332,12 @@ inline void manage_heater() if(current_raw<=minttemp) target_raw=0; #endif + #ifdef MAXTEMP + if(current_raw>maxttemp) { + // We are too hot. Emergency brake to protect hotend + kill(5); + } + #endif #if (TEMP_0_PIN > -1) || defined (HEATER_USES_MAX66675) #ifdef PIDTEMP error = target_raw - current_raw; @@ -1528,6 +1541,7 @@ inline void kill(byte debug) case 2: Serial.print("Linear Move Abort, Last Line: "); break; case 3: Serial.print("Homing X Min Stop Fail, Last Line: "); break; case 4: Serial.print("Homing Y Min Stop Fail, Last Line: "); break; + case 5: Serial.print("Hot-end overheat protection, Last Line: "); break; } Serial.println(gcode_LastN); delay(5000); // 5 Second delay diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h index 97e94bc..de4d04e 100644 --- a/Tonokip_Firmware/configuration.h +++ b/Tonokip_Firmware/configuration.h @@ -61,6 +61,13 @@ float min_constant_speed_units = 2; // the minimum units of an accelerated move //The minimal temperature defines the temperature below which the heater will not be enabled //#define MINTEMP +//Experimental max temp +//When temperature exceeds max temp, your bot will halt. +//This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +//You should use MINTEMP for thermistor short/failure protection. +//Can be customized using M143 +//#define MAXTEMP 275 + // Select one of these only to define how the nozzle temp is read. #define HEATER_USES_THERMISTOR //#define HEATER_USES_AD595 -- cgit v1.2.1 From 889d6a7c5b5e715fd49dfb559704ab1dfc009746 Mon Sep 17 00:00:00 2001 From: Nils Date: Thu, 12 May 2011 23:24:59 +0200 Subject: Removing MCode for overheat protection --- Tonokip_Firmware/Tonokip_Firmware.pde | 4 ---- Tonokip_Firmware/configuration.h | 1 - 2 files changed, 5 deletions(-) (limited to 'Tonokip_Firmware') diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde index 43434b1..c2ad00e 100644 --- a/Tonokip_Firmware/Tonokip_Firmware.pde +++ b/Tonokip_Firmware/Tonokip_Firmware.pde @@ -52,7 +52,6 @@ // M92 - Set axis_steps_per_unit - same syntax as G92 // M115 - Capabilities string // M140 - Set bed target temp -// M143 - Set maximum hot-end temperature // M190 - Wait for bed current temp to reach target temp. // M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) // M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) @@ -660,9 +659,6 @@ inline void process_commands() case 140: // M140 set bed temp if (code_seen('S')) target_bed_raw = temp2analogBed(code_value()); break; - case 143: // M143 set maximum hotend temperature - if (code_seen('S')) maxttemp = temp2analog(code_value()); - break; case 105: // M105 #if (TEMP_0_PIN>-1) || defined (HEATER_USES_MAX6675) tt=analog2temp(current_raw); diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h index de4d04e..47466ae 100644 --- a/Tonokip_Firmware/configuration.h +++ b/Tonokip_Firmware/configuration.h @@ -65,7 +65,6 @@ float min_constant_speed_units = 2; // the minimum units of an accelerated move //When temperature exceeds max temp, your bot will halt. //This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! //You should use MINTEMP for thermistor short/failure protection. -//Can be customized using M143 //#define MAXTEMP 275 // Select one of these only to define how the nozzle temp is read. -- cgit v1.2.1