From 40249d192f60818db39abdcd8f0e66e49d466d3a Mon Sep 17 00:00:00 2001
From: Tommy Cheng <tommy.cheng@gmail.com>
Date: Sat, 30 Apr 2011 02:17:22 +0800
Subject: Adding Support for Sanguinololu

---
 Tonokip_Firmware/Tonokip_Firmware.pde |  1 +
 Tonokip_Firmware/configuration.h      |  2 +-
 Tonokip_Firmware/pins.h               | 43 +++++++++++++++++++++++++++++++++++
 3 files changed, 45 insertions(+), 1 deletion(-)

(limited to 'Tonokip_Firmware')

diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde
index bb744db..89f8ff7 100644
--- a/Tonokip_Firmware/Tonokip_Firmware.pde
+++ b/Tonokip_Firmware/Tonokip_Firmware.pde
@@ -210,6 +210,7 @@ void setup()
   if(E_ENABLE_PIN > -1) pinMode(E_ENABLE_PIN,OUTPUT);
 
   if(HEATER_0_PIN > -1) pinMode(HEATER_0_PIN,OUTPUT);
+  if(HEATER_1_PIN > -1) pinMode(HEATER_1_PIN,OUTPUT);
   
 #ifdef HEATER_USES_MAX6675
   digitalWrite(SCK_PIN,0);
diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h
index aba5176..b8e477c 100644
--- a/Tonokip_Firmware/configuration.h
+++ b/Tonokip_Firmware/configuration.h
@@ -3,7 +3,7 @@
 
 // NO RS485/EXTRUDER CONTROLLER SUPPORT
 // PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!!
-#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5
+#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5, Sanguinololu = 6
 
 //Comment out to disable SD support
 #define SDSUPPORT 1
diff --git a/Tonokip_Firmware/pins.h b/Tonokip_Firmware/pins.h
index eb305cb..282961f 100644
--- a/Tonokip_Firmware/pins.h
+++ b/Tonokip_Firmware/pins.h
@@ -358,6 +358,49 @@
     #define RX_ENABLE_PIN	13
 
 
+/****************************************************************************************
+* Sanguinololu pin assignment
+*
+****************************************************************************************/
+#elif MOTHERBOARD == 6
+#ifndef __AVR_ATmega644P__
+#error Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
+#endif
+
+#define X_STEP_PIN         15
+#define X_DIR_PIN          21
+#define X_ENABLE_PIN       -1
+#define X_MIN_PIN          18
+#define X_MAX_PIN           -2 //2
+
+#define Y_STEP_PIN         22
+#define Y_DIR_PIN          23
+#define Y_ENABLE_PIN       -1
+#define Y_MIN_PIN          19
+#define Y_MAX_PIN          -1 //17
+
+#define Z_STEP_PIN         3
+#define Z_DIR_PIN          2
+#define Z_ENABLE_PIN       -1
+#define Z_MIN_PIN          20
+#define Z_MAX_PIN          -1 //19
+
+#define E_STEP_PIN         1
+#define E_DIR_PIN          0
+#define E_ENABLE_PIN       -1
+
+#define LED_PIN            -1
+
+#define FAN_PIN            -1 // THIS LINE FOR V1.0
+
+#define PS_ON_PIN          -1
+#define KILL_PIN           -1
+
+#define HEATER_0_PIN       13 // THIS LINE FOR V1.0 (extruder)
+#define HEATER_1_PIN       14 // THIS LINE FOR V1.0 (bed)
+
+#define TEMP_0_PIN          7   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
+#define TEMP_1_PIN          6   // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
 
 #else
 
-- 
cgit v1.2.1