From 61b732cca3a678b8e7ed0107a7b2afdc73966014 Mon Sep 17 00:00:00 2001
From: Christopher Jansen <scribblej@yahoo.com>
Date: Tue, 3 May 2011 01:33:29 -0500
Subject: Minor changes to comments and fix to upload target for arduino 0022

---
 Tonokip_Firmware/Makefile | 28 +++++++++++++---------------
 1 file changed, 13 insertions(+), 15 deletions(-)

(limited to 'Tonokip_Firmware')

diff --git a/Tonokip_Firmware/Makefile b/Tonokip_Firmware/Makefile
index d847f13..7f4f23e 100644
--- a/Tonokip_Firmware/Makefile
+++ b/Tonokip_Firmware/Makefile
@@ -1,35 +1,33 @@
+# Sprinter Arduino Project Makefile
+# 
+# Makefile Based on:
 # Arduino 0011 Makefile
 # Arduino adaptation by mellis, eighthave, oli.keller
 #
+# This has been tested with Arduino 0022.
+# 
 # This makefile allows you to build sketches from the command line
 # without the Arduino environment (or Java).
 #
 # Detailed instructions for using the makefile:
 #
-#  1. Copy this file into the folder with your sketch. There should be a
-#     file with the same name as the folder and with the extension .pde
-#     (e.g. foo.pde in the foo/ folder).
-#
-#  2. Modify the line containg "INSTALL_DIR" to point to the directory that
+#  1. Modify the line containg "INSTALL_DIR" to point to the directory that
 #     contains the Arduino installation (for example, under Mac OS X, this
 #     might be /Applications/arduino-0012).
 #
-#  3. Modify the line containing "PORT" to refer to the filename
+#  2. Modify the line containing "PORT" to refer to the filename
 #     representing the USB or serial connection to your Arduino board
 #     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
 #     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*).
 #
-#  4. Set the line containing "MCU" to match your board's processor. 
+#  3. Set the line containing "MCU" to match your board's processor. 
 #     Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth
 #     or Diecimila have the atmega168.  If you're using a LilyPad Arduino,
 #     change F_CPU to 8000000.
 #
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
+#  4. Type "make" and press enter to compile/verify your program.
 #
-#  7. Type "make upload", reset your Arduino board, and press enter to
+#  5. Type "make upload", reset your Arduino board, and press enter to
 #     upload your program to the Arduino board.
 #
 # $Id$
@@ -39,7 +37,7 @@ INSTALL_DIR = /home/chris/arduino-0022
 UPLOAD_RATE = 38400
 AVRDUDE_PROGRAMMER = stk500v1
 PORT = /dev/ttyUSB0
-MCU = atmega644p
+MCU = atmega2560
 F_CPU = 16000000
 
 
@@ -53,7 +51,7 @@ $(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
 $(ARDUINO)/wiring_pulse.c $(ARDUINO)/wiring_serial.c \
 $(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
 CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \
-$(ARDUINO)/Print.cpp
+$(ARDUINO)/Print.cpp ./SdFile.cpp ./SdVolume.cpp ./Sd2Card.cpp
 FORMAT = ihex
 
 
@@ -95,7 +93,7 @@ LDFLAGS = -lm
 # Programming support using avrdude. Settings and variables.
 AVRDUDE_PORT = $(PORT)
 AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf \
+AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avrdude.conf \
 -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
 -b $(UPLOAD_RATE)
 
-- 
cgit v1.2.1