// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
// Licence: GPL
#include <WProgram.h>
#include "fastio.h"

extern "C" void __cxa_pure_virtual();


#if X_ENABLE_PIN > -1
#define  enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
#define enable_x() ;
#define disable_x() ;
#endif
#if Y_ENABLE_PIN > -1
#define  enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#else
#define enable_y() ;
#define disable_y() ;
#endif
#if Z_ENABLE_PIN > -1
#define  enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#else
#define enable_z() ;
#define disable_z() ;
#endif
#if E_ENABLE_PIN > -1
#define  enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e() ;
#define disable_e() ;
#endif

#define X_AXIS 0
#define Y_AXIS 1
#define Z_AXIS 2
#define E_AXIS 3


// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in 
// the source g-code and may never actually be reached if acceleration management is active.
typedef struct {
  // Fields used by the bresenham algorithm for tracing the line
  long steps_x, steps_y, steps_z, steps_e;  // Step count along each axis

  long step_event_count;                    // The number of step events required to complete this block
  volatile long accelerate_until;           // The index of the step event on which to stop acceleration
  volatile long decelerate_after;           // The index of the step event on which to start decelerating
  volatile long acceleration_rate;          // The acceleration rate used for acceleration calculation
  unsigned char direction_bits;             // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)

  #ifdef ADVANCE
    long advance_rate;
    volatile long initial_advance;
    volatile long final_advance;
    float advance;
  #endif

  // Fields used by the motion planner to manage acceleration
  float speed_x, speed_y, speed_z, speed_e;          // Nominal mm/minute for each axis
  float nominal_speed;                               // The nominal speed for this block in mm/min  
  float millimeters;                                 // The total travel of this block in mm
  float entry_speed;
  float acceleration;                                // acceleration mm/sec^2

  // Settings for the trapezoid generator
  long nominal_rate;                                 // The nominal step rate for this block in step_events/sec 
  volatile long initial_rate;                        // The jerk-adjusted step rate at start of block  
  volatile long final_rate;                          // The minimal rate at exit
  long acceleration_st;                              // acceleration steps/sec^2
  volatile char busy;
} block_t;


void FlushSerialRequestResend();
void ClearToSend();

void showString (PGM_P s);

void manage_inactivity(byte debug);


void get_coordinates();
void prepare_move();
void prepare_arc_move(char isclockwise);
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);

void kill(byte debug);

void check_axes_activity();
void plan_init();
void st_init();
void tp_init();
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
void plan_set_position(float x, float y, float z, float e);
void st_wake_up();
void st_synchronize();


#ifdef DEBUG
void log_message(char*   message);
void log_bool(char* message, bool value);
void log_int(char* message, int value);
void log_long(char* message, long value);
void log_float(char* message, float value);
void log_uint(char* message, unsigned int value);
void log_ulong(char* message, unsigned long value);
#endif