#ifndef PINS_H #define PINS_H #define ALARM_PIN -1 /**************************************************************************************** * Arduino pin assignment * * ATMega168 * +-\/-+ * PC6 1| |28 PC5 (AI 5 / D19) * (D 0) PD0 2| |27 PC4 (AI 4 / D18) * (D 1) PD1 3| |26 PC3 (AI 3 / D17) * (D 2) PD2 4| |25 PC2 (AI 2 / D16) * PWM+ (D 3) PD3 5| |24 PC1 (AI 1 / D15) * (D 4) PD4 6| |23 PC0 (AI 0 / D14) * VCC 7| |22 GND * GND 8| |21 AREF * PB6 9| |20 AVCC * PB7 10| |19 PB5 (D 13) * PWM+ (D 5) PD5 11| |18 PB4 (D 12) * PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM * (D 7) PD7 13| |16 PB2 (D 10) PWM * (D 8) PB0 14| |15 PB1 (D 9) PWM * +----+ ****************************************************************************************/ #if MOTHERBOARD == 0 #define KNOWN_BOARD 1 #ifndef __AVR_ATmega168__ #error Oops! Make sure you have 'Arduino Diecimila' selected from the boards menu. #endif #define X_STEP_PIN 2 #define X_DIR_PIN 3 #define X_ENABLE_PIN -1 #define X_MIN_PIN 4 #define X_MAX_PIN 9 #define Y_STEP_PIN 10 #define Y_DIR_PIN 7 #define Y_ENABLE_PIN -1 #define Y_MIN_PIN 8 #define Y_MAX_PIN 13 #define Z_STEP_PIN 19 #define Z_DIR_PIN 18 #define Z_ENABLE_PIN 5 #define Z_MIN_PIN 17 #define Z_MAX_PIN 16 #define E_STEP_PIN 11 #define E_DIR_PIN 12 #define E_ENABLE_PIN -1 #define SDPOWER -1 #define SDSS -1 #define LED_PIN -1 #define FAN_PIN -1 #define PS_ON_PIN 15 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN 6 #define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #endif /**************************************************************************************** * Sanguino/RepRap Motherboard with direct-drive extruders * * ATMega644P * * +---\/---+ * (D 0) PB0 1| |40 PA0 (AI 0 / D31) * (D 1) PB1 2| |39 PA1 (AI 1 / D30) * INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29) * PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28) * PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27) * MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26) * MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25) * SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24) * RST 9| |32 AREF * VCC 10| |31 GND * GND 11| |30 AVCC * XTAL2 12| |29 PC7 (D 23) * XTAL1 13| |28 PC6 (D 22) * RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI * TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO * INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS * INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK * PWM (D 12) PD4 18| |23 PC1 (D 17) SDA * PWM (D 13) PD5 19| |22 PC0 (D 16) SCL * PWM (D 14) PD6 20| |21 PD7 (D 15) PWM * +--------+ * **************************************************************************************** * * ATMega644P (SMD) * * +--------+ * MOSI (D 5) PB5 1| O |44 PB4 (D 4) PWM * MISO (D 6) PB6 2| |43 PB3 (D 3) PWM * SCK (D 7) PB7 3| |42 PB2 (D 2) INT2 * RST 4| |41 PB1 (D 1) * Vcc 5| |40 PB0 (D 0) * GND 6| |39 GND * XTAL2 7| |38 Vcc * XTAL1 8| |37 PA0 (AI 0 / D31) * RX0 (D 8) PD0 9| |36 PA1 (AI 1 / D30) * TX0 (D 9) PD1 10| |35 PA2 (AI 2 / D29) * INT0 RX1 (D 10) PD2 11| |34 PA3 (AI 3 / D28) * + + * INT1 TX1 (D 11) PD3 12| |33 PA4 (AI 4 / D27) * PWM (D 12) PD4 13| |32 PA5 (AI 5 / D26) * PWM (D 13) PD5 14| |31 PA6 (AI 6 / D25) * PWM (D 14) PD6 15| |30 PA7 (AI 7 / D24) * PWM (D 15) PD7 16| |29 AREF * Vcc 17| |28 GND * GND 18| |27 AVCC * (D 16) PC0 19| |26 PC7 (D 23) * (D 17) PC1 20| |25 PC6 (D 22) * (D 18) PC2 21| |24 PC5 (D 21) TDI * (D 19) PC3 22| |23 PC4 (D 20) TDO * +--------+ * ****************************************************************************************/ #if MOTHERBOARD == 1 #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_ENABLE_PIN 19 #define X_MIN_PIN 20 #define X_MAX_PIN 21 #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 19 #define Y_MIN_PIN 25 #define Y_MAX_PIN 26 #define Z_STEP_PIN 29 #define Z_DIR_PIN 30 #define Z_ENABLE_PIN 31 #define Z_MIN_PIN 2 #define Z_MAX_PIN 1 #define E_STEP_PIN 12 #define E_DIR_PIN 16 #define E_ENABLE_PIN 3 #define SDPOWER -1 #define SDSS -1 #define LED_PIN 0 #define FAN_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN 14 #define TEMP_0_PIN 4 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ #endif /**************************************************************************************** * RepRap Motherboard ****---NOOOOOO RS485/EXTRUDER CONTROLLER!!!!!!!!!!!!!!!!!---******* * ****************************************************************************************/ #if MOTHERBOARD == 2 #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_ENABLE_PIN 19 #define X_MIN_PIN 20 #define X_MAX_PIN 21 #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 24 #define Y_MIN_PIN 25 #define Y_MAX_PIN 26 #define Z_STEP_PINN 27 #define Z_DIR_PINN 28 #define Z_ENABLE_PIN 29 #define Z_MIN_PIN 30 #define Z_MAX_PIN 31 #define E_STEP_PIN 17 #define E_DIR_PIN 16 #define E_ENABLE_PIN -1 #define SDPOWER -1 #define SDSS 4 #define LED_PIN 0 #define SD_CARD_WRITE 2 #define SD_CARD_DETECT 3 #define SD_CARD_SELECT 4 //our RS485 pins #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 //pin for controlling the PSU. #define PS_ON_PIN 14 #define FAN_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN -1 #define TEMP_0_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #endif /**************************************************************************************** * Gen3 PLUS for RepRap Motherboard V1.2 * ****************************************************************************************/ #if MOTHERBOARD == 21 #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif //x axis pins #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_ENABLE_PIN 19 #define X_MIN_PIN 20 #define X_MAX_PIN -1 //y axis pins #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 24 #define Y_MIN_PIN 25 #define Y_MAX_PIN -1 //z axis pins #define Z_STEP_PIN 27 #define Z_DIR_PIN 28 #define Z_ENABLE_PIN 29 #define Z_MIN_PIN 30 #define Z_MAX_PIN -1 #define E_DIR_PIN 21 #define E_STEP_PIN 17 #define E_ENABLE_PIN 13 //heaters //pin for hot end heater #define HEATER_0_PIN 12 //Pin for heated bed heater #define HEATER_1_PIN 16 //pin for debugging. #define DEBUG_PIN -1 //SD card pin #define SDSS 4 #define SDPOWER -1 #define FAN_PIN -1 #define TEMP_0_PIN 0 #define TEMP_1_PIN 5 #define LED_PIN -1 //pin for controlling the PSU. #define PS_ON_PIN 14 #endif /**************************************************************************************** * Gen3 Monolithic Electronics * ****************************************************************************************/ #if MOTHERBOARD == 22 #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif #define DEBUG_PIN 0 // x axis #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_MIN_PIN 20 #define X_ENABLE_PIN 24 //actually uses Y_enable_pin #define X_MAX_PIN -1 // y axes #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_MIN_PIN 25 #define Y_ENABLE_PIN 24 //shared with X_enable_pin #define Y_MAX_PIN -1 // z axes #define Z_STEP_PIN 27 #define Z_DIR_PIN 28 #define Z_MIN_PIN 30 #define Z_ENABLE_PIN 29 #define Z_MAX_PIN -1 //extruder pins #define E_STEP_PIN 12 #define E_DIR_PIN 17 #define E_ENABLE_PIN 3 #define HEATER_0_PIN 16 #define TEMP_0_PIN 0 #define FAN_PIN -1 //bed pins #define HEATER_1_PIN -1 #define TEMP_1_PIN -1 #define SDSS -1 #define SDPOWER -1 #define LED_PIN -1 //pin for controlling the PSU. #define PS_ON_PIN 14 #endif /**************************************************************************************** * Gen3 PLUS for TechZone Gen3 Remix Motherboard * ****************************************************************************************/ #if MOTHERBOARD == 23 #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif //x axis pins #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_ENABLE_PIN 24 //same as E/Y_enable_pin #define X_MIN_PIN 20 #define X_MAX_PIN -1 //y axis pins #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 24 //same as E/X_enable_pin #define Y_MIN_PIN 25 #define Y_MAX_PIN -1 //z axis pins #define Z_STEP_PIN 27 #define Z_DIR_PIN 28 #define Z_ENABLE_PIN 29 #define Z_MIN_PIN 30 #define Z_MAX_PIN -1 #define E_DIR_PIN 21 #define E_STEP_PIN 19 #define E_ENABLE_PIN 24 //same as X/Y_enable_pin //heaters //pin for hot end heater #define HEATER_0_PIN 16 //Pin for heated bed heater #define HEATER_1_PIN 17 //pin for debugging. #define DEBUG_PIN -1 //SD card pin #define SDSS 4 #define SDPOWER -1 #define FAN_PIN -1 #define TEMP_0_PIN 0 #define TEMP_1_PIN 5 #define LED_PIN -1 //pin for controlling the PSU. #define PS_ON_PIN 14 #endif /**************************************************************************************** * Arduino Mega pin assignment * ****************************************************************************************/ #if MOTHERBOARD == 33 #define MOTHERBOARD 3 #define RAMPS_V_1_3 #endif #if MOTHERBOARD == 3 #define KNOWN_BOARD 1 //////////////////FIX THIS////////////// #ifndef __AVR_ATmega1280__ #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #endif #endif // uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1 // #define RAMPS_V_1_3 // #define RAMPS_V_1_0 #ifdef RAMPS_V_1_3 #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 #define X_MIN_PIN 3 #define X_MAX_PIN -1 //2 //Max endstops default to disabled "-1", set to commented value to enable. #define Y_STEP_PIN 60 #define Y_DIR_PIN 61 #define Y_ENABLE_PIN 56 #define Y_MIN_PIN 14 #define Y_MAX_PIN -1 //15 #define Z_STEP_PIN 46 #define Z_DIR_PIN 48 #define Z_ENABLE_PIN 62 #define Z_MIN_PIN 18 #define Z_MAX_PIN -1 //19 #define E_STEP_PIN 26 #define E_DIR_PIN 28 #define E_ENABLE_PIN 24 #define E_1_STEP_PIN 36 #define E_1_DIR_PIN 34 #define E_1_ENABLE_PIN 30 #define SDPOWER -1 #define SDSS 53 #define LED_PIN 13 #define FAN_PIN 9 #define PS_ON_PIN 12 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN 10 #define HEATER_1_PIN 8 #define TEMP_0_PIN 13 // ANALOG NUMBERING #define TEMP_1_PIN 14 // ANALOG NUMBERING #define TEMP_2_PIN 15 // ANALOG NUMBERING #else // RAMPS_V_1_1 or RAMPS_V_1_2 as default #define X_STEP_PIN 26 #define X_DIR_PIN 28 #define X_ENABLE_PIN 24 #define X_MIN_PIN 3 #define X_MAX_PIN -1 //2 #define Y_STEP_PIN 38 #define Y_DIR_PIN 40 #define Y_ENABLE_PIN 36 #define Y_MIN_PIN 16 #define Y_MAX_PIN -1 //17 #define Z_STEP_PIN 44 #define Z_DIR_PIN 46 #define Z_ENABLE_PIN 42 #define Z_MIN_PIN 18 #define Z_MAX_PIN -1 //19 #define E_STEP_PIN 32 #define E_DIR_PIN 34 #define E_ENABLE_PIN 30 #define SDPOWER 48 #define SDSS 53 #define LED_PIN 13 #define PS_ON_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #ifdef RAMPS_V_1_0 // RAMPS_V_1_0 #define HEATER_0_PIN 12 // RAMPS 1.0 #define HEATER_1_PIN -1 // RAMPS 1.0 #define FAN_PIN 11 // RAMPS 1.0 #else // RAMPS_V_1_1 or RAMPS_V_1_2 #define HEATER_0_PIN 10 // RAMPS 1.1 #define HEATER_1_PIN 8 // RAMPS 1.1 #define FAN_PIN 9 // RAMPS 1.1 #endif #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #endif // SPI for Max6675 Thermocouple #ifndef SDSUPPORT // these pins are defined in the SD library if building with SD support #define SCK_PIN 52 #define MISO_PIN 50 #define MOSI_PIN 51 #define MAX6675_SS 53 #else #define MAX6675_SS 49 #endif #endif /**************************************************************************************** * Duemilanove w/ ATMega328P pin assignment * ****************************************************************************************/ #if MOTHERBOARD == 4 #define KNOWN_BOARD 1 #ifndef __AVR_ATmega328P__ #error Oops! Make sure you have 'Arduino Duemilanove w/ ATMega328' selected from the 'Tools -> Boards' menu. #endif #define X_STEP_PIN 19 #define X_DIR_PIN 18 #define X_ENABLE_PIN -1 #define X_MIN_PIN 17 #define X_MAX_PIN -1 #define Y_STEP_PIN 10 #define Y_DIR_PIN 7 #define Y_ENABLE_PIN -1 #define Y_MIN_PIN 8 #define Y_MAX_PIN -1 #define Z_STEP_PIN 13 #define Z_DIR_PIN 3 #define Z_ENABLE_PIN 2 #define Z_MIN_PIN 4 #define Z_MAX_PIN -1 #define E_STEP_PIN 11 #define E_DIR_PIN 12 #define E_ENABLE_PIN -1 #define SDPOWER -1 #define SDSS -1 #define LED_PIN -1 #define FAN_PIN 5 #define PS_ON_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN 6 #define TEMP_0_PIN 0 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #endif /**************************************************************************************** * Gen6 pin assignment * ****************************************************************************************/ #if MOTHERBOARD == 5 #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif //x axis pins #define X_STEP_PIN 15 #define X_DIR_PIN 18 #define X_ENABLE_PIN 19 #define X_MIN_PIN 20 #define X_MAX_PIN -1 //y axis pins #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 24 #define Y_MIN_PIN 25 #define Y_MAX_PIN -1 //z axis pins #define Z_STEP_PIN 27 #define Z_DIR_PIN 28 #define Z_ENABLE_PIN 29 #define Z_MIN_PIN 30 #define Z_MAX_PIN -1 //extruder pins #define E_STEP_PIN 4 //Edited @ EJE Electronics 20100715 #define E_DIR_PIN 2 //Edited @ EJE Electronics 20100715 #define E_ENABLE_PIN 3 //Added @ EJE Electronics 20100715 #define TEMP_0_PIN 5 //changed @ rkoeppl 20110410 #define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 #define HEATER_1_PIN -1 //changed @ rkoeppl 20110410 #define SDPOWER -1 #define SDSS 17 #define LED_PIN -1 //changed @ rkoeppl 20110410 #define TEMP_1_PIN -1 //changed @ rkoeppl 20110410 #define FAN_PIN -1 //changed @ rkoeppl 20110410 #define PS_ON_PIN -1 //changed @ rkoeppl 20110410 //our pin for debugging. #define DEBUG_PIN 0 //our RS485 pins #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 #endif /**************************************************************************************** * Sanguinololu pin assignment * ****************************************************************************************/ #if MOTHERBOARD == 62 #define MOTHERBOARD 6 #define SANGUINOLOLU_V_1_2 #endif #if MOTHERBOARD == 6 #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif #define X_STEP_PIN 15 #define X_DIR_PIN 21 #define X_MIN_PIN 18 #define X_MAX_PIN -2 #define Y_STEP_PIN 22 #define Y_DIR_PIN 23 #define Y_MIN_PIN 19 #define Y_MAX_PIN -1 #define Z_STEP_PIN 3 #define Z_DIR_PIN 2 #define Z_MIN_PIN 20 #define Z_MAX_PIN -1 #define E_STEP_PIN 1 #define E_DIR_PIN 0 #define LED_PIN -1 #define FAN_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #define HEATER_0_PIN 13 // (extruder) #ifdef SANGUINOLOLU_V_1_2 #define HEATER_1_PIN 12 // (bed) #define X_ENABLE_PIN 14 #define Y_ENABLE_PIN 14 #define Z_ENABLE_PIN 26 #define E_ENABLE_PIN 14 #else #define HEATER_1_PIN 14 // (bed) #define X_ENABLE_PIN -1 #define Y_ENABLE_PIN -1 #define Z_ENABLE_PIN -1 #define E_ENABLE_PIN -1 #endif #define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) #define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) #define SDPOWER -1 #define SDSS 31 #endif /**************************************************************************************** * Gen7 pin assignment * **************************************************************************************** * for Gen7 to work properly, you should reset your fuses to lfuse= 0xF7 ; hfuse = 0xD4 ; efuse = FD; * else you will always get a "brown out reset" loop resetting the firmware * you need a programmer to set the fuses **/ #if MOTHERBOARD == 71 //GEN7 with 20 Mhz #define MOTHERBOARD 7 #define QUARZ_20MHZ #endif #if MOTHERBOARD == 7 #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__) && !defined(__AVR_ATmega644__) #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. #endif //x axis pins #define X_STEP_PIN 19 #define X_DIR_PIN 18 #define X_ENABLE_PIN 24 #define X_MIN_PIN 7 #define X_MAX_PIN -1 //X - Maxpin is 6 //y axis pins #define Y_STEP_PIN 23 #define Y_DIR_PIN 22 #define Y_ENABLE_PIN 24 #define Y_MIN_PIN 5 #define Y_MAX_PIN -1 //Y - Maxpin is 2 //z axis pins #define Z_STEP_PIN 26 #define Z_DIR_PIN 25 #define Z_ENABLE_PIN 24 #define Z_MIN_PIN 1 #define Z_MAX_PIN -1 //Z - Maxpin is 0 //extruder pins #define E_STEP_PIN 28 #define E_DIR_PIN 27 #define E_ENABLE_PIN 24 #define TEMP_0_PIN 1 // Extruder #define HEATER_0_PIN 4 // Extruder #define HEATER_1_PIN 3 // Bed #define SDPOWER -1 #define SDSS -1 #define LED_PIN -1 #define TEMP_1_PIN 2 //Bed #define FAN_PIN -1 #define PS_ON_PIN 15 #endif /**************************************************************************************** * Teensylu 0.7 pin assingments (ATMEGA90USB) * Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE! ****************************************************************************************/ #if MOTHERBOARD == 8 #define MOTHERBOARD 8 #define KNOWN_BOARD 1 #define X_STEP_PIN 28 #define X_DIR_PIN 29 #define X_ENABLE_PIN 19 #define X_MIN_PIN 25 #define X_MAX_PIN -1 #define Y_STEP_PIN 30 #define Y_DIR_PIN 31 #define Y_ENABLE_PIN 26 #define Y_MIN_PIN 20 #define Y_MAX_PIN -1 #define Z_STEP_PIN 32 #define Z_DIR_PIN 33 #define Z_ENABLE_PIN 17 #define Z_MIN_PIN 27 #define Z_MAX_PIN -1 #define E_STEP_PIN 34 #define E_DIR_PIN 35 #define E_ENABLE_PIN 13 #define HEATER_0_PIN 15 // Extruder #define HEATER_1_PIN 14 // Bed #define FAN_PIN 16 // Fan #define TEMP_0_PIN 7 // Extruder #define TEMP_1_PIN 6 // Bed #define SDPOWER -1 #define SDSS 20 #define LED_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 #define ALARM_PIN -1 #ifndef SDSUPPORT // these pins are defined in the SD library if building with SD support #define SCK_PIN 21 #define MISO_PIN 22 #define MOSI_PIN 23 #endif #endif /**************************************************************************************** * Printrboard Rev. B pin assingments (ATMEGA90USB1286) * Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE! * See http://reprap.org/wiki/Printrboard for more info ****************************************************************************************/ #if MOTHERBOARD == 9 #define MOTHERBOARD 9 #define KNOWN_BOARD 1 #define X_STEP_PIN 28 #define X_DIR_PIN 29 #define X_ENABLE_PIN 19 #define X_MIN_PIN 47 #define X_MAX_PIN -1 #define Y_STEP_PIN 30 #define Y_DIR_PIN 31 #define Y_ENABLE_PIN 18 #define Y_MIN_PIN 20 #define Y_MAX_PIN -1 #define Z_STEP_PIN 32 #define Z_DIR_PIN 33 #define Z_ENABLE_PIN 17 #define Z_MIN_PIN 36 #define Z_MAX_PIN -1 #define E_STEP_PIN 34 #define E_DIR_PIN 35 #define E_ENABLE_PIN 13 #define HEATER_0_PIN 15 // Extruder #define HEATER_1_PIN 14 // Bed #define FAN_PIN 16 // Fan #define TEMP_0_PIN 1 // Extruder #define TEMP_1_PIN 0 // Bed #define SDPOWER -1 #define SDSS 2 #define LED_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 #ifndef SDSUPPORT // these pins are defined in the SD library if building with SD support #define SCK_PIN 21 #define MISO_PIN 22 #define MOSI_PIN 23 #endif #endif #ifndef KNOWN_BOARD #error Unknown MOTHERBOARD value in configuration.h #endif //List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! const int sensitive_pins[] = {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, FAN_PIN, TEMP_0_PIN, TEMP_1_PIN}; #endif