summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-08-18Merge pull request #71 from ParCan/masterkliment
ParCan Thermistor table added
2011-08-12Merge pull request #69 from changwoo/masterkliment
ATmega1284P support
2011-08-12Merge pull request #68 from WebSpider/experimentalkliment
Experimental adding of M109 cooldown handling
2011-08-12Merge pull request #67 from rotorit/masterkliment
use the fan pin to power the hot end heater on the crappy techzone monotronics
2011-08-11Adding falling mode to M109 to better implement GCode definitionNils
2011-08-09first revision... had to use the fan pin to control the extruder hot end ↵rotorit
heater. meaning.. this setup will not support a bed heat control ..for now... Time will show if I can get the Tip management A/D converter to work... or.. should i get it to work at all???
2011-08-09Merge pull request #66 from rotorit/masterkliment
Limited Gen 3 with 644P support - support gen3 with gen3+ board and the techzone monolithic electronics with thermistor only
2011-08-09typorotorit
2011-08-09Edited Sprinter/Configuration.h via GitHubrotorit
2011-08-09Added support for Gen3-pluss and Gen3-Monolithic Electronicsrotorit
2011-08-09added motherboard entry for Gen3-pluss and Gen3-Monolithic Electronicsrotorit
2011-08-09Support Sanguino/Sanguinololu with ATmega1284PChangwoo Ryu
2011-08-03Merge pull request #65 from blddk/masterkliment
M42 for toggling individual pins or setting PWM, modified MINTEMP to apply to heated bed
2011-08-03Fixed so commenting out MINTEMP won't break compile, however, commenting out ↵blddk
MINTEMP will then again allow the bed to be turned on, but not off, when there are no thermistor, or thermistor is broken.
2011-08-03Added MINTEMP to work on the heated bed too, so it will also turn off when ↵blddk
thermistor fails.
2011-08-02Added M42 to control non used pins example: M42 P23 S255blddk
2011-08-02Added a list of pins which will be ignored by manual change through M42blddk
2011-08-02When you set PWM on a pin to a given value and then WRITE a 0 to it, the PWM ↵Kliment
timer does not stop. Set the PWM to 0 as well to prevent hotend meltdowns.
2011-07-26Merge pull request #62 from alexrj/heater-current-limitkliment
Heater current limit
2011-07-26Merge pull request #61 from alexrj/temp-residencykliment
New implementation of TEMP_RESIDENCY_TIME
2011-07-26New config option HEATER_CURRENT to limit current to the nozzleAlessandro Ranellucci
2011-07-26New implementation of TEMP_RESIDENCY_TIME. We now wait for the target temp ↵Alessandro Ranellucci
to be esablished and maintained for residency time +/- a configurable hysteresis
2011-07-25Merge pull request #60 from LawrenceLeung/masterkliment
Support TEMP_RESIDENCY_TIME.
2011-07-25Comment out TEMP_RESIDENCY_TIMELawrence
2011-07-25Revert "Disable TEMP_RESIDENCY_TIME for default"Lawrence
This reverts commit eb1c87fa7bf2e4bcc8b074775d88a6e767de2c29.
2011-07-25Disable TEMP_RESIDENCY_TIME for defaultLawrence Leung larryleungcal@yahoo.com
2011-07-25add support for TEMP_RESIDENCY_TIME for M109Lawrence Leung larryleungcal@yahoo.com
2011-07-25Merge pull request #58 from Renosis/masterkliment
MakerGear Hybrid Prusa Mendel steps per unit values
2011-07-24Added MakerGear Hybrid Prusa steps per unit values.Spencer Renosis
2011-07-24Merge branch 'experimental'kliment
2011-07-24Merge remote branch 'origin/experimental' into experimentalEmanuele Caruso
2011-07-24Fixed bug which in some cases caused the moves to be done at full speed ↵Emanuele Caruso
without acceleration
2011-07-23Merge pull request #55 from Joaz/uuidkliment
added uuid identification support
2011-07-24added uuid identification supportjglauche
2011-07-18Merge branch 'master' into experimentalkliment
2011-07-17Merge pull request #54 from ERoth3/masterkliment
Added Ramps 1.3 Pin assignments for E1
2011-07-18Added Ramps 1.3 pin assignments for E1 (second extruder) stepper driverEmery Roth
This is my first commit…Please don't hurt me if i screw up!
2011-07-17Merge branch 'master' into experimentalkliment
2011-07-17Add some explanations to config, change some variables to #defines. Fixes #36kliment
2011-07-17Merge branch 'master' into experimentalkliment
2011-07-17Add extra config for homing feedrate - fixes #28kliment
2011-07-16Merge branch 'master' into experimentalkliment
2011-07-16Ignore bedtemp if no bed temp pin definedkliment
2011-07-16Merge branch 'master' of github.com:kliment/Sprinter into experimentalkliment
2011-07-16Merge pull request #52 from alexrj/inverted-homingkliment
Fix homing to max endstops
2011-07-16Bugfix: homing to max endstops didn't work because current_position was ↵Alessandro Ranellucci
always reset to 0.
2011-07-16Merge branch 'master' of github.com:kliment/Sprinter into experimentalkliment
2011-07-16Merge pull request #51 from alexrj/temp-smoothingkliment
Respect HEATER_USES_* when initializing temperature smoothing
2011-07-16Bugfix: smoothed temperature was initialized without respecting HEATER_USES_*Alessandro Ranellucci
2011-07-15Revert "Remove float conversions from step loop"kliment
This reverts commit b31c7a837ff5baff89043f3c06b1b2191ed9f79d.
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-23 12:29:27 +0000