| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-02-01 | Check Uart Puffer while circle processing (CMD: G2 / G3) | midopple | |
| 2012-01-29 | Merge commit '132f8c212e4c316559177e532df6b9a6c2205bf2' into experimental | midopple | |
| 2012-01-29 | Merge pull request #131 from midopple/SprinterV2 | kliment | |
| Lookahead, timer-based stepping, M30 file delete | |||
| 2012-01-29 | Add function to check the UART buffer while arc function is working | midopple | |
| 2012-01-29 | Update Changelog in Mainfile | midopple | |
| 2012-01-29 | Change Motherboard to 3 (standardsettings) | midopple | |
| 2012-01-29 | Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2 | midopple | |
| Conflicts: Sprinter/Configuration.h Sprinter/Sprinter.pde | |||
| 2012-01-29 | Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2 | midopple | |
| Conflicts: Sprinter/Configuration.h | |||
| 2012-01-29 | Change configuration.h to original settings | midopple | |
| 2012-01-29 | Change infotext | midopple | |
| 2012-01-29 | New Version Sprinter V2 | midopple | |
| - Look Vorward Funktion - - Stepper Control with Timer 1 - SOFT PWM for Extruder heating --> Free Timer 1 - G2 / G3 Command for arc real arc - Baudrate 250 kbaud - M30 Command delete file on SD Card - Text moved to flash to free RAM - M203 Command for Temp debugging | |||
| 2012-01-28 | Update Sprinter/Configuration.h | midopple | |
| 2012-01-27 | Merge pull request #129 from jschleic/patch-1 | kliment | |
| Improve Makefile to rebuild on upload | |||
| 2012-01-27 | fix indentation | Joachim Schleicher | |
| This should be a comment. Instead it is printed together with the 'upload' target, when idented. | |||
| 2012-01-22 | Merge pull request #128 from blddk/experimental | kliment | |
| Reported wrong temperature in M190 | |||
| 2012-01-22 | Reported wrong temperature while heating up | blddk | |
| 2012-01-22 | Merge pull request #127 from blddk/experimental | kliment | |
| Stepper enable delay and temperature table Fix bed temp reading in M190 | |||
| 2012-01-22 | Changed temperature table for bed, to the one for the bed, instead of for ↵ | blddk | |
| the heater. | |||
| 2012-01-22 | Added option to set a delay after enabling a stepper driver, default turned ↵ | blddk | |
| off to keep current behavior. | |||
| 2012-01-22 | Added option to set a delay after enabeling stepper driver, to allow the ↵ | blddk | |
| driver to enable (time needed according to datasheet) | |||
| 2012-01-20 | correct dependencies in Makefile | Joachim Schleicher | |
| applet/$(TARGET).elf should depend on the cpp file, not on .pde so that the cpp is rebuilt when pde changes. We drop the target applet_files to achieve the correct behaviour. Now 'make upload' does rebuild the hex file as well. | |||
| 2011-12-10 | Merge pull request #125 from gdahlm/experimental | kliment | |
| Fixes for Gen7 Support #2 | |||
| 2011-12-10 | Merge pull request #126 from ERoth3/patch-1 | kliment | |
| Updated readme with a warning about Arduino V1.0 incompatibility. | |||
| 2011-12-10 | Updated readme with a warning about Arduino V1.0 incompatibility. | ERoth3 | |
| 2011-12-06 | Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 ↵ | Greg Dahlman | |
| board in pins.h | |||
| 2011-12-05 | Fixing issues in pins.h and fastio.h, I created them not understanding it ↵ | Greg Dahlman | |
| was using arduino pin numbers I also put in a note that Gen 7 only works at 16 MHZ due to timing issues with WProgram.h and wiring.h | |||
| 2011-12-05 | Merge remote-tracking branch 'upstream/experimental' | Greg Dahlman | |
| Conflicts: Sprinter/pins.h | |||
| 2011-12-05 | Merge pull request #123 from FrozenFire/master | kliment | |
| Allow running a specifically-named file from SD on startup if found. | |||
| 2011-12-04 | Added an option to make init.g on SD run on boot. | Nathan Zadoks | |
| 2011-11-28 | Add gen7 to list of boards in configuration | Kliment Yanev | |
| Allow ATmega644 (non-P version) for Gen7 | |||
| 2011-11-28 | Merge branch 'master' into experimental | Kliment Yanev | |
| 2011-11-28 | Revert "Merge pull request #121 from Traumflug/master" | Kliment Yanev | |
| This reverts commit 11d3281a09e2a2f0ae7c9695f79d2d903c22716b, reversing changes made to f8c17d3b4655ba9b694c407ff174135badb914a5. | |||
| 2011-11-28 | Merge pull request #121 from Traumflug/master | kliment | |
| Allow ATmega644 for Gen7 | |||
| 2011-11-28 | pins.h: allow an ATmega644 (without P). | Markus Hitter | |
| 2011-11-16 | Merge pull request #119 from pipakin/experimental | kliment | |
| Block transfer | |||
| 2011-11-16 | M30/M31 fast sd block transfer | Philip Kin | |
| 2011-11-16 | M30/M31 fast sd block transfer | Philip Kin | |
| 2011-11-10 | Merge pull request #117 from sparr/patch-1 | kliment | |
| Mark Sanguinololu-specific steps in instructions. | |||
| 2011-11-10 | spelling correction | sparr | |
| 2011-11-10 | note Sanguino-specific steps | sparr | |
| 2011-11-10 | Merge branch 'master' into experimental | Kliment Yanev | |
| 2011-11-10 | Improve 200k thermistor table to better match reality | Kliment Yanev | |
| 2011-11-06 | Merge pull request #116 from cdaringe/master | kliment | |
| Experimental oscillation reduction | |||
| 2011-11-06 | osc reduction | Chris Dieringer | |
| 2011-11-04 | Merge pull request #114 from gdahlm/experimental | kliment | |
| Add missing #endif in gen7 definition in pins.h | |||
| 2011-11-03 | Edited pins.h to add missing #endif | Greg Dahlman | |
| 2011-11-03 | Added missing #endif to pins.h | Greg Dahlman | |
| 2011-11-03 | Merge pull request #112 from gdahlm/experimental | kliment | |
| Add Gen7 support | |||
| 2011-11-02 | Added Pin 33-40 digital defs to fastio.h for the 644 | Greg Dahlman | |
| 2011-11-02 | Added support for Gen7 Board | Greg Dahlman | |
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |