summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-01-22Added option to set a delay after enabling a stepper driver, default turned ↵blddk
off to keep current behavior.
2012-01-22Added option to set a delay after enabeling stepper driver, to allow the ↵blddk
driver to enable (time needed according to datasheet)
2012-01-20correct dependencies in MakefileJoachim Schleicher
applet/$(TARGET).elf should depend on the cpp file, not on .pde so that the cpp is rebuilt when pde changes. We drop the target applet_files to achieve the correct behaviour. Now 'make upload' does rebuild the hex file as well.
2011-12-10Merge pull request #125 from gdahlm/experimentalkliment
Fixes for Gen7 Support #2
2011-12-10Merge pull request #126 from ERoth3/patch-1kliment
Updated readme with a warning about Arduino V1.0 incompatibility.
2011-12-10Updated readme with a warning about Arduino V1.0 incompatibility. ERoth3
2011-12-06Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 ↵Greg Dahlman
board in pins.h
2011-12-05Fixing issues in pins.h and fastio.h, I created them not understanding it ↵Greg Dahlman
was using arduino pin numbers I also put in a note that Gen 7 only works at 16 MHZ due to timing issues with WProgram.h and wiring.h
2011-12-05Merge remote-tracking branch 'upstream/experimental'Greg Dahlman
Conflicts: Sprinter/pins.h
2011-12-05Merge pull request #123 from FrozenFire/masterkliment
Allow running a specifically-named file from SD on startup if found.
2011-12-04Added an option to make init.g on SD run on boot.Nathan Zadoks
2011-11-28Add gen7 to list of boards in configurationKliment Yanev
Allow ATmega644 (non-P version) for Gen7
2011-11-28Merge branch 'master' into experimentalKliment Yanev
2011-11-28Revert "Merge pull request #121 from Traumflug/master"Kliment Yanev
This reverts commit 11d3281a09e2a2f0ae7c9695f79d2d903c22716b, reversing changes made to f8c17d3b4655ba9b694c407ff174135badb914a5.
2011-11-28Merge pull request #121 from Traumflug/masterkliment
Allow ATmega644 for Gen7
2011-11-28pins.h: allow an ATmega644 (without P).Markus Hitter
2011-11-16Merge pull request #119 from pipakin/experimentalkliment
Block transfer
2011-11-16M30/M31 fast sd block transferPhilip Kin
2011-11-16M30/M31 fast sd block transferPhilip Kin
2011-11-10Merge pull request #117 from sparr/patch-1kliment
Mark Sanguinololu-specific steps in instructions.
2011-11-10spelling correctionsparr
2011-11-10note Sanguino-specific stepssparr
2011-11-10Merge branch 'master' into experimentalKliment Yanev
2011-11-10Improve 200k thermistor table to better match realityKliment Yanev
2011-11-06Merge pull request #116 from cdaringe/masterkliment
Experimental oscillation reduction
2011-11-06osc reductionChris Dieringer
2011-11-04Merge pull request #114 from gdahlm/experimentalkliment
Add missing #endif in gen7 definition in pins.h
2011-11-03Edited pins.h to add missing #endifGreg Dahlman
2011-11-03Added missing #endif to pins.hGreg Dahlman
2011-11-03Merge pull request #112 from gdahlm/experimentalkliment
Add Gen7 support
2011-11-02Added Pin 33-40 digital defs to fastio.h for the 644Greg Dahlman
2011-11-02Added support for Gen7 BoardGreg Dahlman
2011-10-29Define default value for alarm pinKliment Yanev
2011-10-29Merge pull request #110 from barclayo/patch-1kliment
Fix d calculation on XYZ moves where comparison was inside of abs() instead of comparing with the absolute value
2011-10-29Fix d calculation on XYZ moves where comparison was inside of abs() instead ↵barclayo
of comparing with the result.
2011-10-28Merge pull request #109 from Kerman/masterkliment
Moved footer in pins.h to end of file, fixing teensylu support
2011-10-28Moved pins.h footer to the end of the file, fixing teensylu supportJoe Kerman
2011-10-27Merge pull request #107 from k-eex/PIDkliment
Better default PID parameters
2011-10-27PID parameters for MakerGearKeegi
2011-10-27Merge pull request #106 from kliment/experimentalkliment
Merge Experimental into master
2011-10-27Merge branch 'master' of github.com:kliment/Sprinter into experimentalKliment Yanev
Conflicts: Sprinter/Configuration.h
2011-10-16Merge pull request #104 from blddk/experimentalkliment
Cooling fan control for a stepper driver fan - enable fan when stepper drivers are active
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Configuration.hblddk
2011-10-16Added options for the controller cooling fanblddk
2011-10-16Added function for controlling controller cooling fanblddk
2011-10-04Merge pull request #100 from Kerman/masterkliment
Support for Teensylu (at90usb1286)
2011-10-04i will figure out git eventuallyJoe Kerman
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-22 23:10:33 +0000