summaryrefslogtreecommitdiff
path: root/Sprinter/Sprinter.pde
AgeCommit message (Collapse)Author
2012-02-23fix comment mode.Joachim Schleicher
Closes #140. If a line starts with ';', it is ignored but comment_mode is reset. A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. Probably a similar fix is necessary for the SDSUPPORT part; I cannot test that part without an SD-shield.
2012-02-13changed homing function to not conflict with ↵Vyacheslav Kononenko
min_software_endstops/max_software_endstops
2011-12-04Added an option to make init.g on SD run on boot.Nathan Zadoks
2011-10-29Fix d calculation on XYZ moves where comparison was inside of abs() instead ↵barclayo
of comparing with the result.
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Added function for controlling controller cooling fanblddk
2011-10-01Merge branch 'master' of github.com:kliment/Sprinter into experimentalKliment Yanev
2011-09-28Fix scoping problem (fixes issue #70)Guillaume Seguin
2011-09-18Revert "Merge pull request #95 from AxTheB/master"Kliment Yanev
This reverts commit a27649c455c4d13385b32d45bf353ab890da052a, reversing changes made to 8fa84ce04eda414886cc5b075d7257e49b6f7f0a.
2011-09-18Merge pull request #95 from AxTheB/masterkliment
simplified string-to-number conversions
2011-09-17line numbers ale long, not intVáclav 'ax' Hůla
2011-09-17simplified string-to-number conversionsVáclav 'ax' Hůla
2011-09-17fixed typo, added even more PID improvements (these settings work out of box ↵Keegi
for my old hotend, but overshoot badly on MG hotend)
2011-09-17PID fixesKeegi
2011-09-17Reset heater pins after hard resets to avoid keeping them enabled while we ↵Alessandro Ranellucci
don't have temperature control anymore
2011-09-17Merge remote branch 'upstream/experimental' into alarm-pinAlessandro Ranellucci
Conflicts: Sprinter/Sprinter.pde
2011-09-17Signal an optional ALARM_PIN when reaching MAXTEMPAlessandro Ranellucci
Alarm signal can be dismissed by hard-resetting the board or by sending a M42 P23 S0 command (where 23 is the ALARM_PIN)
2011-09-17Initialize LED pin (was stuck after hard resets)Alessandro Ranellucci
2011-09-11Fix temp readings for multiple sensor types.unknown
Signed-off-by: Greg Frost <gregfrost1@bigpond.com>
2011-09-08Merge branch 'master' of github.com:kliment/Sprinter into experimentalKliment Yanev
2011-09-08Merge pull request #80 from alexrj/different-endstopskliment
Change ENDSTOPS_INVERTING to [XYZ]_ENDSTOP_INVERT
2011-09-04Merge pull request #83 from condac/patch-1kliment
Fix so the FAN pin is set as output and fixed fan off case for PWM pins
2011-09-04New and improved On and Off for FAN_PINcondac
2011-09-03Fix decelerationKliment Yanev
2011-09-03Merge branch 'master' into experimentalKliment Yanev
2011-09-03Fix underflow in steps per square secondKliment Yanev
2011-09-03Fix so the FAN works, added fan pin as output and fixed fan off case statementcondac
2011-08-29Refactoring acceleration math to a new setup_acceleration() function to make ↵Alessandro Ranellucci
M92 fully working.
2011-08-26Fixed typo in Z_ENDSTOP_INVERT patch by lemioAlessandro Ranellucci
2011-08-26Added support for using different endstops ()lemio
2011-08-25Refactoring in M109 to support residency time on cooling without code ↵Alessandro Ranellucci
duplication
2011-08-11Adding falling mode to M109 to better implement GCode definitionNils
2011-08-03Merge pull request #65 from blddk/masterkliment
M42 for toggling individual pins or setting PWM, modified MINTEMP to apply to heated bed
2011-08-03Fixed so commenting out MINTEMP won't break compile, however, commenting out ↵blddk
MINTEMP will then again allow the bed to be turned on, but not off, when there are no thermistor, or thermistor is broken.
2011-08-03Added MINTEMP to work on the heated bed too, so it will also turn off when ↵blddk
thermistor fails.
2011-08-02Added M42 to control non used pins example: M42 P23 S255blddk
2011-08-02When you set PWM on a pin to a given value and then WRITE a 0 to it, the PWM ↵Kliment
timer does not stop. Set the PWM to 0 as well to prevent hotend meltdowns.
2011-07-26Merge pull request #62 from alexrj/heater-current-limitkliment
Heater current limit
2011-07-26New config option HEATER_CURRENT to limit current to the nozzleAlessandro Ranellucci
2011-07-26New implementation of TEMP_RESIDENCY_TIME. We now wait for the target temp ↵Alessandro Ranellucci
to be esablished and maintained for residency time +/- a configurable hysteresis
2011-07-25add support for TEMP_RESIDENCY_TIME for M109Lawrence Leung larryleungcal@yahoo.com
2011-07-24Merge branch 'experimental'kliment
2011-07-24Merge remote branch 'origin/experimental' into experimentalEmanuele Caruso
2011-07-24Fixed bug which in some cases caused the moves to be done at full speed ↵Emanuele Caruso
without acceleration
2011-07-24added uuid identification supportjglauche
2011-07-17Merge branch 'master' into experimentalkliment
2011-07-17Add extra config for homing feedrate - fixes #28kliment
2011-07-16Merge branch 'master' into experimentalkliment
generated by cgit v1.2.1 (git 2.18.0) at 2025-02-17 02:22:09 +0000