From cc089f4a4154f195a57afbf844ad3fb7a86ff754 Mon Sep 17 00:00:00 2001 From: Christopher Jansen Date: Tue, 3 May 2011 01:24:32 -0500 Subject: Added Makefile and declared required functions in .pde to support it working. Tested on various configs with arduinio-0022. Note you have to edit the first few lines of the Makefile to match your config. --- Tonokip_Firmware/Makefile | 245 ++++++++++++++++++++++++++++++++++ Tonokip_Firmware/Tonokip_Firmware.pde | 33 +++++ 2 files changed, 278 insertions(+) create mode 100644 Tonokip_Firmware/Makefile (limited to 'Tonokip_Firmware') diff --git a/Tonokip_Firmware/Makefile b/Tonokip_Firmware/Makefile new file mode 100644 index 0000000..d847f13 --- /dev/null +++ b/Tonokip_Firmware/Makefile @@ -0,0 +1,245 @@ +# Arduino 0011 Makefile +# Arduino adaptation by mellis, eighthave, oli.keller +# +# This makefile allows you to build sketches from the command line +# without the Arduino environment (or Java). +# +# Detailed instructions for using the makefile: +# +# 1. Copy this file into the folder with your sketch. There should be a +# file with the same name as the folder and with the extension .pde +# (e.g. foo.pde in the foo/ folder). +# +# 2. Modify the line containg "INSTALL_DIR" to point to the directory that +# contains the Arduino installation (for example, under Mac OS X, this +# might be /Applications/arduino-0012). +# +# 3. Modify the line containing "PORT" to refer to the filename +# representing the USB or serial connection to your Arduino board +# (e.g. PORT = /dev/tty.USB0). If the exact name of this file +# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*). +# +# 4. Set the line containing "MCU" to match your board's processor. +# Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth +# or Diecimila have the atmega168. If you're using a LilyPad Arduino, +# change F_CPU to 8000000. +# +# 5. At the command line, change to the directory containing your +# program's file and the makefile. +# +# 6. Type "make" and press enter to compile/verify your program. +# +# 7. Type "make upload", reset your Arduino board, and press enter to +# upload your program to the Arduino board. +# +# $Id$ + +TARGET = $(notdir $(CURDIR)) +INSTALL_DIR = /home/chris/arduino-0022 +UPLOAD_RATE = 38400 +AVRDUDE_PROGRAMMER = stk500v1 +PORT = /dev/ttyUSB0 +MCU = atmega644p +F_CPU = 16000000 + + +############################################################################ +# Below here nothing should be changed... + +ARDUINO = $(INSTALL_DIR)/hardware/arduino/cores/arduino +AVR_TOOLS_PATH = /usr/bin +SRC = $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \ +$(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \ +$(ARDUINO)/wiring_pulse.c $(ARDUINO)/wiring_serial.c \ +$(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c +CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \ +$(ARDUINO)/Print.cpp +FORMAT = ihex + + +# Name of this Makefile (used for "make depend"). +MAKEFILE = Makefile + +# Debugging format. +# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. +# AVR (extended) COFF requires stabs, plus an avr-objcopy run. +DEBUG = stabs + +OPT = s + +# Place -D or -U options here +CDEFS = -DF_CPU=$(F_CPU) +CXXDEFS = -DF_CPU=$(F_CPU) + +# Place -I options here +CINCS = -I$(ARDUINO) +CXXINCS = -I$(ARDUINO) + +# Compiler flag to set the C Standard level. +# c89 - "ANSI" C +# gnu89 - c89 plus GCC extensions +# c99 - ISO C99 standard (not yet fully implemented) +# gnu99 - c99 plus GCC extensions +CSTANDARD = -std=gnu99 +CDEBUG = -g$(DEBUG) +CWARN = -Wall -Wstrict-prototypes +CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums +#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) + +CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) +CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) +#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs +LDFLAGS = -lm + + +# Programming support using avrdude. Settings and variables. +AVRDUDE_PORT = $(PORT) +AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex +AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf \ +-p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ +-b $(UPLOAD_RATE) + +# Program settings +CC = $(AVR_TOOLS_PATH)/avr-gcc +CXX = $(AVR_TOOLS_PATH)/avr-g++ +OBJCOPY = $(AVR_TOOLS_PATH)/avr-objcopy +OBJDUMP = $(AVR_TOOLS_PATH)/avr-objdump +AR = $(AVR_TOOLS_PATH)/avr-ar +SIZE = $(AVR_TOOLS_PATH)/avr-size +NM = $(AVR_TOOLS_PATH)/avr-nm +AVRDUDE = $(AVR_TOOLS_PATH)/avrdude +REMOVE = rm -f +MV = mv -f + +# Define all object files. +OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) + +# Define all listing files. +LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) + +# Combine all necessary flags and optional flags. +# Add target processor to flags. +ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) +ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) +ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) + + +# Default target. +all: applet_files build sizeafter + +build: elf hex + +applet_files: $(TARGET).pde + # Here is the "preprocessing". + # It creates a .cpp file based with the same name as the .pde file. + # On top of the new .cpp file comes the WProgram.h header. + # At the end there is a generic main() function attached. + # Then the .cpp file will be compiled. Errors during compile will + # refer to this new, automatically generated, file. + # Not the original .pde file you actually edit... + test -d applet || mkdir applet + echo '#include "WProgram.h"' > applet/$(TARGET).cpp + cat $(TARGET).pde >> applet/$(TARGET).cpp + cat $(ARDUINO)/main.cxx >> applet/$(TARGET).cpp + +elf: applet/$(TARGET).elf +hex: applet/$(TARGET).hex +eep: applet/$(TARGET).eep +lss: applet/$(TARGET).lss +sym: applet/$(TARGET).sym + +# Program the device. +upload: applet/$(TARGET).hex + $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) + + + # Display size of file. +HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex +ELFSIZE = $(SIZE) applet/$(TARGET).elf +sizebefore: + @if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi + +sizeafter: + @if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi + + +# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. +COFFCONVERT=$(OBJCOPY) --debugging \ +--change-section-address .data-0x800000 \ +--change-section-address .bss-0x800000 \ +--change-section-address .noinit-0x800000 \ +--change-section-address .eeprom-0x810000 + + +coff: applet/$(TARGET).elf + $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof + + +extcoff: $(TARGET).elf + $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof + + +.SUFFIXES: .elf .hex .eep .lss .sym + +.elf.hex: + $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ + +.elf.eep: + -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ + --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ + +# Create extended listing file from ELF output file. +.elf.lss: + $(OBJDUMP) -h -S $< > $@ + +# Create a symbol table from ELF output file. +.elf.sym: + $(NM) -n $< > $@ + + # Link: create ELF output file from library. +applet/$(TARGET).elf: $(TARGET).pde applet/core.a + $(CC) $(ALL_CFLAGS) -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS) + +applet/core.a: $(OBJ) + @for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done + + + +# Compile: create object files from C++ source files. +.cpp.o: + $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ + +# Compile: create object files from C source files. +.c.o: + $(CC) -c $(ALL_CFLAGS) $< -o $@ + + +# Compile: create assembler files from C source files. +.c.s: + $(CC) -S $(ALL_CFLAGS) $< -o $@ + + +# Assemble: create object files from assembler source files. +.S.o: + $(CC) -c $(ALL_ASFLAGS) $< -o $@ + + + +# Target: clean project. +clean: + $(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \ + applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \ + $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) + +depend: + if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ + then \ + sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ + $(MAKEFILE).$$$$ && \ + $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ + fi + echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ + >> $(MAKEFILE); \ + $(CC) -M -mmcu=$(MCU) $(CDEFS) $(CINCS) $(SRC) $(ASRC) >> $(MAKEFILE) + +.PHONY: all build elf hex eep lss sym program coff extcoff clean depend applet_files sizebefore sizeafter diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde index 87935c1..508becf 100644 --- a/Tonokip_Firmware/Tonokip_Firmware.pde +++ b/Tonokip_Firmware/Tonokip_Firmware.pde @@ -8,6 +8,39 @@ #include "SdFat.h" #endif +void get_command(); +void process_commands(); + +void manage_inactivity(byte debug); + +void manage_heater(); +float temp2analog(int celsius); +float temp2analogBed(int celsius); +float analog2temp(int raw); +float analog2tempBed(int raw); + +void FlushSerialRequestResend(); +void ClearToSend(); + +void get_coordinates(); +void linear_move(unsigned long x_steps_remaining, unsigned long y_steps_remaining, unsigned long z_steps_remaining, unsigned long e_steps_remaining); +void disable_x(); +void disable_y(); +void disable_z(); +void disable_e(); +void enable_x(); +void enable_y(); +void enable_z(); +void enable_e(); +void do_x_step(); +void do_y_step(); +void do_z_step(); +void do_e_step(); + +void kill(byte debug); + + + // look here for descriptions of gcodes: http://linuxcnc.org/handbook/gcode/g-code.html // http://objects.reprap.org/wiki/Mendel_User_Manual:_RepRapGCodes -- cgit v1.2.1