| Age | Commit message (Collapse) | Author |
|---|
|
* The hello protocol monitors connectivity in 2 different ways:
a) local -> remote
b) remote -> local
Connectivity is required in both directions (2-way) for adjacencies to
form.
The first requires a round-trip to detect, and is done by advertising
which other hosts a router knows about in its hello messages. This allows
a host to detect which other routers are and are not receiving its
message. If a remote neighbour delists the local router, then the local
router raises a "1-Way Received" event.
The latter is straight-forward, and is detected by setting a timer for the
neighbour. If another Hello packet is not received within this time then
the neighbour is dead, and a separate "Inactive" event is raised.
These are 2 different and relatively independent measures.
Knowing that we can optimise the 2nd, remote->local measure and reset
the timer when /any/ packet arrives from that neighbour. For any packet
is as good as a Hello packet. This can help in marginal situations, where
the number of protocol messages that must be sent sometimes can exceed
the capacity of the network to transmit the messages within the configured
dead-time. I.e. an OSPF network with lots of LSAs, slow links and/or
slow hosts (e.g. O(10k) LSAs, O(100kbit) links, embedded CPUs, and O(10s)
dead-times).
This optimisation allows an OSPF network to run closer to this margin,
and/or allows networks to perhaps better cope with rare periods of
exceptional load, where otherwise they would not.
It's fully compatible with plain OSPF implementations and doesn't
prejudice dead-neighbour detection.
* ospf_nsm.h: Rename HelloReceived event to PacketReceived.
* ospf_nsm.c: (nsm_hello_received) -> nsm_packet_received
* ospf_packet.c: Schedule PacketReceived whenever a valid message is
received.
|
|
|
|
* ospf_ase.c: (ospf_ase_calculate_route) Fix compiler warning about eval
needing brackets.
(various) add defensive asserts.
* ospf_lsdb.c: (ospf_lsdb_add) add missing node unlock if same lsa already
was indexed.
(ospf_lsdb_delete) check it's actually the same as specified lsa before
deleting
(ospf_lsdb_lookup_by_id_next) fix another corner case - no result =>
don't go on.
|
|
* ospf_lsa.c: (ospf_lsa_refresh_walker) fix an "unlock before use" bug
(various) add asserts for lsa refcounting.
|
|
* ospf_interface.c: (ospf_if_{new,cleanup}) don't touch the network_lsa_self,
ISM and NSM take care of cleaning it up if needs be + we want to keep
network_lsa_self around when possible for the the seqnum.
This shouldn't really make much difference though, particularly as we have
a separate sequence number memory mechanism.
|
|
* ospf_packet.c: (ospf_ls_upd) the corresponding test on the arrival side
in (ospf_flood) is <, so this should be >=, not >, purely for consistency.
There is no practical effect here though.
|
|
* ospf_interface.c: (ospf_if_free) events with dangling pointers left
scheduled can be seriously bad for ospfd's health. Cancel the event.
|
|
* ospf_{ism,network}.c: Certain oft-repeated but trivial messages should be
debug log level, not info, to avoid spamming 'terminal monitor'
|
|
* lib/table.c: (route_node_match) fix overshoot that was causing this
function to go 1 bit too far and thus reading past end of prefix.
(route_node_lookup) be defensive - don't assume others will clean up
leaves when removing info.
|
|
* lib/prefix.c: (prefix_match) nano-optimisation, let it return early
without copying pointers.
|
|
* workqueue.c: (work_queue_run) Err more on the side of keeping granularity
down, by being more conservative about increasing it.
Also, fix mispelling.
|
|
* (general) this can be useful when investigating thread latency problems,
when you don't want to have to restart a daemon between tests.
* thread.c: (cpu_record_(hash_)clear) wipe the stored thread cpu history
data, according to the filter, similar to the vty print code.
(clear_thread_cpu_cmd) new command to clear data.
* thread.h: export new command
* command.c: install it
|
|
* thread.c: (thread_fetch) the current scheduler will service events
indefinitely, ignoring I/O and timers, so long as there are events.
In other words, events can crowd out I/O and timers. In theory this
shouldn't be a huge problem as events are generated only by timers
and I/O, however in practice it means normal-load behaviour is not as
useful a predictor of high-load behaviour as it should be.
Fix this by considering all the kinds of threads, in every run of the
scheduler. For any given run, we prioritise events, however across
runs the scheduler should be fair.
This has been observed to give more stable inter-packet times in
testing of ospfd (i.e. lower std-dev).
(thread_process) new heler to queue all the given threads onto the ready
list
|
|
* thread.h: (struct cpu_thread_history.funcname) malloc gets called on this
so it should not be const
* thread.c: (cpu_record_print) cast the (const char *) to (char *), this
function knows what it's doing (free wont be called on it).
|
|
* bgp_route.c: (bgp_process_queue_init) rsclient wasn't getting all the
same things initialised as the main queue. Simplify to make it more robust.
|
|
* HACKING: Express notion that a published git repository is
preferred. Fold request for commit message into patch section.
Express desire for comments in code explaining correctness of
post-commit state, and for commit message to explain correctness of
the change.
|
|
HACKING: Whitespace changes only.
|
|
Note 54/72 line length rules, and that this is intended to play nice
with "git log --oneline".
|
|
Tom's repo is now a clone of the official repo and has an mttr branch
off of 0.99.17.
|
|
* bgp_route.c: (route_vty_out_detail) calculate time value
in a way, which works regardless of monotonic clock
being used or not
|
|
If router-id is not specified in ospf6d.conf, ospf6d will get it from
the zebra daemon. But ospf6d originates Link LSAs before the router-id
is returned by zebra, thus this router's Link LSAs will be flooded
with AdvRouter set to 0.
* zclient.c: zclient_start(): send ZEBRA_INTERFACE_ADD message after
ZEBRA_ROUTER_ID_ADD, not before
|
|
* bgpd/bgp_attr.c, bgpd/bgp_open.h, bgpd/bgp_route.c, lib/prefix.c,
lib/prefix.h: Various integer types were being used where, if we
had strict type checking, afi_t and safi_t would be required.
Signed-off-by: G.Balaji <balajig81@gmail.com>
(cherry picked from commit c8af35ffa2dc79ff7d7ff00b1b61f1f50a100ab6)
|
|
|
|
Signed-off-by: G.Balaji <balajig81@gmail.com>
|
|
lib/memory.c:z{a,c,re}alloc, zfree, zdup: add requires/effects
comments.
|
|
Balaji has been accumulating patches from the mailing list and
pre-screening them and spiffing up commit messages.
|
|
bgpd/bgp_packet.c:bgp_update_packet(): When extracting the peer, don't
fail to extract it because "binfo->extra" is NULL. While one should
certainly avoid dereferencing binfo->extra, that's not a good reason
not to use binfo->peer.
Fixes https://bugzilla.quagga.net/show_bug.cgi?id=497.
Patch by Eric Sobocinksi.
|
|
This looks like a bug in original code from misunderstanding
of C rules of evaluation.
|
|
* configure.ac: bump up version number
|
|
* bgpd/bgp_aspath.c
* assegments_parse(): add handling of AS4_PATH input, update bounds
checks, add check for AS segment type
* aspath_parse(): add handling of AS4_PATH input, expect
assegments_parse() to do length checking
* aspath_empty(): update for the new function prototype
* bgpd/bgp_aspath.h: ditto
* tests/aspath_test.c: ditto
* bgpd/bgp_attr.c
* bgp_attr_aspath(): add handling of AS4_PATH input, update flags
checks, change returned type
* bgp_attr_as4_path(): discard, superseded by bgp_attr_aspath()
* bgp_attr_parse(): update respectively
|
|
* bgp_packet.c: (bgp_route_refresh_receive) add validation of
"Length" (RFC5292) field value, check input stream bounds
each time bytes are pulled from it
|
|
When deleting a VLAN interface after flushing its
addresses, zebra uses 100% CPU time and freezes.
* interface.c: The while loop in line 407 that
should clean up connected routes never hits one
of the 2 lines "last = node;" and thus loops
forever.
Signed-off-by: Roman Hoog Antink <rha@open.ch>
|
|
|
|
these are autogenerated by autoreconf, drop them from git.
|
|
this fixes warnings from vtysh extract.pl by making sure the isis method
files always 'work'. (previously, extract.pl would grab unselected isis
method sources and then complain about missing headers)
|
|
startup-config
* ospf6_interface.c: When '[no] ipv6 ospf6 advertise prefix-list'
appears in the startup configuration for ospf6d, a crash occurs,
because ospf6d attempts to schedule LSAs when the 'oi->area'
structure has not yet been initialized.
Now, when the command above is issued (either in the startup
configuration or at runtime), ospf6d will only schedule LSAs if
the 'oi->area' structure has been initalized. A similar test is
already used when handling the commands 'ipv6 ospf6 priority'
and 'ipv6 ospf6 cost'.
|
|
|
|
* ospf_zebra.c: (ospf_distribute_list_update_timer) forces a
refresh of default route each time it finds a default prefix.
This is suboptimal, just record that it needs to be done and
do it once.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
* ospf_zebra.c: (ospf_distribute_list_update_timer)
If there are updates to the distribute list every 5 second or less,
ospf_distribute_list_update_timer() will never run as the timer gets
rearmed for each update. This fixes it by never rearming an active
distribute list timer.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
Roman Hoog Antink <rha@open.ch> reports:
When adding a connected route (using vtysh, without restart) to the
redistribution access list of ospfd, while static routes already exist,
the update timer ospf_distribute_list_update_timer() is being run for
static routes only. That way, the connected route never appears in the
OSPF database, until quagga is completely restarted.
The update timer for connected routes is cancelled in
ospfd/ospfd_zebra.c:ospf_distribute_list_update():976, were a new timer
is scheduled for static routes, caused by the loop in ospf_filter_update().
* ospf_zebra.c: (ospf_distribute_list_update_timer) make it
refresh all external routes. This fixes the problem
reported by Roman.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
* (HACKING.pending): List known places where work on quagga that is
not (yet) integrated into the main tree can be found.
|
|
|
|
|
|
|
|
* configure.ac: bump up version number
|
|
Stephen:
A recent change breaks build Quagga on Debian Lenny with amd64 (but not
i386). Not sure whether this is cause by ld, gcc, or libtool; but
whatever it just won't work for a large number of users.
Mathias:
I would guess it's a problem of libtool because it adds "-fPIC -DPIC" to
the compiler flags but doesn't remove -fPIE. That wouldn't be a problem
if the compiler would ignore the -fPIE in favor to the latter -fPIC, but
obviously it does not. [...] Those objects were actually compiled with
-fPIC but also -fPIE which seems to confuse gcc.
|
|
Because the final executables are built as position independent
executables (PIE) -- when configure has detected compiler supported for
PIE -- the objects in the library archive must be built in that way,
too. Otherwise the runtime linker has to do unneccesary relocation for
each start of the program. Even worse, the programs won't even be able
to start on a (hardened) kernel that doesn't allow those relocations to
happen by preventing making the .text segment writable (PaX's MPROTECT
feature comes to mind). The attached patch fixes this issue by adding
the appropriate flags to the Makefile.am.
|
|
BGP uses time() to get system time of day; but that value
fluctuates with time adjustments from NTP. This can cause premature
flapping of peer sessions and other failures.
Use the system monotonic clock supported by Quagga thread library
to avoid issue.
See: http://bugzilla.vyatta.com/show_bug.cgi?id=4467
* bgpd/bgp_fsm.c
* bgp_uptime_reset(): dismiss function
* bgpd/bgpd.c
* bgp_clock(): new function
* bgpd/bgp_damp.c
* bgp_reuse_timer(): employ bgp_clock() instead of time(NULL)
* bgp_damp_withdraw(): idem
* bgp_damp_update(): idem
* bgp_damp_scan(): idem
* bgp_damp_info_vty(): idem
* bgp_damp_reuse_time_vty(): idem
* bgpd/bgp_fsm.c
* bgp_routeadv_timer(): idem
* bgp_stop(): idem
* bgp_establish(): idem
* bgpd/bgp_packet.c
* bgp_update_receive(): idem
* bgpd/bgp_route.c
* bgp_update_rsclient(): idem
* bgp_update_main(): idem
* bgp_static_update_rsclient(): idem
* bgp_static_update_main(): idem
* bgp_static_update_vpnv4(): idem
* bgp_aggregate_route(): idem
* bgp_aggregate_add(): idem
* bgp_redistribute_add(): idem
* bgpd/bgp_snmp.c
* bgpPeerTable(): idem
* bgpTrapEstablished(): idem
* bgpTrapBackwardTransition(): idem
* bgpd/bgpd.c
* peer_create(): idem
* peer_uptime(): idem
* bgp_master_init(): idem
|
|
* ospf_packet.c: (ospf_ls_upd) DISCARD_LSA continues, and so should be
after debug messages, not before them.
|
|
* ospf_lsdb.c: (lsdb_prefix_set) memset is unneeded, as all fields are
initialised explicitly, and this function can be in the top-3 of a
profile when there are a lot of LSAs.
|
