| Age | Commit message (Collapse) | Author |
|---|
|
* lib/thread.h: new timer macro, millisecond precision
(this was cherrypicked from pimd to isolate all non-contained changes)
From: Everton Marques <everton.marques@gmail.com>
Signed-off-by: David Lamparter <equinox@diac24.net>
|
|
* Replace command "isis passwd" with "isis passwd {clear|md5}"
* Verify HMAC MD5 on ISIS Hello PDUs
* Add HMAC MD5 authentication to md5.h/md5.c from RFC2104
|
|
Fix bug 544: isisd produces an unexpected routing table for wide-metric.
* isis_spf.c: Accept VTYPE_PSEUDO_TE_IS and VTYPE_NONPSEUDO_TE_IS
vertex types for SPF calculation
* isis_pdu.c: Change order of TLVs to match Cisco to make bitwise
comparison easier for Wireshark
* isis_tlv.c: EXTREME_TLV_DEBUG for TLV debugging instead of
EXTREME_DEBUG
|
|
The forwarding table was filled with wrong next-hops, and which is even
worse, it was done in a totally non-deterministic way.
The next-hop set for an IP prefix by isisd was the neighbor IS from
which the flooded LSP about the IP prefix was arrived. So, if an IS
received all the LSPs through its, say, eth0 interface, all entries
in the forwarding table contained the next IS reachable via eth0 as
the next-hop.
The solution is to propagate the correct next-hop further from node to
node as the SPF algorithm traverses the graph and selects the next
node to be added to the set of already covered nodes.
Also, the construction of the tentative node list (the nodes where the
shortest path is not known yet) was buggy: if a node was already a
member of this list with a certain path cost, and an alternative path
was found to it with a lower cost while processing a pseudo-node LSP,
it was not added to the list. This way, the path selected by isisd for
a certain prefix was the first one it encountered during the LSDB
processing.
Signed-off-by: Fritz Reichmann <fritz@reichmann.nl>
|
|
After an IS has been elected as the Designated IS for a LAN, it did
not refresh the content of the pseudo-node after a new node has been
connected to the same LAN. Instead, the periodically reoriginated
pseudo-node LSP still contained only those IS neighbors that were
already present when the DIS election process was commenced.
The fix for the problem schedules an LSP regeneration rather than
just reoriginating the same LSP with the old content.
Signed-off-by: Fritz Reichmann <fritz@reichmann.nl>
|
|
isisd has a so-called circuit state machine that takes care about
the interface state changes, such as initializing, down, up. When
an interface was brought down by a link failure, the interface
information was deleted and set to NULL. When the link was restored
later, the interface was looked up by the old pointer, but since it
was cleared, it was never found again, resulting in an interface
never entering the up state again.
Also, the program regularly crashed because of a deleted pointer in
the same context which was later accessed without any further
checking.
Signed-off-by: Fritz Reichmann <fritz@reichmann.nl>
|
|
ospf6_prefix_apply_mask would write one byte beyond the 4/8/12
bytes allocated for prefixes of length 32/64/96.
based on report and patch by Jon Andersson <jon.andersson@thales.no>
Reported-by: Jon Andersson <jon.andersson@thales.no>
Signed-off-by: David Lamparter <equinox@diac24.net>
|
|
ipv6 nd ra-interval
ipv6 nd ra-lifetime
ipv6 nd reachable-time
ipv6 nd home-agent-preference
ipv6 nd home-agent-lifetime
ipv6 nd router-preference
Calls to atoi() and atol() are replaced with VTY_GET_INTEGER_RANGE()
macro, command patterns are clarified and aliases of some commands
are added for consistency. Other changes are listed below.
* zebra/rtadv.c
* ipv6_nd_ra_interval_msec(): resolve -Wsign-compare
* ipv6_nd_ra_interval(): idem
* rtadv_init(): update to list new aliases
* doc/ipv6.texi: update to match current implementation
|
|
RFC2461 was replaced by RFC4861
RFC3775 was replaced by RFC6275
draft-ietf-mip6-mipext-advapi-03 was replaced by RFC4584
|
|
rtadv_prefix.prefix was casted to "struct prefix_ipv6" and had the same
size, make it exactly this type to make the code a bit cleaner.
|
|
RFC4861 4.6.2. Prefix Information
Prefix An IP address or a prefix of an IP address. The
Prefix Length field contains the number of valid
leading bits in the prefix. The bits in the prefix
after the prefix length are reserved and MUST be
initialized to zero by the sender and ignored by
the receiver.
* rtadv.c
* ipv6_nd_prefix(): add missing call to apply_mask_ipv6()
* no_ipv6_nd_prefix(): idem
|
|
There was a regression introduced with the previous commit:
"ipv6 nd home-agent-lifetime 1800000" appeared by default in every
interface section of running-config, although this command is
invalid in this context. Troubleshooting and bugfixing of the issue
tracked out several bugs in router advertisement procedures, some of
which are fixed in this commit.
* zebra/interface.c
* if_zebra_new_hook(): update to treat -1 as "uninitialized"
* nd_dump_vty(): idem
* zebra/rtadv.c
* rtadv_send_packet(): update processing of "router lifetime" field,
"home agent" option and "home agent lifetime" field to conform to
RFC6275 better
* ipv6_nd_ra_interval_msec(): update MaxRtrAdvInterval range check,
make sure it never exceeds (initialized) AdvDefaultLifetime
* ipv6_nd_ra_interval(): idem
* ipv6_nd_ra_lifetime(): update AdvDefaultLifetime range check, make
sure it never falls below MaxRtrAdvInterval
* ipv6_nd_homeagent_lifetime(): update HomeAgentLifetime range check
* no_ipv6_nd_ra_lifetime(): update to treat -1 as "uninitialized"
* no_ipv6_nd_homeagent_lifetime(): idem
* rtadv_config_write(): idem
|
|
The following options could be configured for an interface, but were
never visible in the config text:
ipv6 nd adv-interval-option
ipv6 nd home-agent-preference
ipv6 nd home-agent-lifetime
ipv6 nd home-agent-config-flag
|
|
The previous commits modified both zebra and bgpd for additional
SAFI field, but not any other routing daemon, which led to zebra
daemon crashing with failed assertion.
|
|
|
|
warning: too many arguments for format [-Wformat-extra-args]
|
|
The patch adds the ipv6 network command in the BGP multicast address
family mode.
|
|
This patch contains the following:
1. Addition of IPv6 SAFI_MULTICAST BGP routes into the RTM's RIB.
2. Deletion of IPv6 SAFI_MULTICAST BGP routes from the RTM's RIB.
|
|
This patch contains the following:
1. Addition of IPv6 SAFI_MULTICAST BGP routes into the BGP Multicast RIB.
2. Deletion of IPv6 SAFI_MULTICAST BGP routes from the BGP Multicast RIB.
|
|
This patch contains the following:
1. Addition of IPv4 SAFI_MULTICAST BGP routes into the RTM's RIB.
2. Deletion of IPv4 SAFI_MULTICAST BGP routes from the RTM's RIB.
|
|
This patch contains the following:
1. Addition of IPv4 SAFI_MULTICAST BGP routes into the BGP Multicast RIB.
2. Deletion of IPv4 SAFI_MULTICAST BGP routes from the BGP Multicast RIB.
|
|
This implements a new "ipv6 nd mtu <1-65535>" interface-level command.
* doc/ipv6.texi: add description
* zebra/rtadv.c
* rtadv_send_packet(): send option type 5, when configured
* ipv6_nd_mtu(): new VTY helper
* no_ipv6_nd_mtu(): ditto
* rtadv_config_write(): add new option
* rtadv_init(): list new helpers
|
|
* bgp_nexthop.c: The nexthop lookup cache has to return success for queried
nexthops if bgpd isn't connected to zebra, or else BGP without zebra doesn't
work.
|
|
This marker merge (i.e. an 'ours' strategy merge) is a placeholder to show
that all commits in Quagga-RE stable, to its release RE-0.99.17.6 tag, have
been reviewed and merged into 'master'.
|
|
|
|
* bgpd/bgp_attr.c: (bgp_attr_aspath) error message could be misleading,
clearly log what flag was incorrect.
(Problem noted in "bgpd: fix error message in bgp_attr_aspath()" in
Quagga-RE)
|
|
|
|
|
|
* bgp_attr.c
* attr_flag_str: new message list
* bgp_attr_flags_diagnose(): new function, implements previously added
error logging in a generic way
* bgp_attr_origin(): use bgp_attr_flags_diagnose()
* bgp_attr_nexthop(): ditto
* bgp_attr_med(): ditto
* bgp_attr_local_pref(): ditto
* bgp_attr_atomic(): ditto
* bgp_attr_originator_id(): ditto
* bgp_attr_cluster_list(): ditto
* bgp_mp_reach_parse(): ditto
* bgp_mp_unreach_parse(): ditto
|
|
|
|
The function is implemented in ospf_lsa.c, move its "extern" declaration
to ospf_lsa.h for consistency.
|
|
* ospf_ase.c
* ospf_ase_complete_direct_routes(): dismiss unused variable
|
|
|
|
* bgp_nexthop.c (show_ip_bgp_scan_tables): access proper structure field
in AF_INET6 case, handle ifindex NH type properly
|
|
bgp_nexthop_onlink(): zlookup is not used here at all
bgp_nexthop_lookup_ipv6(): rely on the detection performed by "query"
function (this also changes the fallback value to 0), reorder if-block
bgp_nexthop_lookup(): idem
|
|
* bgp_nexthop.c: (show_ip_bgp_scan) transform into
show_ip_bgp_scan_tables(), which uses inet_ntop() and can dump
nexthops on request; (show_ip_bgp_scan_detail_cmd) new function
|
|
bgp_nexthop_lookup_ipv6(): declare variables where they are actually
used, drop no-op initialization (the field is already 0)
bgp_nexthop_lookup(): ditto
bgp_nexthop_check_ebgp(): rename to bgp_nexthop_onlink()
bgp_nexthop_cache_changed(): rename to bgp_nexthop_cache_different()
|
|
* if.c: (if_dump) loop that doesn't do anything, wants to be
before the zlog of what it's meant to print out so all the connected
addresses get printed out. Trival: just a debug function
|
|
* (general) Move functions in headers into files, to be compiled into
shared object files. Remove inline qualifier from functions. Let the
compiler do the work.
|
|
|
|
|
|
|
|
When the same ip address is used on several interfaces,
and one of them gets deleted (or equivalent: set to down and
then address removed), rib_delete_ipv[46] will also remove
the connected route from other interfaces.
rib_delete_ipv[46] is called twice when an interface is
deleted:
- for the "ifdown" event
- for the address removal
(note: this may be specific to the netlink interface of linux)
The second call does not find the connected route to that same
ifindex anymore, but deletes similar connected routes to any
other ifindex instead.
Reason: the ifindex check is on the same level as the check
for ZEBRA_ROUTE_CONNECT/NEXTHOP_TYPE_IFINDEX. If everything
matches except for the ifindex, the "else" part (intended for
different route types) is executed, thus removing the route
from the wrong interface.
fix: move ifindex check inside the "then" part of the check
for ZEBRA_ROUTE_CONNECT/NEXTHOP_TYPE_IFINDEX. Now connected
routes to other ifindexes will not spill over to the "else"
part for different route types anymore.
|
|
* fix disagreement with C99 in zlog_debug calls
Format specifier in some zlog_debug calls for size_t values
was changed in order to C99 ('%u' -> '%zu').
* fix -Wsign-compare warnings
Type of return value of ospf6_packet_max() was changed.
|
|
...otherwise 4294967295 is not a valid value on 32bit systems
|
|
* ospf6_route.c: (ospf6_route_best_next) Allows unlock route, even
when there's no next route. This is consistent with how
ospf6_route_next() behaves.
* ospf6_intra.c: (ospf6_intra_prefix_lsa_remove) Make sure the last
route considered is always unlocked. This is needed when the for
loop terminates because ospf6_route_is_prefix() returns zero.
Signed-off-by: Vyacheslav Trushkin <me@dogonthesun.net>
|
|
A clean exit makes it easier to use memory debuggers.
* ospf6_asbr.c: (ospf6_asbr_terminate) Add a function to do route map
cleanup.
* ospf6_lsa.c: (ospf6_lsa_terminate) Add a function to cleanup the lsa
handler vector.
* ospf6_main.c: (ospf6_exit) Add an function that causes ospf6d to
gracefully exit.
* ospf6_message.c: (ospf6_message_terminate) Add a function that frees
the send and receive buffers.
* ospf6_top.c: (ospf6_delete) Enable the ospf6_delete() function.
Disable ospf6 before freeing everything.
Signed-off-by: Vyacheslav Trushkin <me@dogonthesun.net>
Conflicts:
ospf6d/ospf6_lsa.h
|
|
if.c: (if_terminate) This adds a cleanup function that can be called
when a daemon exits, similar to vty_terminate().
|
|
|
|
|
