| Age | Commit message (Collapse) | Author |
|---|
|
2006-12-12 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* if.h: (struct connected) Add new ZEBRA_IFA_PEER flag indicating
whether a peer address has been configured. Comment now shows
the new interpretation of the destination addr: if ZEBRA_IFA_PEER
is set, then it must contain the destination address, otherwise
it may contain the broadcast address or be NULL.
(CONNECTED_DEST_HOST,CONNECTED_POINTOPOINT_HOST) Remove obsolete
macros that were specific to IPv4 and not fully general.
(CONNECTED_PEER) New macro to check ZEBRA_IFA_PEER flag.
(CONNECTED_PREFIX) New macro giving the prefix to insert into
the RIB: if CONNECTED_PEER, then use the destination (peer) address,
else use the address field.
(CONNECTED_ID) New macro to come up with an identifying address
for the struct connected.
* if.c: (if_lookup_address, connected_lookup_address) Streamline
logic with new CONNECTED_PREFIX macro.
* prefix.h: (PREFIX_COPY_IPV4, PREFIX_COPY_IPV6) New macros
for better performance than the general prefix_copy function.
* zclient.c: (zebra_interface_address_read) For non-null destination
addresses, set prefixlen to equal the address prefixlen. This
is needed to get the new CONNECTED_PREFIX macro to work properly.
* connected.c: (connected_up_ipv4, connected_down_ipv4,
connected_up_ipv6, connected_down_ipv6) Simplify logic using the
new CONNECTED_PREFIX macro.
(connected_add_ipv4) Set prefixlen in destination addresses (required
by the CONNECTED_PREFIX macro). Use CONNECTED_PEER macro instead
of testing for IFF_POINTOPOINT. Delete invalid warning message.
Warn about cases where the ZEBRA_IFA_PEER is set but no
destination address has been supplied (and turn off the flag).
(connected_add_ipv6) Add new flags argument so callers may set
the ZEBRA_IFA_PEER flag. If peer/broadcast address satisfies
IN6_IS_ADDR_UNSPECIFIED, then reject it with a warning.
Set prefixlen in destination address so CONNECTED_PREFIX will work.
* connected.h: (connected_add_ipv6) Add new flags argument so
callers may set the ZEBRA_IFA_PEER flag.
* interface.c: (connected_dump_vty) Use CONNECTED_PEER macro
to decide whether the destination address is a peer or broadcast
address (instead of checking IFF_BROADCAST and IFF_POINTOPOINT).
* if_ioctl.c: (if_getaddrs) Instead of setting a peer address
only when the IFF_POINTOPOINT is set, we now accept a peer
address whenever it is available and not the same as the local
address. Otherwise (no peer address assigned), we check
for a broadcast address (regardless of the IFF_BROADCAST flag).
And must now pass a flags value of ZEBRA_IFA_PEER to
connected_add_ipv4 when a peer address is assigned.
The same new logic is used with the IPv6 code as well (and we
pass the new flags argument to connected_add_ipv6).
(if_get_addr) Do not bother to check IFF_POINTOPOINT: just
issue the SIOCGIFDSTADDR ioctl and see if we get back
a peer address not matching the local address (and set
the ZEBRA_IFA_PEER in that case). If there's no peer address,
try to grab SIOCGIFBRDADDR regardless of whether IFF_BROADCAST is set.
* if_ioctl_solaris.c: (if_get_addr) Just try the SIOCGLIFDSTADDR ioctl
without bothering to check the IFF_POINTOPOINT flag. And if
no peer address was found, just try the SIOCGLIFBRDADDR ioctl
without checking the IFF_BROADCAST flag. Call connected_add_ipv4
and connected_add_ipv6 with appropriate flags.
* if_proc.c: (ifaddr_proc_ipv6) Must pass new flags argument to
connected_add_ipv6.
* kernel_socket.c: (ifam_read) Must pass new flags argument to
connected_add_ipv6.
* rt_netlink.c: (netlink_interface_addr) Copy logic from iproute2
to determine local and possible peer address (so there's no longer
a test for IFF_POINTOPOINT). Set ZEBRA_IFA_PEER flag appropriately.
Pass new flags argument to connected_add_ipv6.
(netlink_address) Test !CONNECTED_PEER instead of if_is_broadcast
to determine whether the connected destination address is a
broadcast address.
* bgp_nexthop.c: (bgp_connected_add, bgp_connected_delete)
Simplify logic by using new CONNECTED_PREFIX macro.
* ospf_interface.c: (ospf_if_is_configured, ospf_if_lookup_by_prefix,
ospf_if_lookup_recv_if) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_lsa.c: (lsa_link_ptop_set) Using the new CONNECTED_PREFIX
macro, both options collapse into the same code.
* ospf_snmp.c: (ospf_snmp_if_update) Simplify logic using new
CONNECTED_ID macro.
(ospf_snmp_is_if_have_addr) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_vty.c: (show_ip_ospf_interface_sub) Use new CONNECTED_PEER macro
instead of testing the IFF_POINTOPOINT flag.
* ospfd.c: (ospf_network_match_iface) Use new CONNECTED_PEER macro
instead of testing with if_is_pointopoint. And add commented-out
code to implement alternative (in my opinion) more elegant behavior
that has no special-case treatment for PtP addresses.
(ospf_network_run) Use new CONNECTED_ID macro to simplify logic.
* rip_interface.c: (rip_interface_multicast_set) Use new CONNECTED_ID
macro to simplify logic.
(rip_request_interface_send) Fix minor bug: ipv4_broadcast_addr does
not give a useful result if prefixlen is 32 (we require a peer
address in such cases).
* ripd.c: (rip_update_interface) Fix same bug as above.
|
|
2006-12-08 Paul Jakma <paul.jakma@sun.com>
* configure.ac: Bump to 0.99.6
|
|
2006-12-08 Hannes Gredler <hannes@gredler.at>
* isis_adjacency.c: (isis_new_adj) Allow NULL snpa argument.
* isis_pdu.c: (various) Update calls to isis_new_adj() to pass
NULL and use default.
* (general) Add forward declarations where required.
Fix up const char *'s.
Allow V4-only compilation.
|
|
2006-12-08 Piotr Chytla <pch@packetconsulting.pl>
* zebra_rib.c: (static_install_ipv{4,6}) Case where existing
RIB is updated must explicitely rib_addqueue the route_node,
to ensure the update actually takes effect.
|
|
2006-12-07 Paul Jakma <paul.jakma@sun.com>
* bgp_fsm.c: Bug #302 fix, diagnosis, suggestions and testing
by Juergen Kammer <j.kammer@eurodata.de>. Fix follows from
his suggested fix, just made in a slightly different way.
(bgp_event) Transitions into Clearing always must call
bgp_clear_route_all().
(bgp_stop) No need to clear routes here, BGP FSM should do
it.
|
|
2006-12-04 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospfd.c: (ospf_network_run) Remove an offending 'break' statement.
Previously, after creating a single ospf_interface on a given
network interface, the code would skip to the next interface
without considering other connected addresses on the interface.
After removing the 'break', we now consider all connected addresses.
|
|
2006-11-30 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* bgp_debug.h: Declare new bgp_debug_zebra conf and term flags,
and define BGP_DEBUG_ZEBRA.
* bgp_debug.c: Declare conf_bgp_debug_zebra and term_bgp_debug_zebra.
(debug_bgp_zebra, no_debug_bgp_zebra, undebug_bgp_zebra) New
functions to enable/disable bgp zebra debugging.
(no_debug_bgp_all) Turn off zebra debugging.
(show_debugging_bgp) Show whether zebra debugging is on.
(bgp_config_write_debug) Add 'debug bgp zebra' if configured.
(bgp_debug_init) Add new zebra debugging commands.
* bgp_zebra.c: (bgp_router_id_update, bgp_interface_add,
bgp_interface_delete, bgp_interface_up, bgp_interface_down,
bgp_interface_address_add, bgp_interface_address_delete,
zebra_read_ipv4, zebra_read_ipv6, bgp_zebra_announce,
bgp_zebra_withdraw, bgp_redistribute_set, bgp_redistribute_unset)
If zebra debugging is enabled, log an appropriate debug message.
|
|
2006-11-30 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_zebra.c: (ospf_router_id_update_zebra,
ospf_interface_address_add, ospf_interface_address_delete)
If (IS_DEBUG_OSPF (zebra, ZEBRA_INTERFACE)) is enabled, then
add a debug message about what Zebra is telling us.
(ospf_zebra_add_discard) Add a debug message matching the one
already in ospf_zebra_delete_discard.
|
|
2006-11-28 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* bgp_route.c: (bgp_info_restore) New function that undoes
the effects of a previous call to bgp_info_delete. This is
used when a route is deleted and quickly re-added before the
deletion has been processed.
(bgp_static_update_rsclient, bgp_static_update_main,
bgp_redistribute_add) Check whether a pre-existing route
has the BGP_INFO_REMOVED set, and, if so, we need to call
bgp_info_restore to resurrect it.
|
|
2006-11-28 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_vty.c: (ospf_passive_interface_default) Take additional
'newval' arg so we can update ospf->passive_interface_default inside
this function. More importantly, we now call ospf_if_set_multicast
on all ospf_interfaces.
(ospf_passive_interface, no_ospf_passive_interface) Fix bug:
for 'default' case, argv[0] is undefined, so we must test for
(argc == 0) before using argv[0]. And since
ospf_passive_interface_default now calls ospf_if_set_multicast as
needed, we can just return after calling
ospf_passive_interface_default.
|
|
2006-10-27 Paul Jakma <paul.jakma@sun.com>
* bgp_route.c: (bgp_table_stats) oops, u_intXX_t should be
uintXX_t
|
|
2006-10-24 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_zebra.c: (ospf_redistribute_default_set) Fix bug where
a new value for ospf->default_originate was being ignored
if a previous 'default-information originate' command
had already been processed.
|
|
2006-10-22 Yar Tikhiy <yar@comp.chem.msu.su>
* (general) Add support for passive-interface default (with
minor edits by Paul Jakma).
* ospf_interface.h: Add OSPF_IF_PASSIVE_STATUS macro, looking
at configured value, or the global 'default' value, as
required.
* ospf_interface.c: (ospf_if_new_hook) Leave passive
unconfigured per default, allowing global 'default' to
take effect for unconfigured interfaces.
* ospf_packet.c: (various) use OSPF_IF_PASSIVE_STATUS
* ospf_vty.c: (ospf_passive_interface_default) new function,
unset passive from all interfaces if default is enabled, as
the per-iface settings become redundant.
(ospf_passive_interface_update) new func, update passive
setting taking global default into account.
({no,}ospf_passive_interface_addr_cmd) Add support for
'default' variant of command.
(show_ip_ospf_interface_sub) Update to take global
default into account when printing passive status.
(ospf_config_write) ditto.
* ospfd.c: (ospf_new) set global passive-interface default.
* ospfd.h: (struct ospf) Add field for global
passive-interface.
|
|
2006-10-19 Paul Jakma <paul.jakma@sun.com>
* bgpd.c: (peer_new) bgp element of peer absolutely must be
filled in, make peer_new() require it as argument and update
all callers. Fixes a crash reported by Jan 'yanek' Bortl and
Andrew Schorr where bgpd would crash in bgp_pcount_adjust
trying to dereference the bgp member of bgp->peer_self,
triggered through redistribution.
* bgp_route.c: (bgp_pcount_adjust) assert sanity of arguments.
|
|
NULL pointer.
2006-10-15 Paul Jakma <paul.jakma@sun.com>
* bgp_packet.c: (bgp_update_packet) adv->rn can not be NULL,
check is bogus - changed to assert(), CID#64.
binfo is checked for NULL, but then dereferenced
unconditionally, fix, CID #63.
(bgp_withdraw_packet) Assert adv->rn is valid, as with
bgp_update_packet().
|
|
emtpy table
2006-10-15 Paul Jakma <paul.jakma@sun.com>
* bgp_route.c: (bgp_table_stats_walker) NULL deref if table is
empty, bgp_table_top may return NULL, Coverity CID#73.
|
|
stuck in Clearing.
2006-10-14 Paul Jakma <paul.jakma@sun.com>
* bgp_fsm.h: Remove BGP_EVENT_FLUSH_ADD, dangerous and not
needed.
* bgp_fsm.c: (bgp_stop) Move BGP_EVENT_FLUSH to the top of the
of the function, otherwise it could flush a ClearingCompleted
event, bug #302.
* bgp_packet.c: Replace all BGP_EVENT_FLUSH_ADD with
BGP_EVENT_ADD, fixing bug #302.
|
|
syntax
2006-10-04 Oliver Hookins <ohookins@gmail.com>
* bgpd/bgp_main.c: Add configuration check option, with
'-C' rather than '-c' for consistency between daemons.
* isisd/isis_main.c: ditto
* ospf6d/ospf6_main.c: ditto
* ospfd/ospf_main.c: ditto
* ripngd/ripng_main.c: ditto
* vtysh/vtysh_main.c: ditto
* ripd/rip_main.c: Change the config check option to
'-C' and tidy up the code.
* zebra/main.c: ditto
2006-10-04 Stergiakis Alexandros <astergiakis@antcor.com>
* ripd/rip_main.c: This trivial patch introduces a new
command-line option '-c', which instructs zebra/ripd
to check its configuration file for validity, print
any error message, and then exit. This is useful when
the configuration file is edited by hand or otherwise,
and you simply want to validate it without any other
effect.
* zebra/main.c: ditto
|
|
2006-10-14 Paul Jakma <paul.jakma@sun.com>
* if.c: (general) Handle upgrades from SUNWzebra, which tried
to track each logical interface as a seperate struct
interface, to Quagga, which assigns only one struct interface
per ifindex.
(if_sunwzebra_get) Try decompose a logical interface name
(fooX:Y) to the 'primary' name (fooX), for Solaris.
(interface_cmd) Use if_sunwzebra_get on Solaris.
|
|
2006-09-26 Pierre-Yves Ritschard <pierre-yves@spootnik.org>
* smux.c: (smux_open,smux_trap,smux_register) Fix various
asn_build_* calls to pass the proper length in the final
argument: use sizeof(<variable>) instead of sizeof(<type>),
since there were several inconsistencies between the actual
variable type and the size that was passed. This should
fix some problems on 64-bit architectures where sizeof(int)
!= sizeof(long).
|
|
2006-09-25 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_packet.c: (ospf_packet_dup, ospf_make_md5_digest)
Fix zlog_warn messages to eliminate compiler warnings.
(ospf_hello) Improve warning messages to show why we
are complaining.
|
|
Add Dragonfly.
Clarify that the C99 requirement includes libraries and headers, not
just compiler.
|
|
2006-09-19 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* bgpd.c: (peer_uptime) Fix printf format/arg mismatch in
zlog_warn message (%ld/size_t -> %lu/u_long).
|
|
2006-09-14 Paul Jakma <paul.jakma@sun.com>
* bgp_route.c: (bgp_process_queue_init) process queue hold time
too high, adds extra memory load. Change to be much lower,
until such time as it's made configurable.
|
|
2006-09-14 Paul Jakma <paul.jakma@sun.com>
* bgp_route.c: (bgp_table_stats_walker) Address space announced
should only count top-level unaggregateable prefixes, to
avoid falling afoul of anti-dodgy-accounting regulations
in various jurisdictions.. ;)
|
|
2006-09-14 Paul Jakma <paul.jakma@sun.com>
* (general) fix the peer refcount issue exposed by previous, by
just removing refcounting of peer threads, which is mostly
senseless as they're references leading from struct peer,
which peer_free cancels anyway. No need to muck around..
* bgp_fsm.h: Just remove the refcounting from the various
TIMER/READ/WRITE/EVENT ON/OFF/ADD macros.
* bgp_fsm.c: (bgp_stop) use BGP_EVENT_FLUSH, no refcounts attached
to events anymore.
(bgp_event) remove peer_unlock, events not refcounted.
* bgpd.c: (peer_free) flush events before free.
|
|
2006-09-14 Paul Jakma <paul.jakma@sun.com>
* (general) Fix some niggly issues around 'shutdown' and clearing
by adding a Clearing FSM wait-state and a hidden 'Deleted'
FSM state, to allow deleted peers to 'cool off' and hit 0
references. This introduces a slow memory leak of struct peer,
however that's more a testament to the fragility of the
reference counting than a bug in this patch, cleanup of
reference counting to fix this is to follow.
* bgpd.h: Add Clearing, Deleted states and Clearing_Completed
and event.
* bgp_debug.c: (bgp_status_msg[]) Add strings for Clearing and
Deleted.
* bgp_fsm.h: Don't allow timer/event threads to set anything
for Deleted peers.
* bgp_fsm.c: (bgp_timer_set) Add Clearing and Deleted. Deleted
needs to stop everything.
(bgp_stop) Remove explicit fsm_change_status call, the
general framework handles the transition.
(bgp_start) Log a warning if a start is attempted on a peer
that should stay down, trying to start a peer.
(struct .. FSM) Add Clearing_Completed
events, has little influence except when in state
Clearing to signal wait-state can end.
Add Clearing and Deleted states, former is a wait-state,
latter is a placeholder state to allow peers to disappear
quietly once refcounts settle.
(bgp_event) Try reduce verbosity of FSM state-change debug,
changes to same state are not interesting (Established->Established)
Allow NULL action functions in FSM.
* bgp_packet.c: (bgp_write) Use FSM events, rather than trying
to twiddle directly with FSM state behind the back of FSM.
(bgp_write_notify) ditto.
(bgp_read) Remove the vague ACCEPT_PEER peer_unlock, or else
this patch crashes, now it leaks instead.
* bgp_route.c: (bgp_clear_node_complete) Clearing_Completed
event, to end clearing.
(bgp_clear_route) See extensive comments.
* bgpd.c: (peer_free) should only be called while in Deleted,
peer refcounting controls when peer_free is called.
bgp_sync_delete should be here, not in peer_delete.
(peer_delete) Initiate delete.
Transition to Deleted state manually.
When removing peer from indices that provide visibility of it,
take great care to be idempotent wrt the reference counting
of struct peer through those indices.
Use bgp_timer_set, rather than replicating.
Call to bgp_sync_delete isn't appropriate here, sync can be
referenced while shutting down and finishing deletion.
(peer_group_bind) Take care to be idempotent wrt list references
indexing peers.
|
|
2006-09-13 Paul Jakma <paul.jakma@sun.com>
* bgp_aspath.c: (aspath_highest) new, return highest ASN in an
aspath.
* bgp_route.c: (bgp_peer_count_walker) new, do the walk done
in bgp_peer_counts as a thread.
(bgp_peer_counts) move walk to previous and call it via
thread_execute so this RIB walk shows up in thread stats.
(bgp_table_stats) New, gather some statistics for a given
RIB.
(bgp_table_stats_walker) New, RIB walker thread for former.
(bgp_table_stats_vty) Parsing front-end for 'show bgp ...',
useful model for future rationalisation of 'show ... bgp'.
(bgp_route_init) Add new RIB stats commands.
|
|
* kernel_socket.c (rtm_type_str): ifdef RTM_OLD{ADD,DEL} to
compile on systems that no longer define them.
|
|
2006-09-11 Paul Jakma <paul.jakma@sun.com>
* rip_routemap.c: (route_set_metric) underflow check needs to
use signed, problem identified and diagnosed by Pavel
Nikiforov in bug #293.
|
|
2006-09-11 Paul Jakma <paul.jakma@sun.com>
* ripd.c: (rip_read) remove gratuitous use of mid-function
declaration of vrecv, bug #278.
|
|
2006-09-06 Paul Jakma <paul.jakma@sun.com>
* (general) Squash any and all prefix-count issues by
abstracting route flag changes, and maintaining count as and
when flags are modified (rather than relying on explicit
modifications of count being sprinkled in just the right
places throughout the code).
* bgp_route.c: (bgp_pcount_{dec,inc}rement) removed.
(bgp_pcount_adjust) new, update prefix count as
needed for a given route.
(bgp_info_{uns,s}et_flag) set/unset a BGP_INFO route status
flag, calling previous function when appropriate.
(general) Update all set/unsets of flags to use previous.
Remove pcount_{dec,inc}rement calls.
No need to unset BGP_INFO_VALID in places where
bgp_info_delete is called, it does that anyway.
* bgp_{damp,nexthop}.c: Update to use bgp_info_{un,}set_flag.
* bgp_route.h: Export bgp_info_{un,}set_flag.
Add a 'meta' BGP_INFO flag, BGP_INFO_UNUSEABLE.
Move BGP_INFO_HOLDDOWN macro to here from bgpd.h
|
|
2006-09-03 Paul Jakma <paul.jakma@sun.com>
* bgp_route.c: Add 'show ... bgp ... <neighbour> prefix-count'
commands, to provide detailed counts of prefixes for a peer.
Informative, and should help pin down to pfxcnt drift
problems.
|
|
2006-08-28 Andy Gay <andy@andynet.net>
* ospf_packet.c: (ospf_make_db_desc) Assert added with More-bit
fixes does not hold up with addition of Ogier DB-Exchange
optimisation, which can empty the db-summary list in between
sent DD packets. Remove assert, update More-bit always when
in Exchange.
|
|
2006-08-27 Paul Jakma <paul.jakma@sun.com>
* configure.ac: Bump to 0.99.5
|
|
2006-08-27 J.J. Krabbendam <jkrabbendam@aimsys.nl>
* ospfd.c: (ospf_finish_final) default redistribute should be
unset too, fixes bug where reconfiguring ospfd completely
can no longer enable default redistribution.
|
|
2006-08-27 Paul Jakma <paul.jakma@sun.com>
* bgp_advertise.c: (bgp_sync_delete) fix mtype in XFREE.
NULL out peer->hash after free, to be sure.
|
|
2006-08-26 Paul Jakma <paul.jakma@sun.com>
* heavy-wq.c: (slow_func_del,slow_func) update to match workqueue
changes
|
|
2006-08-25 Paul Jakma <paul.jakma@sun.com>
* (general) Bug #134. Be more robust to backward time changes,
use the newly added libzebra time functions.
In most cases: recent_time -> recent_relative_time()
gettimeofday -> quagga_gettime (QUAGGA_CLK_MONOTONIC, ..)
time -> quagga_time.
(ospf_make_md5_digest) time() call deliberately not changed.
(ospf_external_lsa_refresh) remove useless gettimeofday, LSA
tv_orig time was already set in ospf_lsa_new, called via
ospf_external_lsa_new.
|
|
2006-08-25 Paul Jakma <paul.jakma@sun.com>
* thread.c: (general) Add support for monotonic clock, it may still
jump forward by huge amounts, but should be immune to going
backwards. Fixes bug #134.
(quagga_gettimeofday_relative_adjust) helper, does what name
says - adjusts gettimeofday based relative timer.
(quagga_gettimeofday) helper to keep recent_time up to date.
(quagga_get_relative) helper, update and getch the relative
timer using gettimeofday(). POSIX CLOCK_MONOTONIC is also
supported, but the code is not enabled yet nor tested.
(quagga_real_stabilised) helper, retrieve absolute time but
stabilised so as to never decrease.
(quagga_gettime) Exported interface, analogous to POSIX
clock_gettime() in interface, supporting several clocks.
(quagga_time) Exported interface, analogous to traditional
time(), will never decrease.
(recent_relative_time) Convenience function to retrieve
relative_time timeval, similar to existing recent_time absolute
timeval, for when an approximately recent value will do.
(remainder) Update to use above helpers.
(thread_getrusage) Previously was a macro, but needs to be
a function to twiddle with thread.c private stuff.
* thread.c: Point the GETRUSAGE macro at previous function.
Export quagga_gettime, quagga_time and recent_relative_time for
general use.
|
|
2006-08-03 Paul Jakma <paul.jakma@sun.com>
* ospf_packet.c: (ospf_make_db_desc) Implement
draft-ogier-ospf-dbex-opt DB-exchange optimisation.
|
|
2006-08-03 Paul Jakma <paul.jakma@sun.com>
* ospf_packet.c: (ospf_make_db_desc) Unset the DD More bit
after constructing the packet, if appropriate.
(ospf_db_desc_proc) Speed up Exchange, slave should raise
ExchangeDone earlier, as RFC mandates, by forming its reply
before deciding whether both sides are done, avoids a
needless round of empty DD packet exchanges at the end of
Exchange, hence speeding up ExchangeDone.
(ospf_db_desc) use UNSET_FLAG macro.
|
|
2006-08-04 Paul Jakma <paul.jakma@sun.com>
* ospf_lsdb.c: (ospf_lsdb_delete_entry) new function, consolidate
exact same functionality replicated in other functions.
(ospf_lsdb_add) Strip out code by using ospf_lsdb_delete_entry.
(ospf_lsdb_delete) ditto.
(ospf_lsdb_delete_all) ditto.
|
|
2006-08-06 Paul Jakma <paul.jakma@sun.com>
* rtadv.h: depends on interface.h, so should include it.
|
|
2006-08-06 Paul Jakma <paul.jakma@sun.com>
* interface.h: (ifstat_update_proc) declaration should match
ifstat_update_sysctl really, which is to not return status, as
such status is not used anywhere.
* if_{proc,sysctl}.c: Make ifstat_update_* definitions and return values
consistent with each other and their declarations, ie:
(void) (*) (void).
|
|
2006-08-06 Paul Jakma <paul.jakma@sun.com>
* bgp_aspath.c: (aspath_loop_check) Fix the typo-bug which
essentially had disabled this check. Problem reported by
Bartek Kania <mrbk@gnarf.org> in [quagga-users 7388].
* aspath_test.c: (validate) Fix the sense of the aspath_loop_check,
which was the wrong way around and had actually been testing for
aspath_loop_check to be buggy.
|
|
2006-08-01 Paul Jakma <paul.jakma@sun.com>
* irdp_main.c: (irdp_advertisement) free the stream here, when done,
right under where it was allocated so it's blindingly obvious
it's correct. This possibly fixes a very slow leak of streams in
zebra.
* irdp_packet.c: (send_packet) don't free the stream here as
it's hard to tell if right, plus an error case seemed to
returning before free anyway.
|
|
2006-08-04 Paul Jakma <paul.jakma@sun.com>
* misc_null.c: Add ifstat_update_sysctl, add another required
header.
|
|
2006-08-02 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* misc_null.c: Must include header files to get older versions of gcc
to process the #pragma statements properly.
|
|
2006-07-28 Paul Jakma <paul.jakma@sun.com>
* main.texi: link-detect works on Solaris too.
* ospfd.texi: Twiddle around with anchors a bit more.
Clarify how setting MD5 auth by area and by interface interact,
and add cross-references, as well as to the required
command for setting key material.
|
