| Age | Commit message (Collapse) | Author |
|---|
|
IP source address in the OSPF packets. It was sometimes problematic
in actual operation (needed some operational cost: restarting
all-neighbor routers when I/F NIC was changed). Due to this change,
a previously safe case, attaching multiple interface to the same
link will now be dengerous and will not work. Remedy to that should
be applied later.
[port from GNU Zebra]
|
|
inactivity_timer() deletes the neighbor from the neighbor_list, it
cannot be called by thread_execute() from inner side of the
neighbor_list for-loop.
(Although crash was already fixed in Quagga, it's better follow the
GNU Zebra logic).
[port from GNU Zebra]
|
|
database ..." commands for vtysh by extract.pl. Remove duplicate
install_element calls.
Fixes bugzilla #194. [backport candidate]
|
|
Implement non-blocking zclient I/O with buffering.
* zclient.h (struct zclient): Add two fields to support non-blocking
I/O: struct buffer *wb, and struct thread *t_write.
(zclient_free): Remove function.
(zebra_redistribute_send): Change 2nd arg from socket fd to
struct zclient * (needed to support non-blocking I/O and buffering).
(zclient_send_message): New function to send an arbitrary
message with non-blocking I/O.
* zclient.c (zclient_new): Create write buffer.
(zclient_free): Remove unused function.
(zclient_stop): Must cancel new t_write thread. Also, reset
all buffers: ibuf, obuf, and wb.
(zclient_failed): New helper function for typical error handling.
(zclient_flush_data): New thread to flush queued data.
(zclient_send_message): New function to send the message in
zclient->obuf to zebra using non-blocking I/O and buffering.
(zebra_message_send, zapi_ipv4_route, zapi_ipv6_route): Use
new zclient_send_message function instead of calling writen.
(zclient_start): Set socket non-blocking. Also, change 2nd arg
to zebra_redistribute_send from zclient->sock to zclient.
(zebra_redistribute_send): Change 2nd arg to struct zclient *.
Can now use zclient->obuf to assemble the message instead of
allocating a temporary stream. And call zclient_send_message to
send the message instead of writen.
(zclient_read): Convert to support non-blocking I/O by using
stream_read_try instead of deprecated stream_read.
(zclient_redistribute): Change 2nd arg to zebra_redistribute_send
from zclient->sock to zclient.
* ospf6_zebra.c (ospf6_zebra_redistribute, ospf6_zebra_no_redistribute):
Change 2nd arg to zebra_redistribute_send from zclient->sock
to zclient.
* ospf_zebra.c (ospf_zebra_add): Call zclient_send_message instead
of writen.
* rip_zebra.c (rip_redistribute_set, rip_redistribute_unset,
rip_redistribute_clean): Change 2nd arg to zebra_redistribute_send
from zclient->sock to zclient.
* ripng_zebra.c (ripng_redistribute_unset, ripng_redistribute_clean):
Change 2nd arg to zebra_redistribute_send from zclient->sock
to zclient.
* bgp_zebra.c (bgp_redistribute_set, bgp_redistribute_unset):
The 2nd arg to zebra_redistribute_send is now zclient instead of
zclient->sock.
* isis_zebra.h (isis_zebra_finish): Remove declaration of unused
function.
* isis_zebra.c (isis_zebra_route_add_ipv4): Call zclient_send_message
to send the message to zebra instead of calling writen directly, since
zclient_send_message understands non-blocking I/O and will manage
the buffer queue appropriately.
(isis_zebra_finish): Remove unused function, particularly since
the zclient_free function has been removed.
|
|
* (global): Fix up list loops to match changes in lib/linklist,
and some basic auditing of usage.
* configure.ac: define QUAGGA_NO_DEPRECATED_INTERFACES
* HACKING: Add notes about deprecating interfaces and commands.
* lib/linklist.h: Add usage comments.
Rename getdata macro to listgetdata.
Rename nextnode to listnextnode and fix its odd behaviour to be
less dangerous.
Make listgetdata macro assert node is not null, NULL list entries
should be bug condition.
ALL_LIST_ELEMENTS, new macro, forward-referencing macro for use
with for loop, Suggested by Jim Carlson of Sun.
Add ALL_LIST_ELEMENTS_RO for cases which obviously do not need the
"safety" of previous macro.
LISTNODE_ADD and DELETE macros renamed to ATTACH, DETACH, to
distinguish from the similarly named functions, and reflect their
effect better.
Add a QUAGGA_NO_DEPRECATED_INTERFACES define guarded section
with the old defines which were modified above,
for backwards compatibility - guarded to prevent Quagga using it..
* lib/linklist.c: fix up for linklist.h changes.
* ospf6d/ospf6_abr.c: (ospf6_abr_examin_brouter) change to a single
scan of the area list, rather than scanning all areas first for
INTER_ROUTER and then again for INTER_NETWORK. According to
16.2, the scan should be area specific anyway, and further
ospf6d does not seem to implement 16.3 anyway.
|
|
* ospf_interface.h: (ospf_if_lookup_by_name) Remove declaration of a
function that does not exist.
* ospf6_interface.[ch]: (ospf6_interface_lookup_by_name) Remove unused
function.
|
|
Fix problems when netlink interfaces are renamed (same ifindex used
for a new interface). Start cleaning up some problems with the way
interface names are handled.
* interface.c: (if_new_intern_ifindex) Remove obsolete function.
(if_delete_update) After distributing the interface deletion message,
set ifp->ifindex to IFINDEX_INTERNAL.
(if_dump_vty) Detect pseudo interface by checking if ifp->ifindex is
IFINDEX_INTERNAL.
(zebra_interface) Check return code from interface_cmd.func.
Do not set internal ifindex values to if_new_intern_ifindex(),
since we now use IFINDEX_INTERNAL for all pseudo interfaces.
* kernel_socket.c: (ifm_read) Fix code and comments to reflect that
all internal interfaces now have ifp->ifindex set to IFINDEX_INTERNAL.
* rt_netlink.c: (set_ifindex) New function used to update ifp->ifindex.
Detects interface rename events by checking if that ifindex is already
being used. If it is, delete the old interface before assigning
the ifindex to the new interface.
(netlink_interface, netlink_link_change) Call set_ifindex to update
the ifindex.
* if.h: Remove define for IFINDEX_INTERNBASE and add define
IFINDEX_INTERNAL 0, since all internal (i.e. non-kernel) pseudo-
interfaces should have ifindex set to 0.
(if_new) Remove function.
(if_delete_retain) New function to delete an interface without
removing from iflist and freeing the structure.
(ifname2ifindex) New function.
* if.c: (if_new) Remove function (absorb into if_create).
(if_create) Replace function if_new with call to calloc.
Set ifp->ifindex to IFINDEX_INTERNAL. Fix off-by-one error
in assert to check length of interface name. Add error message
if interface with this name already exists.
(if_delete_retain) New function to delete an interface without
removing from iflist and freeing the structure.
(if_delete) Implement with help of if_delete_retain.
(ifindex2ifname) Reimplement using if_lookup_by_index.
(ifname2ifindex) New function to complement ifindex2ifname.
(interface) The interface command should check the name length
and fail with a warning message if it is too long.
(no_interface) Fix spelling in warning message.
(if_nametoindex) Reimplement using if_lookup_by_name.
(if_indextoname, ifaddr_ipv4_lookup) Reimplement using
if_lookup_by_index.
* bgp_zebra.c: (bgp_interface_delete) After deleting, set ifp->ifindex
to IFINDEX_INTERNAL.
* isis_zebra.c: (isis_zebra_if_del) Call if_delete_retain instead
of if_delete, since it is generally not safe to remove interface
structures. After deleting, set ifp->ifindex to IFINDEX_INTERNAL.
(zebra_interface_if_lookup) Tighten up code.
* ospf6_zebra.c: (ospf6_zebra_if_del) Previously, this whole function
was commented out. But this is not safe: we should at least update
the ifindex when the interface is deleted. So the new version
updates the interface status and sets ifp->ifindex to
IFINDEX_INTERNAL.
(ospf6_zebra_route_update) Use if_indextoname properly.
* ospf_vty.c: (show_ip_ospf_interface_sub) Show ifindex and interface
flags to help with debugging.
* ospf_zebra.c: (ospf_interface_delete) After deleting, set ifp->ifindex
to IFINDEX_INTERNAL.
(zebra_interface_if_lookup) Make function static. Tighten up code.
* rip_interface.c: (rip_interface_delete) After deleting, set
ifp->ifindex to IFINDEX_INTERNAL.
* ripng_interface.c: (ripng_interface_delete) After deleting, set
ifp->ifindex to IFINDEX_INTERNAL.
|
|
* ospf6_route.c: (ospf6_route_show, ospf6_route_show_detail) Protect
against the possibility that the string returned by if_indextoname
may not terminate with '\0'.
|
|
Thanks to Mohit Thakur.
|
|
* ospf6_asbr.c: Add "hsls" to the zroute_name const char array.
|
|
|
|
* bgp_main.c: (main) The 2nd argument to openzlog has been removed.
* isis_main.c: (main) The 2nd argument to openzlog has been removed.
* ospf6_main.c: (main) The 2nd argument to openzlog has been removed.
Note that stdout logging will no longer be enabled by default when
not running as a daemon.
* ospf_main.c: (main) The 2nd argument to openzlog has been removed.
* rip_main.c: (main) The 2nd argument to openzlog has been removed.
* ripng_main.c: (main) The 2nd argument to openzlog has been removed.
* main.c: (main) The 2nd argument to openzlog has been removed.
So stdout logging will no longer be enabled by default.
* irdp_main.c: (irdp_finish) Reduce severity of shutdown message
from LOG_WARNING to LOG_INFO.
* vtysh.c: Make several functions static instead of global.
Added several commands to support destination-specific logging levels.
(vtysh_completion) This function is unused, so comment it out.
* basic.texi: Document new logging features. Separate basic config
commands from basic VTY commands.
* log.h: Replace struct zlog flags and maskpri fields with maxlvl
array to support individual logging levels for each destination.
Remove the 2nd argument to openzlog since the default logging config
should be standardized inside the library. Replaced the
zlog_set_flag and zlog_reset_flag functions with zlog_set_level.
And zlog_set_file now requires an additional log_level argument.
Declare zlog_proto_names for use inside command.c in the
"show logging" command. Added defines useful for command
construction.
* log.c: (vzlog) Decide where to send the message based on the
individual logging levels configured for each destination.
Remove support for ZLOG_STDERR since it was never actually used.
Support record-priority for terminal monitors.
(zlog_signal,zlog_backtrace_sigsafe) Support destination-specific
logging levels. Remove stderr support (was never used). Added
support for terminal monitor logging.
(_zlog_assert_failed) Increase message severity to LOG_EMERG.
(openzlog) Remove 2nd argument since default config should be
standardized in library. By default, terminal monitoring
is set to debug, and all other logging is disabled.
(zlog_set_flag,zlog_reset_flag) Removed.
(zlog_set_level) New function to replace zlog_set_flag and
zlog_reset_flag. Supports destination-specific logging levels.
(zlog_set_file,zlog_reset_file) Support file-specific logging level.
(zlog_rotate) Log an error message if fopen fails, and support
new file-specific logging level.
* command.h: Change DEFUN_CMD_FUNC_DECL and DEFUN_CMD_FUNC_TEXT so that
command functions will be static instead of global. Remove
declarations for config_exit and config_help. Define new macros
DEFUNSH_ATTR, DEFUNSH_HIDDEN, and DEFUNSH_DEPRECATED so we can
have deprecated commands in vtysh. Similarly, for completeness,
define macros ALIAS_SH, ALIAS_SH_HIDDEN, and ALIAS_SH_DEPRECATED.
Also, fix bug in ALIAS_ATTR macro (didn't matter because it
was never used).
* command.c: Make many functions static instead of global.
(facility_name,facility_match,level_match) New functions
to support enhanced destination-specific logging levels.
(config_write_host) Support new destination-specific logging levels.
(config_logmsg) Added new "logmsg" command to help test logging
system.
(show_logging) Added "show logging" command to show the current
configuration of the logging system.
(config_log_stdout_level) Support explicit stdout logging level.
(no_config_log_stdout) Now takes optional LEVEL arg.
(config_log_monitor,config_log_monitor_level,no_config_log_monitor)
New commands creating new "log monitor" commands to set terminal
monitoring log level.
(config_log_file_level) Support explicit file logging level.
(config_log_syslog_level) Support explicit syslog logging level.
(config_log_facility,no_config_log_facility) Implement new
"log facility" command.
(cmd_init) Add hooks for new commands: "show logging", "logmsg",
"log stdout <level>", "log monitor", "log monitor <level>",
"no log monitor", "log file <filename> <level>",
"no log file <filename> <level>", "log syslog <level>",
"log facility", and "no log facility".
* vty.h: Added a "level" argument to vty_log so it can support
"log record-priority". Declare new function vty_log_fixed for
use in signal handlers.
* vty.c: (vty_log,vty_log_out) Added a "level" argument to support
"log record-priority" for vty terminal monitors.
(vty_down_level) Use config_exit_cmd.func instead of calling
config_exit directly (since command functions will now be static
instead of global).
(vty_log_fixed) New function to send terminal monitor messages
from inside a signal handler.
|
|
* bgp_main.c: (sigint) Use zlog_notice for termination message.
(main) Use zlog_notice for startup announcement.
* isis_main.c: (sigint,sigterm) Use zlog_notice for termination message.
(terminate) This function should be static, not global.
(main) Use zlog_notice for startup announcement, and remove
ifdef ZEBRA_VERSION.
* version.h.in: Remove declaration for pid_output_lock, this function
is now static, not global.
* pid_output.c: (pid_output_lock) This function should be static, not
global. And remove "old umask" error message, since it was really
an unimportant debug message, not an error.
(pid_output) Need to declare static function pid_output_lock.
* ospf6_main.c: (sigint,sigterm) Use zlog_notice for termination
message.
(main) Remove commented-out call to pid_output_lock (which should
never be called other than from inside pid_output). And use
zlog_notice to print the startup message, which now includes
the vty port.
* ospf_main.c: (sigint) Use zlog_notice for termination message.
(main) Issue a startup announcement using zlog_notice.
* rip_main.c: (sigint) Use zlog_notice for termination message.
(main) Add a startup announcement using zlog_notice.
* ripng_main.c: (sighup) Remove spurious terminating message.
(sigint) Use zlog_notice for termination message.
(main) Issue a startup announcement using zlog_notice.
* main.c: (sigint) Use zlog_notice for termination message.
(main) Add a startup announcement using zlog_notice.
|
|
|
|
|
|
|
|
* ospf6_flood.c: When adding a thread to retransmit an lsa after
rxmt_interval, the ospf6d used thread_add_event(). However,
thread_add_event() executes immediately and ignores the delay parameter.
This was causing unnecesary unicast LSU sends. Adding the thread has
been changed to use thread_add_timer() which will expire after delay.
After the fix results appear consistent with expectation.
|
|
initializes connection, and "no smux peer" command terminates it. Fixes
bugzilla #47 and #112.
|
|
|
|
* ospf6_route.c: Add const qualifier to various char arrays of
constants. signed/unsigned fixes.
(ospf6_linkstate_table_show) argv is const
* ospf6_snmp.c: listnode typedef is dead.
(ospf6_snmp_init) Take struct thread_master arg, needed for
smux_init.
* ospf6_snmp.h: update ospf6_snmp_init declaration.
* ospf6d.c: (ospf6_init) add const qualifier to sargv, pass master
to ospf_snmp6_init.
* ospf6_asbr.c: const char update.
* ospf6_interface.c: ditto, plus signed/unsigned fixes.
(ipv6_ospf6_cost) Check whether cost fits in u_int32_t and use
strtoul.
* ospf6_intra.c: const char update. Parenthesise expression.
* ospf6_lsa.c: signed/unsigned and const char updates.
* ospf6_proto.c: ditto.
* ospf6_message.c: ditto.
* ospf6_lsdb.c: signed/unsigned update.
* ospf6_main.c: const char update.
* ospf6_neighbor.c: ditto.
* ospf6_spf.c: ditto.
* ospf6_top.c: ditto.
|
|
* Makefile.am: fix listing of ospf_snmp.c in noinst_HEADERS
|
|
|
|
|
|
to ospf6_network.h.
|
|
|
|
|
|
|
|
|
|
|
|
conflict the ones in lib/sigevent.c. Fixes compiling with --disable-shared.
|
|
|
|
|
|
ospf6_lsdb prototype declaration from ospf6_lsa.h. Report sent to Yasuhiro
Ohara as well.
|
|
|
|
|
|
|
|
* ospf6_main.c: Delete LOG_PERROR, not portable.
* ospf6_network.c: (ospf6_set_pktinfo) use setsockopt_ipv6_pktinfo
|
|
|
|
fixes.
|
|
zclient changes.
|
|
* bgp_zebra.c: (bgp_interface_address_add) sync to zclient changes
(bgp_interface_address_delete) ditto.
(bgp_zebra_announce) ditto.
(bgp_zebra_withdraw) ditto.
* isis_zebra.c: Sync with zclient changes.
* zclient.c (zapi_ipv4_route) Follow Sowmini's lead and describe
message format.
* ospf6_zebra.c: Sync to zclient changes
* ospf_zebra.c: Sync with lib/zclient changes
* rip_zebra.c: sync with zclient changes.
* rip_interface.c: ditto.
* ripng_{interface,zebra}.c: sync with zclient changes
2004-05-08 Sowmini Varadhan <sowmini.varadhan@sun.com>
* zclient.c: (zapi_ipv4_add) collapsed into zapi_ipv4_route
(zapi_ipv4_delete) ditto.
(zapi_ipv4_route) add/delete a route by way of cmd arg.
(zapi_ipv6_add) collapsed into zapi_ipv6_route.
(zapi_ipv6_delete) ditto.
(zapi_ipv6_route) add/delete a route by way of cmd arg.
(zebra_interface_address_delete_read) collapsed into
zebra_interface_address_read.
(zebra_interface_address_delete_read) ditto.
(zebra_interface_address_read) read address add/delete messages
by way of type argument. Describe command message format.
(zebra_interface_add_read) Unconditionally read new ifmtu6 field.
Describe command message format.
(zebra_interface_state_read) Unconditionally read new ifmtu6 field.
(zclient_redistribute_set) Collapsed into zclient_redistribute
(zclient_redistribute_unset) ditto
(zclient_redistribute) set/unset redistribution.
(zclient_redistribute_default_set) Collapsed into
zclient_redistribute_default.
(zclient_redistribute_default_unset) ditto.
(zclient_redistribute_default) Redistribute default set/unset.
* zclient.h: delete zapi_ipv{4,6}_add, zapi_ipv{4,6}_delete. Add
zapi_ipv{4,6}_route. delete zclient_redistribute_set/unset. Add
zclient_redistribute. Ditto for
zclient_redistribute_default_{set/unset}.
|
|
* ospf6_ism.c: DR Election bug fix.
|
|
Subject: [zebra 19093] [PATCH] Two more fixes
1) From 6Wind patch - show router and interface nodes from ospf6d when
using vtysh and don't show defaults in interface node. Fixes bugzilla
#14.
|
|
|
|
|
