| Age | Commit message (Collapse) | Author |
|---|
|
Compiled on 32-bit and 64-bit linux gcc 4.1.2 platforms.
No run-time testing on 32-bit and limited run-time testing on 64-bit.
|
|
--without-crypto
Autoconfig work by me, the rest was done by
"Kirill K. Smirnov" <lich@math.spbu.ru>
|
|
2007-03-14 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_snmp.c: (ospf_snmp_neighbor_state) New function to
map internal quagga neighbor states to SNMP standard values.
(ospfNbrEntry) Call new ospf_snmp_neighbor_state function.
|
|
2006-12-12 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* if.h: (struct connected) Add new ZEBRA_IFA_PEER flag indicating
whether a peer address has been configured. Comment now shows
the new interpretation of the destination addr: if ZEBRA_IFA_PEER
is set, then it must contain the destination address, otherwise
it may contain the broadcast address or be NULL.
(CONNECTED_DEST_HOST,CONNECTED_POINTOPOINT_HOST) Remove obsolete
macros that were specific to IPv4 and not fully general.
(CONNECTED_PEER) New macro to check ZEBRA_IFA_PEER flag.
(CONNECTED_PREFIX) New macro giving the prefix to insert into
the RIB: if CONNECTED_PEER, then use the destination (peer) address,
else use the address field.
(CONNECTED_ID) New macro to come up with an identifying address
for the struct connected.
* if.c: (if_lookup_address, connected_lookup_address) Streamline
logic with new CONNECTED_PREFIX macro.
* prefix.h: (PREFIX_COPY_IPV4, PREFIX_COPY_IPV6) New macros
for better performance than the general prefix_copy function.
* zclient.c: (zebra_interface_address_read) For non-null destination
addresses, set prefixlen to equal the address prefixlen. This
is needed to get the new CONNECTED_PREFIX macro to work properly.
* connected.c: (connected_up_ipv4, connected_down_ipv4,
connected_up_ipv6, connected_down_ipv6) Simplify logic using the
new CONNECTED_PREFIX macro.
(connected_add_ipv4) Set prefixlen in destination addresses (required
by the CONNECTED_PREFIX macro). Use CONNECTED_PEER macro instead
of testing for IFF_POINTOPOINT. Delete invalid warning message.
Warn about cases where the ZEBRA_IFA_PEER is set but no
destination address has been supplied (and turn off the flag).
(connected_add_ipv6) Add new flags argument so callers may set
the ZEBRA_IFA_PEER flag. If peer/broadcast address satisfies
IN6_IS_ADDR_UNSPECIFIED, then reject it with a warning.
Set prefixlen in destination address so CONNECTED_PREFIX will work.
* connected.h: (connected_add_ipv6) Add new flags argument so
callers may set the ZEBRA_IFA_PEER flag.
* interface.c: (connected_dump_vty) Use CONNECTED_PEER macro
to decide whether the destination address is a peer or broadcast
address (instead of checking IFF_BROADCAST and IFF_POINTOPOINT).
* if_ioctl.c: (if_getaddrs) Instead of setting a peer address
only when the IFF_POINTOPOINT is set, we now accept a peer
address whenever it is available and not the same as the local
address. Otherwise (no peer address assigned), we check
for a broadcast address (regardless of the IFF_BROADCAST flag).
And must now pass a flags value of ZEBRA_IFA_PEER to
connected_add_ipv4 when a peer address is assigned.
The same new logic is used with the IPv6 code as well (and we
pass the new flags argument to connected_add_ipv6).
(if_get_addr) Do not bother to check IFF_POINTOPOINT: just
issue the SIOCGIFDSTADDR ioctl and see if we get back
a peer address not matching the local address (and set
the ZEBRA_IFA_PEER in that case). If there's no peer address,
try to grab SIOCGIFBRDADDR regardless of whether IFF_BROADCAST is set.
* if_ioctl_solaris.c: (if_get_addr) Just try the SIOCGLIFDSTADDR ioctl
without bothering to check the IFF_POINTOPOINT flag. And if
no peer address was found, just try the SIOCGLIFBRDADDR ioctl
without checking the IFF_BROADCAST flag. Call connected_add_ipv4
and connected_add_ipv6 with appropriate flags.
* if_proc.c: (ifaddr_proc_ipv6) Must pass new flags argument to
connected_add_ipv6.
* kernel_socket.c: (ifam_read) Must pass new flags argument to
connected_add_ipv6.
* rt_netlink.c: (netlink_interface_addr) Copy logic from iproute2
to determine local and possible peer address (so there's no longer
a test for IFF_POINTOPOINT). Set ZEBRA_IFA_PEER flag appropriately.
Pass new flags argument to connected_add_ipv6.
(netlink_address) Test !CONNECTED_PEER instead of if_is_broadcast
to determine whether the connected destination address is a
broadcast address.
* bgp_nexthop.c: (bgp_connected_add, bgp_connected_delete)
Simplify logic by using new CONNECTED_PREFIX macro.
* ospf_interface.c: (ospf_if_is_configured, ospf_if_lookup_by_prefix,
ospf_if_lookup_recv_if) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_lsa.c: (lsa_link_ptop_set) Using the new CONNECTED_PREFIX
macro, both options collapse into the same code.
* ospf_snmp.c: (ospf_snmp_if_update) Simplify logic using new
CONNECTED_ID macro.
(ospf_snmp_is_if_have_addr) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_vty.c: (show_ip_ospf_interface_sub) Use new CONNECTED_PEER macro
instead of testing the IFF_POINTOPOINT flag.
* ospfd.c: (ospf_network_match_iface) Use new CONNECTED_PEER macro
instead of testing with if_is_pointopoint. And add commented-out
code to implement alternative (in my opinion) more elegant behavior
that has no special-case treatment for PtP addresses.
(ospf_network_run) Use new CONNECTED_ID macro to simplify logic.
* rip_interface.c: (rip_interface_multicast_set) Use new CONNECTED_ID
macro to simplify logic.
(rip_request_interface_send) Fix minor bug: ipv4_broadcast_addr does
not give a useful result if prefixlen is 32 (we require a peer
address in such cases).
* ripd.c: (rip_update_interface) Fix same bug as above.
|
|
2006-06-24 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_snmp.c: (ospfTrapNbrStateChange, ospfTrapIfStateChange) Improve
info log message to indicate why the trap is being sent.
|
|
* ospf_snmp.c: Avoid mixing interface and ospf_interface objects
which now allows snmpwalk to work with ospfIfTable and
also with ospfIfMetricTable
|
|
* lib/smux.[ch]: allow to retreive global OID (identified by <0
namelen).
* ospf_ism.c: generate SNMP traps on Interface state change
* ospf_nsm.c: generate SNMP traps on Neighbour state change
* ospf_snmp.[ch]: support for SNMP traps for interface and neighbours.
|
|
* Of course ISM_SNMP MACRO mist be defined
|
|
* ospfd/ospf_vty.c: forece default route LSA to be re_issued whenever
cost is changed ( [no] ip ospf area XXX default-cost YYY)
Support ignore-mtu option
* ospfd/ospfd.h: define OSPF_MTU_IGNORE_DEFAULT
* ospfd/ospf_packet.c: support ignore-mtu option
* ospfd/ospf_interface.h: field added for skipping MTU check
* ospfd/ospf_interface.c: fix memory leak in ospf_crypt_key_delete()
Set mtu_ignore field to default value
* ospfd/ospf_abr.[ch]: export ospf_abr_announce_network_to_area()
* ospfd/ospf_ism.h: add MACRO to convert internal ISM status into SNMP
correct values
* ospfd/ospf_snmp.c: add sanity check on LSA type in lsdb_lookup_next()
convert OSPFIFSTATE internal status into SNMP values
|
|
* (global): Fix up list loops to match changes in lib/linklist,
and some basic auditing of usage.
* configure.ac: define QUAGGA_NO_DEPRECATED_INTERFACES
* HACKING: Add notes about deprecating interfaces and commands.
* lib/linklist.h: Add usage comments.
Rename getdata macro to listgetdata.
Rename nextnode to listnextnode and fix its odd behaviour to be
less dangerous.
Make listgetdata macro assert node is not null, NULL list entries
should be bug condition.
ALL_LIST_ELEMENTS, new macro, forward-referencing macro for use
with for loop, Suggested by Jim Carlson of Sun.
Add ALL_LIST_ELEMENTS_RO for cases which obviously do not need the
"safety" of previous macro.
LISTNODE_ADD and DELETE macros renamed to ATTACH, DETACH, to
distinguish from the similarly named functions, and reflect their
effect better.
Add a QUAGGA_NO_DEPRECATED_INTERFACES define guarded section
with the old defines which were modified above,
for backwards compatibility - guarded to prevent Quagga using it..
* lib/linklist.c: fix up for linklist.h changes.
* ospf6d/ospf6_abr.c: (ospf6_abr_examin_brouter) change to a single
scan of the area list, rather than scanning all areas first for
INTER_ROUTER and then again for INTER_NETWORK. According to
16.2, the scan should be area specific anyway, and further
ospf6d does not seem to implement 16.3 anyway.
|
|
exist at all.
[backport candidate]
|
|
ripd might need some more testing though.
|
|
initializes connection, and "no smux peer" command terminates it. Fixes
bugzilla #47 and #112.
|
|
* (global) Const char update and signed/unsigned fixes.
* (various headers) size defines should be unsigned.
* ospf_interface.h: remove duplicated defines, include the
authoritative header - though, these defines should probably
be moved to a dedicated header, or ospfd.h.
* ospf_lsa.h: (struct lsa) ls_seqnum should be unsigned.
* ospf_packet.c: (ospf_write) cast result of shift to unsigned.
|
|
* ospf_snmp.c: Missed list typedef update
* ospf_dump.c: Include sockopt.h for header swab functions.
|
|
* zebra/connected.c: revert the 'generic PtP' patch as it causes
far too many problems. People who use FreeSWAN should investigate
native linux ipsec.
* zebra/rt_netlink.c: ditto
* lib/if.c: ditto
* ripd/ripd.h: ditto
* ripd/ripd.c: ditto
* ripd/rip_interface.c: ditto
* ospfd/ospfd.c: ditto
* ospfd/ospf_snmp.c: ditto
* bgpd/bgp_nexthop.c: ditto
|
|
* Fix lib/smux.c's reliance on daemons exporting struct
thread_master *master.
|
|
* Sync to Zebra CVS
* Fix lib/thread.h leak
* Fix small Opaque LSA leak
* Do not configure OSPF interfaces for secondary addresses
* vtysh fixes from Hasso
* Dave Watson's missing ntohs fix
|
|
* sync to latest zebra CVS
* spec file: updated and added define for ospf-api/client
NB: OSPF-API has been broken by the zebra.org changes, which
has added struct ospf * as a new arg to many functions
|
|
|
|
|
|
|
