| Age | Commit message (Collapse) | Author |
|---|
|
When a range (or sub-range) is deleted, the area is notified by propagating a
MAXAGE LSA. This LSA stays in the database for a while to both insure
propagation as well as in the off chance that it's useful in the near future.
Unfortunately, the ABR algorithm was treating these MAXAGE LSAs as unchanged and
not propagating them within the areas.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
ISSUE
When an area range is created in which there the sub-area has routes that are
smaller than the range, an ABR creates a blackhole route to cover the range.
When the range is removed, the blackhole route is not removed.
--A----B----C---
B is an ABR with A in area 1 and C in area 0. If A advertises `10.2.0.0/30` and
`10.2.0.4/30` and B is configured with `area 0.0.0.1 range 10.2.0.0/29` a
blackhole is created on B (`blackhole 10.2.0.0/29 proto zebra`). When the
area/range is removed via the command line, the blackhole remains in existence
even though the "range" route is removed from area 0 and the individual routes
are propagated.
PATCH
The reason for this behavior is that, prior to this patch, the range is deleted
from the area's list, so when ospf_abr_manage_discard_routes() gets called,
there is nothing to clean up. The patch removes the discard route as part of
the processing of the command line (ospf_area_range_unset()).
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
OVERVIEW
The checksum used in OSPF (rfc2328) is specified in rc905 annex B. There is an
sample implementation in rfc1008 which forms the basis of the quagga
implementation. This algorithm works perfectly when generating a checksum;
however, validation is a bit problematic.
The following LSA (generated by a non-quagga implementation) is received by
quagga and marked with an invalid checksum; however, it passes both the rfc905
and rfc1008 validation checks.
static uint8_t lsa_10_121_233_29[] = {
0x0e, 0x10, 0x02, 0x03,
0x09, 0x00, 0x35, 0x40,
0x0a, 0x79, 0xe9, 0x1d,
0x80, 0x00, 0x00, 0x03,
0x00, 0x8a, 0x00, 0x1c,
0xff, 0xff, 0xff, 0xe0,
0x00, 0x00, 0x36, 0xb0
};
LS Type: Summary-LSA (IP network)
LS Age: 3600 seconds
Do Not Age: False
Options: 0x02 (E)
Link-State Advertisement Type: Summary-LSA (IP network) (3)
Link State ID: 9.0.53.64
Advertising Router: 10.121.233.29 (10.121.233.29)
LS Sequence Number: 0x80000003
LS Checksum: 0x008a
Length: 28
Netmask: 255.255.255.224
Metric: 14000
You'll note that one byte of the checksum is 0x00; quagga would calculate the
checksum as 0xff8a.
It can be argued that the sourcing implementation generates an incorrect
checksum; however, rfc905 indicates that, for 1's complement arithmetic, the
value 255 shall be regarded as 0, thus either values are valid.
EXPLANATION
The quagga ospfd and ospf6d implementations operate by copying the PDU's
existing checksum in a holding variable, calculating the checksum, and comparing
the resulting checksum to the original. As a note, this implementation has the
side effect of modifying the contents of the PDU.
Evaluation of both rfc905 and rfc1008 shows that checksum validation should
involve calculating the sum over the PDU and checking that both resulting C0 and
C1 values are zero. This behavior is enacted in the rfc1008 implementation by
calling encodecc with k = 0 (checksum offset); however, this functionality had
been omitted from the quagga implementation.
PATCH
This patch adds the ability to call the quagga's fletcher_checksum() with a
checksum offset value of 0xffff (aka FLETCHER_CHECKSUM_VALIDATE) which returns
the sum over the buffer (a value of 0 indicates a valid checksum). This is
similar to the mechanism in rfc1008 when called with k = 0. The patch also
introduces ospf_lsa_checksum_valid().
ospf6d had it's own implementation of the fletcher checksum in
ospf6_lsa_checksum(); it's the same algorithm as in fletcher_checksum(). This
patch removes the local implementation in favor of the library's as well as creates
and uses ospf6_lsa_checksum_valid().
quagga's ISIS implementation suffers from the same problem; however, I do not
have the facilities to validate a fix to ISIS, thus this change has been left to
the ISIS maintainers. The function iso_csum_verify() should be reduced to
running the fletcher checksum over the buffer using an offset of 0.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Nolan Leake <nolan@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
This reverts commit 9289c6ff55cd96c943d23e43fc9e5f987aa965ed.
The commit reverted an earlier change which was fixed a bug that caused
black-holes to remote destinations with multiple paths, that could occur
during convergence. Overall, the previous code is more correct.
|
|
This corrects the parameters passed to libtool when linking
the shared libraries. The paramter name is -version-info not
-version.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
The patch in bug 330 did two things. It add a return value
whether ospf_nexthop_calculation() failed or not and also
moved the return stmt for 16.1.1 para 5 so now SPF
will fallback to the intervening router when no back links are found
by 16.1.1 para 5. This is wrong and can potentially create black holes
or routing loops according to Dave Katz and Acee Lindem at ospf@ietf.org
Even if the current code could be proved to be harmless in all cases,
it adds substantial extra processing and memory allocations.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
OSPF really needs to specify interface in its routes. Otherwise
ospf may change the wrong route.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
[fixed up some whitespace errors, split patch in two]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
This is better than a prefix lookup as prefixes may not be
unique, that is, the same prefix can exist on several interfaces.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
Maintain router LSA positions in OSPF interface.
Find the OSPF interface in nexthop_calculation using
the position in the router LSA. This is possible because
the only time nexthop_calculation needs to look up interfaces
is when dealing with its own Router LSA.
This has the following advantages:
- Multiple PtP interfaces with the same IP address between two routers.
- Use Unnumbered PtP on just one end of the link.
- Faster OI lookup for the OSPF interface and only
done once for PtoP links.
*ospf_interface.h: (struct ospf_interface) Add storage for
storing router LSA position.
*ospf_interface.c: (ospf_if_lookup_by_lsa_pos)
lookup OSPF I/F in an area using LSA position.
*ospf_lsa.c: (router_lsa_link_set) record Router LSA position.
*ospf_spf.c: (ospf_spf_next) Count and pass along lsa position.
(ospf_nexthop_calculation) Add lsa position argument.
call ospf_if_lookup_by_lsa_pos() for OSFP interface handle.
Clean up and remove all calls ospf_if_is_configured() the
rest. Adjust a few debug logs.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
This was found in scale testing at OSR; ospfd is adding the same link
over and over again to the SPF tree. This fix prevents the resulting
memory corruption from happening and adds a debug message to track
occurence of this issue and/or confirm a proper fix.
(This version was improved by Scott Feldman over the earlier RFC.)
* ospfd/ospf_spf.c: (ospf_spf_add_parent) loop over existing vertices
and refuse to add duplicates.
Tested-by: Martin Winter <mwinter@opensourcerouting.org>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
|
|
Most table handlers do not expect to be given an OID whose prefix is
outside what they can handle. This is not a problem with the SMUX
implementation since it always correct the OID such that the prefix
matches. However, this is not the case for the AgentX
implementation. A new function, smux_header_table() is used to do this
normalization.
|
|
smux_trap() signature has been changed to provide appropriate level
information to send SNMPv2 notifications. This includes the addition
of the enterprise OID to use (from which is derived the SNMP trap OID)
and the MIB registry to locate the appropriate function for variable
bindings provided by the trap.
The SMUX implementation has been updated but ignore the provided
enterprise OID. Instead, it still uses the SMUX peer OID to keep
compatibility with previous versions of Quagga. The SMUX
implementation also ignores the provided MIB registry since it uses
smux_get() function to grab the appropriate values. This is not
possible with the AgentX implementation since there is no such
function provided by NetSNMP.
|
|
This element was not unused.
|
|
smux_trap() contains an argument whose use appears to be to set
sysUpTime.0/timestamp field in SNMP trap. However, this value is not
used in smux_trap(). Moreover, it is expected that this field is the
value of sysUpTime.0 when the trap was sent and not any other time
related to the trap. To avoid any confusion, we remove this field from
the signature of the function.
|
|
The correct method to link to NetSNMP is to use net-snmp-config (which
is like pkg-config). Explicit link to libcrypto is also dropped
(NetSNMP libs are linked to libcrypto, no need to link Quagga to
it). Moreover, @SNMP_INCLUDES@ is dropped because useless. Due to a
bug in configure.ac, it was properly populated.
|
|
NetSNMP is the only SNMP implementation for Quagga. We don't need two
different symbols.
|
|
Some .h files in lib/ are autogenerated. The search path should
include the build directory and the source directory. They usually
match but sometimes, they may be different. For example:
$ mkdir build
$ cd build
$ ../configure
$ make
|
|
- And allows to walk the LSDB.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
|
|
|
|
Protocol version checks fits ospf_packet_examin() better (like it is
implemented in ospf6d), and packet type check is already there.
|
|
The old ospf_check_auth() function did two different jobs depending on
AuType. For Null and Simple cases it actually authenticated the packet,
but for Cryptographic case it only checked declared packet size (not
taking the actual number of bytes on wire into account). The calling
function, ospf_verify_header(), had its own set of MD5/checksum checks
dispatched depending on AuType.
This commit makes the packet size check work against the real number of
bytes and moves it to ospf_packet_examine(). All MD5/checksum
verification is now performed in ospf_check_auth() function.
* ospf_packet.c
* ospf_packet_examin(): check length with MD5 bytes in mind
* ospf_verify_header(): remove all AuType-specific code
* ospf_check_auth(): completely rewrite
|
|
|
|
An OSPFv2 packet with trailing data blocks (authentication and/or
link-local signaling) failed the recently implemented packet length
check, because trailing data length isn't counted in the packet header
"length" field. This commit fixes respective check conditions.
* ospf_packet.c
* ospf_packet_examin(): use "bytesdeclared" instead of "bytesonwire"
|
|
This commit ports more packet checks to OSPFv2, in particular, LSA size
verification and Router-LSA link blocks verification.
* ospf_lsa.h: add LSA size macros
* ospf_packet.h: add struct ospf_ls_update
* ospf_packet.c
* ospf_lsa_minlen[]: a direct equivalent of ospf6_lsa_minlen[]
* ospf_router_lsa_links_examin(): new function, verifies trailing
part of a Router-LSA
* ospf_lsa_examin(): new function like ospf6_lsa_examin()
* ospf_lsaseq_examin(): new function like ospf6_lsaseq_examin()
* ospf_packet_examin(): add type-specific deeper level checks
|
|
Rewrite some pointer arithmetics without the additional variables and
move byte order conversion inside the function.
|
|
1. The only purpose of "ibuf" argument was to get stream size, which
was always equal to OSPF_MAX_PACKET_SIZE + 1, exactly as initialized
in ospf_new().
2. Fix the packet size check condition, which was incorrect for very
large packets, at least in theory.
|
|
This commit ports some of the OSPFv3 packet reception checks
to OSPFv2.
* ospf_packet.c
* ospf_packet_minlen[]: a direct equivalent of ospf6_packet_minlen[]
* ospf_packet_examin(): new function designed after the first part
of ospf6_packet_examin()
* ospf_read(): verify received packet with ospf_packet_examin()
* ospf_packet.h: add convenience macros
|
|
|
|
* ospf_packet.h: add proper str/max extern declarations
* ospf_packet.c
* ospf_packet_type_str: rewrite in "struct message", add max value
* ospf_packet_add(): use LOOKUP()
* ospf_write(): ditto
* ospf_hello(): ditto
* ospf_read(): ditto
* ospf_dump.h: the declaration does not belong here
* ospf_dump.c
* ospf_header_dump(): use LOOKUP()
* show_debugging_ospf(): ditto
|
|
The previous commits modified both zebra and bgpd for additional
SAFI field, but not any other routing daemon, which led to zebra
daemon crashing with failed assertion.
|
|
|
|
The function is implemented in ospf_lsa.c, move its "extern" declaration
to ospf_lsa.h for consistency.
|
|
* ospf_ase.c
* ospf_ase_complete_direct_routes(): dismiss unused variable
|
|
* (general) Move functions in headers into files, to be compiled into
shared object files. Remove inline qualifier from functions. Let the
compiler do the work.
|
|
...otherwise 4294967295 is not a valid value on 32bit systems
|
|
* ospf_abr.c
* ospf_abr_nssa_am_elected(): feed "best" instead of "address of best"
into IPV4_ADDR_CMP(), because "best" is a pointer; also, mean s_addr
field of the structures to get better typed pointers
|
|
* ospf_packet.c (ospf_recv_packet): FreeBSD, starting from version 10, will not
subtract the IP header size from ip_len.
This is the patch from FreeBSD's ports/net/quagga/files/patch-ospfd__ospf_packet.c,
by Boris Kovalenko.
|
|
|
|
this replaces most occurences of routing protocol lists by preprocessor
defines from route_types.h. the latter is autogenerated from
route_types.txt by a perl script (previously awk). adding a routing
protocol now is mostly a matter of changing route_types.txt and log.c.
Conflicts:
lib/route_types.awk
|
|
|
|
|
|
All daemons modified to support custom path to zserv
socket.
lib: generalize a zclient connection
zclient_socket_connect added. zclient_socket and
zclient_socket_un were hidden under static expression.
"zclient_serv_path_set" modified.
|
|
The code for nssa_range and other bits that were written but
never used.
|
|
The old algorithim looked up every node twice as it withdrew
the entry. It looks up entry once in redistribute_withdraw, then
looks it up again info_delete. Use result of first lookup
to do the free directly.
This may explain the slow performance observed in
https://bugzilla.vyatta.com/show_bug.cgi?id=4421
|
|
Make ospf_flood() propagate error returned by ospf_lsa_install() further
to properly discard the malformed LSA, not just prevent the immediate
crash.
|
|
commit '717750433839762d23a5f8d88fe0b4d57c8d490a' causes SEGV error,
when 'oi = ospf_if_lookup_recv_if (ospf, iph->ip_src, ifp);' returns
NULL.
* ospf_packet.c
* ospf_read(): change a place of calling 'ospf_verify_header()'
|
|
|
|
|
|
|
|
* ospf_spf.c
* ROUTER_LSA_TOS_SIZE: prepend OSPF_ and move to ospf_lsa.h
* ROUTER_LSA_MIN_SIZE: replace with existing OSPF_ROUTER_LSA_LINK_SIZE
|
