| Age | Commit message (Collapse) | Author |
|---|
|
* ripd.h: Add define for the RIPv2 Authentication Data family
Move the auth type defines up to where other defines live.
Add RIP_AUTH_MD5_COMPAT_SIZE, for backwards compatible
md5->auth_len size. Add md5_auth_len field to struct
rip_interface: (rip_interface_new) Init md5_auth_len to compatible
size.
(ip_rip_authentication_mode_cmd) Extended to handle setting
md5 auth-length. Appropriate aliases added.
(no_ip_rip_authentication_mode_cmd) Reset md5_auth_len to
compatible size.
(rip_interface_config_write) Teach it about md5_auth_len.
_always_ write out the auth-length, so that everyone will get
the setting in their config file, and hence allow for a future
change of default for md5_auth_len to be less painful - every md5
user will have this setting in their config file.
ripd.c: (rip_packet_dump) Change nasty hard coded constants to
symbolic defines. Change various tests of 'ntoh.(variable) ==
constant' to test 'variable == ntoh.(constant)'. Clean up
indentation on some long lines.
(rip_auth_simple_password) ditto.
(rip_auth_md5) ditto, also add length argument and sanity check
md5 data offset field. Sanity check md5 auth length, accept RFC
or old-ripd/cisco lengths.
(rip_auth_md5_set) as per (rip_packet_dump), also write out
the configured md5 auth length for the interface (old-ripd or rfc)
(rip_read) as per (rip_packet_dump)
(rip_write_rte) ditto
(rip_response_process) ditto
(rip_write_rte) ditto
|
|
|
|
* ripd.c: Interoperability fix. Correct value for MD5 auth length
is 16. Accept packets with this set to >= 16, and set to 16
ourselves.
|
|
* ripd.c: Fixup compile warnings
* rip_routemap.c: Ditto
|
|
* bgp_zebra.c: (bgp_interface_address_add) sync to zclient changes
(bgp_interface_address_delete) ditto.
(bgp_zebra_announce) ditto.
(bgp_zebra_withdraw) ditto.
* isis_zebra.c: Sync with zclient changes.
* zclient.c (zapi_ipv4_route) Follow Sowmini's lead and describe
message format.
* ospf6_zebra.c: Sync to zclient changes
* ospf_zebra.c: Sync with lib/zclient changes
* rip_zebra.c: sync with zclient changes.
* rip_interface.c: ditto.
* ripng_{interface,zebra}.c: sync with zclient changes
2004-05-08 Sowmini Varadhan <sowmini.varadhan@sun.com>
* zclient.c: (zapi_ipv4_add) collapsed into zapi_ipv4_route
(zapi_ipv4_delete) ditto.
(zapi_ipv4_route) add/delete a route by way of cmd arg.
(zapi_ipv6_add) collapsed into zapi_ipv6_route.
(zapi_ipv6_delete) ditto.
(zapi_ipv6_route) add/delete a route by way of cmd arg.
(zebra_interface_address_delete_read) collapsed into
zebra_interface_address_read.
(zebra_interface_address_delete_read) ditto.
(zebra_interface_address_read) read address add/delete messages
by way of type argument. Describe command message format.
(zebra_interface_add_read) Unconditionally read new ifmtu6 field.
Describe command message format.
(zebra_interface_state_read) Unconditionally read new ifmtu6 field.
(zclient_redistribute_set) Collapsed into zclient_redistribute
(zclient_redistribute_unset) ditto
(zclient_redistribute) set/unset redistribution.
(zclient_redistribute_default_set) Collapsed into
zclient_redistribute_default.
(zclient_redistribute_default_unset) ditto.
(zclient_redistribute_default) Redistribute default set/unset.
* zclient.h: delete zapi_ipv{4,6}_add, zapi_ipv{4,6}_delete. Add
zapi_ipv{4,6}_route. delete zclient_redistribute_set/unset. Add
zclient_redistribute. Ditto for
zclient_redistribute_default_{set/unset}.
|
|
* ripd.c: (rip_update_jitter) Bound jitter to a more sensible
value, eg 1/4 of update time.
|
|
* ripd.c: (rip_rte_process) fix typo in merge of previous patch
and run function through indent.
|
|
* ripd.c: make ripd also check on administrative distance of his
own links to update routes.
|
|
|
|
|
|
|
|
|
|
* (many) reference <lib/version.h> rather than "version.h",
because version.h is a generated file and not present in the
source tree when using objdir builds.
(committed by gdt)
works fine with normal builds; didn't try objdir
|
|
|
|
|
|
|
|
* rip_interface.c: obsolete unbind code in
rip_interface_multicast_set, and instead do the more portable
(though slower) method of creating a socket for each outgoing packet
and binding the source address on the new socket.
* rip_interface.c, ripd.c, ripd.h: Modify rip_request_send so that
source address is determined by the caller of rip_request_send for
ripv1 packets and non-multicast interfaces (rip_request_send loops
over all connected address in all other cases).
* rip_send_packet: don't send packets with source set to
ZEBRA_IFA_SECONDARY connected addresses; improved debug messages;
|
|
* tests/test-sig.c: New file, regression test for sigevents.
* lib/Makefile.am: add sigevent.{c,h}
* (isis|rip|ripng|ospf|ospf6|bgp)d/\1_main.c: modify for sigevents.
* zebra/main.c: ditto.
|
|
files, defaulting to sysconfdir (matching previous behavior).
This is needed to support (cleanly) NetBSD pkgsrc, which requires that
example config files go in $(prefix)/share/examples/pkgname, rather
than in $(prefix)/etc/pkgname.
|
|
* ripd/ripd.c: rip_output_process() fixup aspects of split-horizon
route suppression. See [quagga-dev 429].
|
|
* ripd/ripd.c: rip_create_socket() privs were not dropped if bind
failed.
|
|
* configure.ac: Check for fcntl()
* {bgpd,ospf,ospf6d,ripd,ripngd}/Makefile.am: Install conf file via
regular automake means, not magic install incantations, see
bug #38.
* lib/Makefile.am: install the headers, needed to link libzebra.a
(and hence libospf.a, OSPF-API, etc.)
|
|
* ripd/ripd.c: (rip_send_packet) use rip->sock for mcast sends,
instead of creating one socket per send. send source addr to
rip_update_interface.
(rip_update_process) should send an update on every connected
network for each interface.
(rip_request_send) should send a request on every connected
network for each interface.
* ripd/ripd.h: update prototype for rip_interface_multicast_set
* ripd/rip_interface.c: (rip_interface_multicast_set) reorganized
so that it can be called repeatedly for aliased interfaces (on
multiple networks).
|
|
* zebra/connected.c: revert the 'generic PtP' patch as it causes
far too many problems. People who use FreeSWAN should investigate
native linux ipsec.
* zebra/rt_netlink.c: ditto
* lib/if.c: ditto
* ripd/ripd.h: ditto
* ripd/ripd.c: ditto
* ripd/rip_interface.c: ditto
* ospfd/ospfd.c: ditto
* ospfd/ospf_snmp.c: ditto
* bgpd/bgp_nexthop.c: ditto
|
|
* rip_interface.c: (rip_interface_address_add) call
rip_enable_apply(), or the interface is never considered up.
see [quagga-dev 225].
|
|
* zebra/main.c: Fixup ZEBRA_{GROUP,USER} defines ->
QUAGGA_{USER,GROUP}
* bgpd/bgp_main.c: ditto
* ospf6d/ospf6_main.c: ditto
* ospfd/ospf_main.c: ditto
* ripd/rip_main.c: ditto
* ripngd/ripng_main.c: ditto
* zebra/main.c: ditto
|
|
* Add missing 'i' to getopts, short form of --pid_file.
see http://bugzilla.quagga.net/show_bug.cgi?id=25
|
|
* rip_interface.c: add 'default' to passive-interface command DEFUN
|
|
* Fix lib/smux.c's reliance on daemons exporting struct
thread_master *master.
|
|
* lib/vty.{c,h}: Remove vty layer depending on a 'master' global,
pass the thread master in explicitly to vty_init. Sort out some
header dependency problems with lib/command.h
* zebra/: Move globals to struct zebrad. Update vty_init().
* (.*)/\1_main.c: update call to vty_init().
|
|
Compile and warning fixes for the ripd 'passive-interface default' patch.
|
|
Subject: [zebra 12403] patch for ripd to accept any version of RIP
by default
The default Cisco IOS behavior is to send RIP version 1 packets and receive
version 1 and version 2 packets. But zebra version 0.92a sends and receives
only version 2 packets by default.
I have patched the code to change zebra's default behavior to sending
version 2 packets (same as before) but receiving both versions. While
this is still not identical to Cisco's behavior, it does now accept
packets of both versions and retains backwards compatibility with
zebra configurations.
|
|
Subject: [zebra 12406] patch for ripd to support "passive-interface
default" behavior
In Cisco IOS, the router rip passive-interface subcommand can accept
an interface name of "default". In that cases, all interfaces are set
to be passive by default, and you must explicitly make it non-passive
by using the "no passive-interface <ifname>" command if you want updates
to go to that interface.
<command implemented for zebra>
|
|
* Merge of zebra privileges
|
|
|
|
|
|
|
|
|
|
http://hasso.linux.ee/zebra/ht-routemap-18042003_5.patch
Trivial fixes to sync daemon's route-map commands to have same syntax. Fixes
a lot of errors with "match ..." and "set ..." commands when using vtysh.
|
|
Add ospfclient to ospfclient/.cvsignore
|
|
moved definition of the various socket paths from the
per daemon header files into configure.ac. it will set the paths to
be in the directory specified by --localstatedir=<prefix> or
otherwise will try to guess as best it can ( a la pid file path
detection - which probably should try reference ${prefix} too).
the present hardcoded socket path, /tmp, isnt really correct. should
be in /var somewhere really.
|
|
Developers working with the repository should have the appropriate tools.
Out-of-sync files cause far too many problems with users as well as auto*
scripts not being half as portable across systems as they ought to be.
make-dist exists for a reason.
Todo: make the CVS snapshot script do make-dist, and use the resulting
tarball as the snapshot.
|
|
* sync to latest zebra CVS
* spec file: updated and added define for ospf-api/client
NB: OSPF-API has been broken by the zebra.org changes, which
has added struct ospf * as a new arg to many functions
|
|
|
|
No doubt builds will now break for everyone. (works here - autoconf 2.13)
|
|
|
|
|
|
|
|
[zebra 17290] [PATCHES] - Fixes for problems in 0.93b
portfix patch
|
|
|
