blob: 20a92a91606c01c69a01a2ae3fdf44933720263f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
|
#!/bin/bash
# Public domain, not copyrighted..
NUM=5
VTYBASE=2610
ASBASE=64560
BGPD=/path/to/bgpd
PREFIX=192.168.145.
#PREFIX=3ffe:123:456::
ADDRPLEN=32
CONFBASE=/tmp
PIDBASE=/var/run/quagga
CHOWNSTR=quagga:quagga
for H in `seq 1 ${NUM}` ; do
CONF="${CONFBASE}"/bgpd${H}.conf
ADDR=${PREFIX}${H}
if [ ! -e "$CONF" ] ; then
# This sets up a ring of bgpd peerings
NEXT=$(( ($H % ${NUM}) + 1 ))
PREV=$(( (($H + $NUM - 2) % ${NUM}) + 1 ))
NEXTADDR="${PREFIX}${NEXT}"
NEXTAS=$((${ASBASE} + $NEXT))
PREVADDR="${PREFIX}${PREV}"
PREVAS=$((${ASBASE} + $PREV))
ASN=$((64560+${H}))
# Edit config to suit.
cat > "$CONF" <<- EOF
password whatever
service advanced-vty
!
router bgp ${ASN}
bgp router-id ${ADDR}
network 10.${H}.1.0/24 pathlimit 1
network 10.${H}.2.0/24 pathlimit 2
network 10.${H}.3.0/24 pathlimit 3
neighbor default peer-group
neighbor default update-source ${ADDR}
neighbor default capability orf prefix-list both
neighbor default soft-reconfiguration inbound
neighbor default route-map test out
neighbor ${NEXTADDR} remote-as ${NEXTAS}
neighbor ${NEXTADDR} peer-group default
neighbor ${PREVADDR} remote-as ${PREVAS}
neighbor ${PREVADDR} peer-group default
!
address-family ipv6
network 3ffe:${H}::/48
network 3ffe:${H}:1::/48 pathlimit 1
network 3ffe:${H}:2::/48 pathlimit 3
network 3ffe:${H}:3::/48 pathlimit 3
neighbor default activate
neighbor default capability orf prefix-list both
neighbor default default-originate
neighbor default route-map test out
neighbor ${NEXTADDR} peer-group default
neighbor ${PREVADDR} peer-group default
exit-address-family
!
! bgpd still has problems with extcommunity rt/soo
route-map test permit 10
set extcommunity rt ${ASN}:1
set extcommunity soo ${ASN}:2
set community ${ASN}:1
line vty
!
end
EOF
chown ${CHOWNSTR} "$CONF"
fi
# You may want to automatically add configure a local address
# on a loop interface.
#
# Solaris: ifconfig vni${H} plumb ${ADDR}/${ADDRPLEN} up
# Linux: ip address add ${ADDR}/${ADDRPLEN} dev lo 2> /dev/null
${BGPD} -i "${PIDBASE}"/bgpd${H}.pid \
-l ${ADDR} \
-f "${CONF}" \
-P $((${VTYBASE}+${H})) \
-d
done
|
