diff options
| -rw-r--r-- | README | 2 | ||||
| -rw-r--r-- | Tonokip_Firmware/configuration.h | 1 | ||||
| -rw-r--r-- | Tonokip_Firmware/pins.h | 57 |
3 files changed, 52 insertions, 8 deletions
@@ -1,3 +1,5 @@ +The leading developers of Sprinter are currently Kliment and caru, though many others contribute with their patches.
+
This is a firmware for RAMPS and other reprap single-processor electronics setups. It supports printing from SD card, active heatbed control, and ATmega internal pullups.
This work is licensed under the GNU GPL v3 or (at the user's discretion) any later version.
diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h index a658412..2bd4e6a 100644 --- a/Tonokip_Firmware/configuration.h +++ b/Tonokip_Firmware/configuration.h @@ -93,6 +93,7 @@ float e_steps_per_unit = 16; float max_feedrate = 200000; //mmm, acceleration! float max_z_feedrate = 120; +//For SAE Prusa mendeel float z_steps_per_unit = should be 3200/1.411 for 5/16-18 rod and 3200/1.058 for 5/16-24 //float x_steps_per_unit = 10.047; //float y_steps_per_unit = 10.047; //float z_steps_per_unit = 833.398; diff --git a/Tonokip_Firmware/pins.h b/Tonokip_Firmware/pins.h index fe5f1f7..79adaaa 100644 --- a/Tonokip_Firmware/pins.h +++ b/Tonokip_Firmware/pins.h @@ -206,11 +206,55 @@ #endif #endif +// uncomment one of the following lines for RAMPS v1.3 or v1.0, comment both for v1.2 or 1.1 +// #define RAMPS_V_1_3 +// #define RAMPS_V_1_0 + + +#ifdef RAMPS_V_1_3 + +#define X_STEP_PIN 54 +#define X_DIR_PIN 55 +#define X_ENABLE_PIN 38 +#define X_MIN_PIN 3 +#define X_MAX_PIN 2 + +#define Y_STEP_PIN 60 +#define Y_DIR_PIN 61 +#define Y_ENABLE_PIN 56 +#define Y_MIN_PIN 14 +#define Y_MAX_PIN 15 + +#define Z_STEP_PIN 46 +#define Z_DIR_PIN 48 +#define Z_ENABLE_PIN 62 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +#define E_STEP_PIN 26 +#define E_DIR_PIN 28 +#define E_ENABLE_PIN 24 + +#define SDPOWER -1 +#define SDSS 53 +#define LED_PIN 13 +#define FAN_PIN 9 +#define PS_ON_PIN 12 +#define KILL_PIN -1 + +#define HEATER_0_PIN 10 +#define HEATER_1_PIN 8 +#define TEMP_0_PIN 13 // ANALOG NUMBERING +#define TEMP_1_PIN 14 // ANALOG NUMBERING + + +#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default + #define X_STEP_PIN 26 #define X_DIR_PIN 28 #define X_ENABLE_PIN 24 #define X_MIN_PIN 3 -#define X_MAX_PIN -2 //2 +#define X_MAX_PIN -1 //2 #define Y_STEP_PIN 38 #define Y_DIR_PIN 40 @@ -231,28 +275,25 @@ #define SDPOWER 48 #define SDSS 53 #define LED_PIN 13 - #define PS_ON_PIN -1 #define KILL_PIN -1 -// uncomment the following line for RAMPS V1.0 -// #define RAMPS_V_1_0 -#ifdef RAMPS_V_1_0 + +#ifdef RAMPS_V_1_0 // RAMPS_V_1_0 #define HEATER_0_PIN 12 // RAMPS 1.0 #define HEATER_1_PIN -1 // RAMPS 1.0 - #define FAN_PIN 11 // RAMPS 1.0 -#else // RAMPS_V_1_1 as default +#else // RAMPS_V_1_1 or RAMPS_V_1_2 #define HEATER_0_PIN 10 // RAMPS 1.1 #define HEATER_1_PIN 8 // RAMPS 1.1 - #define FAN_PIN 9 // RAMPS 1.1 #endif #define TEMP_0_PIN 2 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! #define TEMP_1_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! +#endif // SPI for Max6675 Thermocouple |