diff options
Diffstat (limited to 'Tonokip_Firmware/Makefile')
| -rw-r--r-- | Tonokip_Firmware/Makefile | 28 |
1 files changed, 13 insertions, 15 deletions
diff --git a/Tonokip_Firmware/Makefile b/Tonokip_Firmware/Makefile index d847f13..7f4f23e 100644 --- a/Tonokip_Firmware/Makefile +++ b/Tonokip_Firmware/Makefile @@ -1,35 +1,33 @@ +# Sprinter Arduino Project Makefile +# +# Makefile Based on: # Arduino 0011 Makefile # Arduino adaptation by mellis, eighthave, oli.keller # +# This has been tested with Arduino 0022. +# # This makefile allows you to build sketches from the command line # without the Arduino environment (or Java). # # Detailed instructions for using the makefile: # -# 1. Copy this file into the folder with your sketch. There should be a -# file with the same name as the folder and with the extension .pde -# (e.g. foo.pde in the foo/ folder). -# -# 2. Modify the line containg "INSTALL_DIR" to point to the directory that +# 1. Modify the line containg "INSTALL_DIR" to point to the directory that # contains the Arduino installation (for example, under Mac OS X, this # might be /Applications/arduino-0012). # -# 3. Modify the line containing "PORT" to refer to the filename +# 2. Modify the line containing "PORT" to refer to the filename # representing the USB or serial connection to your Arduino board # (e.g. PORT = /dev/tty.USB0). If the exact name of this file # changes, you can use * as a wildcard (e.g. PORT = /dev/tty.usb*). # -# 4. Set the line containing "MCU" to match your board's processor. +# 3. Set the line containing "MCU" to match your board's processor. # Older one's are atmega8 based, newer ones like Arduino Mini, Bluetooth # or Diecimila have the atmega168. If you're using a LilyPad Arduino, # change F_CPU to 8000000. # -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. +# 4. Type "make" and press enter to compile/verify your program. # -# 7. Type "make upload", reset your Arduino board, and press enter to +# 5. Type "make upload", reset your Arduino board, and press enter to # upload your program to the Arduino board. # # $Id$ @@ -39,7 +37,7 @@ INSTALL_DIR = /home/chris/arduino-0022 UPLOAD_RATE = 38400 AVRDUDE_PROGRAMMER = stk500v1 PORT = /dev/ttyUSB0 -MCU = atmega644p +MCU = atmega2560 F_CPU = 16000000 @@ -53,7 +51,7 @@ $(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \ $(ARDUINO)/wiring_pulse.c $(ARDUINO)/wiring_serial.c \ $(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \ -$(ARDUINO)/Print.cpp +$(ARDUINO)/Print.cpp ./SdFile.cpp ./SdVolume.cpp ./Sd2Card.cpp FORMAT = ihex @@ -95,7 +93,7 @@ LDFLAGS = -lm # Programming support using avrdude. Settings and variables. AVRDUDE_PORT = $(PORT) AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf \ +AVRDUDE_FLAGS = -V -F -C $(INSTALL_DIR)/hardware/tools/avrdude.conf \ -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ -b $(UPLOAD_RATE) |