diff options
Diffstat (limited to 'Tonokip_Firmware')
| -rw-r--r-- | Tonokip_Firmware/Tonokip_Firmware.pde | 36 |
1 files changed, 11 insertions, 25 deletions
diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde index 70a4ac9..5faf413 100644 --- a/Tonokip_Firmware/Tonokip_Firmware.pde +++ b/Tonokip_Firmware/Tonokip_Firmware.pde @@ -48,7 +48,6 @@ // M84 - Disable steppers until next move, // or use S<seconds> to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. // M85 - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default) -// M86 - If Endstop is Not Activated then Abort Print. Specify X and/or Y // M92 - Set axis_steps_per_unit - same syntax as G92 // M115 - Capabilities string // M140 - Set bed target temp @@ -769,10 +768,6 @@ inline void process_commands() code_seen('S'); max_inactive_time = code_value() * 1000; break; - case 86: // M86 If Endstop is Not Activated then Abort Print - if(code_seen('X')) if( digitalRead(X_MIN_PIN) == ENDSTOPS_INVERTING ) kill(3); - if(code_seen('Y')) if( digitalRead(Y_MIN_PIN) == ENDSTOPS_INVERTING ) kill(4); - break; case 92: // M92 if(code_seen('X')) x_steps_per_unit = code_value(); if(code_seen('Y')) y_steps_per_unit = code_value(); @@ -1394,9 +1389,8 @@ inline void manage_heater() target_raw = 0; #endif #ifdef MAXTEMP - if(current_raw > maxttemp) { - // We are too hot. Emergency brake to protect hotend - kill(5); + if(current_raw >= maxttemp) { + target_raw = 0; } #endif #if (TEMP_0_PIN > -1) || defined (HEATER_USES_MAX66675) @@ -1582,11 +1576,16 @@ float analog2tempBed(int raw) { #endif } -inline void kill(byte debug) +inline void kill() { - if(HEATER_0_PIN > -1) digitalWrite(HEATER_0_PIN,LOW); + #if TEMP_0_PIN > -1 + target_raw=0; + digitalWrite(HEATER_0_PIN,LOW); + #endif + #if TEMP_1_PIN > -1 + target_bed_raw=0; if(HEATER_1_PIN > -1) digitalWrite(HEATER_1_PIN,LOW); - + #endif disable_x(); disable_y(); disable_z(); @@ -1594,22 +1593,9 @@ inline void kill(byte debug) if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); - while(1) - { - switch(debug) - { - case 1: Serial.print("Inactivity Shutdown, Last Line: "); break; - case 2: Serial.print("Linear Move Abort, Last Line: "); break; - case 3: Serial.print("Homing X Min Stop Fail, Last Line: "); break; - case 4: Serial.print("Homing Y Min Stop Fail, Last Line: "); break; - case 5: Serial.print("Hot-end overheat protection, Last Line: "); break; - } - Serial.println(gcode_LastN); - delay(5000); // 5 Second delay - } } inline void manage_inactivity(byte debug) { -if( (millis()-previous_millis_cmd) > max_inactive_time ) if(max_inactive_time) kill(debug); +if( (millis()-previous_millis_cmd) > max_inactive_time ) if(max_inactive_time) kill(); if( (millis()-previous_millis_cmd) > stepper_inactive_time ) if(stepper_inactive_time) { disable_x(); disable_y(); disable_z(); disable_e(); } } |