summaryrefslogtreecommitdiff
path: root/Sprinter/Sprinter.pde
AgeCommit message (Expand)Author
2012-06-27refactor eeprom routines to make it possible to modify the value of a single ...Felipe Corrêa da Silva Sanches
2012-06-18reimplement homing routine as an inline functionFelipe Corrêa da Silva Sanches
2012-06-18refactoring homing routine to avoid copy&pasted codeFelipe Corrêa da Silva Sanches
2012-06-15fix a few typos and correct english usageFelipe Corrêa da Silva Sanches
2012-06-14Merge pull request #186 from blddk/experimentalmidopple
2012-06-14Forgot to pit the part in where it makes the pin an output pin... >.<blddk
2012-06-12Version 1.3.19Tmidopple
2012-06-11Merge pull request #183 from kliment/mastermidopple
2012-06-11Error with Command M201, when this Command is use the same Values are written...midopple
2012-06-07Added M400blddk
2012-05-24Too many if('sblddk
2012-05-17Merge pull request #171 from kliment/mastermidopple
2012-05-16If a small move is drop and the next move is retract the speed is wrong calcu...midopple
2012-05-04Version 1.3.17Tmidopple
2012-05-01Merge pull request #168 from kliment/mastermidopple
2012-04-30Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID isOhmEye
2012-04-24Extra Retract Feedrate for Extrudermidopple
2012-04-23Ignore ":" in comments.midopple
2012-04-22Version 1.3.15Tmidopple
2012-04-20When endstop is hit count virtual steps, so the print lose no position when e...midopple
2012-04-20- Extrudmultiply with code M221 Sxxx (S100 original Extrude value)midopple
2012-04-01Merge pull request #161 from se5a/masterkliment
2012-04-02Added M93 command. sends current steps for all axis se5a
2012-03-30Merge pull request #160 from kliment/masterkliment
2012-03-30Command M106 / M107 for control the fan can use PWM midopple
2012-03-28Merge from experimental, thanks to triffid_huntermidopple
2012-03-28fix enable_endstops being used before its definitionMichael Moon
2012-03-27Fixed arc offsetmidopple
2012-03-19Fixes virtual endstops when using mixed physical endstop positions.midopple
2012-03-19Version 1.3.11Tmidopple
2012-03-14ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared midopple
2012-03-12calculate feedrate without extrude before planner block is setmidopple
2012-03-04Move SLOWDOWN Funktion up, at the current position does not workmidopple
2012-02-24If a line starts with ';', it is ignored but comment_mode is reset.midopple
2012-02-24Version 1.3.07Tmidopple
2012-02-17The microcontroller can store settings to EEPROMmidopple
2012-02-15- changed homing function to not conflict with min_software_endstops/max_soft...midopple
2012-02-05- Implement Plannercode from Marlin V1 --> big thanks to Erikmidopple
2012-01-29Add function to check the UART buffer while arc function is workingmidopple
2012-01-29Update Changelog in Mainfilemidopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
2012-01-29Change infotextmidopple
2012-01-29New Version Sprinter V2midopple
2012-01-22Reported wrong temperature while heating upblddk
2012-01-22Changed temperature table for bed, to the one for the bed, instead of for the...blddk
2012-01-22Added option to set a delay after enabeling stepper driver, to allow the driv...blddk
2011-12-06Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 board...Greg Dahlman
2011-12-04Added an option to make init.g on SD run on boot.Nathan Zadoks
2011-11-16M30/M31 fast sd block transferPhilip Kin
2011-11-16M30/M31 fast sd block transferPhilip Kin
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-22 09:29:39 +0000