summaryrefslogtreecommitdiff
path: root/Sprinter/Sprinter.pde
AgeCommit message (Expand)Author
2012-06-11Error with Command M201, when this Command is use the same Values are written...midopple
2012-05-16If a small move is drop and the next move is retract the speed is wrong calcu...midopple
2012-04-30Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID isOhmEye
2012-03-30Command M106 / M107 for control the fan can use PWM midopple
2012-03-28fix enable_endstops being used before its definitionMichael Moon
2012-03-19Fixes virtual endstops when using mixed physical endstop positions.midopple
2012-03-19Version 1.3.11Tmidopple
2012-03-14ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared midopple
2012-03-12calculate feedrate without extrude before planner block is setmidopple
2012-03-04Move SLOWDOWN Funktion up, at the current position does not workmidopple
2012-02-24If a line starts with ';', it is ignored but comment_mode is reset.midopple
2012-02-24Version 1.3.07Tmidopple
2012-02-17The microcontroller can store settings to EEPROMmidopple
2012-02-15- changed homing function to not conflict with min_software_endstops/max_soft...midopple
2012-02-05- Implement Plannercode from Marlin V1 --> big thanks to Erikmidopple
2012-01-29Add function to check the UART buffer while arc function is workingmidopple
2012-01-29Update Changelog in Mainfilemidopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
2012-01-29Change infotextmidopple
2012-01-29New Version Sprinter V2midopple
2012-01-22Reported wrong temperature while heating upblddk
2012-01-22Changed temperature table for bed, to the one for the bed, instead of for the...blddk
2012-01-22Added option to set a delay after enabeling stepper driver, to allow the driv...blddk
2011-12-06Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 board...Greg Dahlman
2011-12-04Added an option to make init.g on SD run on boot.Nathan Zadoks
2011-11-16M30/M31 fast sd block transferPhilip Kin
2011-11-16M30/M31 fast sd block transferPhilip Kin
2011-11-06osc reductionChris Dieringer
2011-10-29Fix d calculation on XYZ moves where comparison was inside of abs() instead o...barclayo
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Update Sprinter/Sprinter.pdeblddk
2011-10-16Added function for controlling controller cooling fanblddk
2011-10-01Merge branch 'master' of github.com:kliment/Sprinter into experimentalKliment Yanev
2011-09-28Fix scoping problem (fixes issue #70)Guillaume Seguin
2011-09-18Revert "Merge pull request #95 from AxTheB/master"Kliment Yanev
2011-09-18Merge pull request #95 from AxTheB/masterkliment
2011-09-17line numbers ale long, not intVáclav 'ax' Hůla
2011-09-17simplified string-to-number conversionsVáclav 'ax' Hůla
2011-09-17fixed typo, added even more PID improvements (these settings work out of box ...Keegi
2011-09-17PID fixesKeegi
2011-09-17Reset heater pins after hard resets to avoid keeping them enabled while we do...Alessandro Ranellucci
2011-09-17Merge remote branch 'upstream/experimental' into alarm-pinAlessandro Ranellucci
2011-09-17Signal an optional ALARM_PIN when reaching MAXTEMPAlessandro Ranellucci
2011-09-17Initialize LED pin (was stuck after hard resets)Alessandro Ranellucci
2011-09-11Fix temp readings for multiple sensor types.unknown
2011-09-08Merge branch 'master' of github.com:kliment/Sprinter into experimentalKliment Yanev
2011-09-08Merge pull request #80 from alexrj/different-endstopskliment
2011-09-04Merge pull request #83 from condac/patch-1kliment
2011-09-04New and improved On and Off for FAN_PINcondac
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-22 10:43:19 +0000