| Age | Commit message (Expand) | Author |
|---|
| 2012-06-27 | use PID_PGAIN, PID_IGAIN, PID_DGAIN for PID default values | Felipe Corrêa da Silva Sanches |
| 2012-06-27 | refactor eeprom routines to make it possible to modify the value of a single ... | Felipe Corrêa da Silva Sanches |
| 2012-06-18 | reimplement homing routine as an inline function | Felipe Corrêa da Silva Sanches |
| 2012-06-18 | refactoring homing routine to avoid copy&pasted code | Felipe Corrêa da Silva Sanches |
| 2012-06-15 | fix a few typos and correct english usage | Felipe Corrêa da Silva Sanches |
| 2012-06-14 | Merge pull request #186 from blddk/experimental | midopple |
| 2012-06-14 | Forgot to pit the part in where it makes the pin an output pin... >.< | blddk |
| 2012-06-12 | Version 1.3.19T | midopple |
| 2012-06-11 | Merge pull request #183 from kliment/master | midopple |
| 2012-06-11 | Error with Command M201, when this Command is use the same Values are written... | midopple |
| 2012-06-07 | Added M400 | blddk |
| 2012-05-24 | Too many if('s | blddk |
| 2012-05-17 | Merge pull request #171 from kliment/master | midopple |
| 2012-05-16 | If a small move is drop and the next move is retract the speed is wrong calcu... | midopple |
| 2012-05-04 | Version 1.3.17T | midopple |
| 2012-05-01 | Merge pull request #168 from kliment/master | midopple |
| 2012-04-30 | Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | OhmEye |
| 2012-04-24 | Extra Retract Feedrate for Extruder | midopple |
| 2012-04-23 | Ignore ":" in comments. | midopple |
| 2012-04-22 | Version 1.3.15T | midopple |
| 2012-04-20 | When endstop is hit count virtual steps, so the print lose no position when e... | midopple |
| 2012-04-20 | - Extrudmultiply with code M221 Sxxx (S100 original Extrude value) | midopple |
| 2012-04-01 | Merge pull request #161 from se5a/master | kliment |
| 2012-04-02 | Added M93 command. sends current steps for all axis | se5a |
| 2012-03-30 | Merge pull request #160 from kliment/master | kliment |
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM
| midopple |
| 2012-03-28 | Merge from experimental, thanks to triffid_hunter | midopple |
| 2012-03-28 | fix enable_endstops being used before its definition | Michael Moon |
| 2012-03-27 | Fixed arc offset | midopple |
| 2012-03-19 | Fixes virtual endstops when using mixed physical endstop positions. | midopple |
| 2012-03-19 | Version 1.3.11T | midopple |
| 2012-03-14 | ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared
| midopple |
| 2012-03-12 | calculate feedrate without extrude before planner block is set | midopple |
| 2012-03-04 | Move SLOWDOWN Funktion up, at the current position does not work | midopple |
| 2012-02-24 | If a line starts with ';', it is ignored but comment_mode is reset. | midopple |
| 2012-02-24 | Version 1.3.07T | midopple |
| 2012-02-17 | The microcontroller can store settings to EEPROM | midopple |
| 2012-02-15 | - changed homing function to not conflict with min_software_endstops/max_soft... | midopple |
| 2012-02-05 | - Implement Plannercode from Marlin V1 --> big thanks to Erik | midopple |
| 2012-01-29 | Add function to check the UART buffer while arc function is working | midopple |
| 2012-01-29 | Update Changelog in Mainfile | midopple |
| 2012-01-29 | Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2 | midopple |
| 2012-01-29 | Change infotext | midopple |
| 2012-01-29 | New Version Sprinter V2 | midopple |
| 2012-01-22 | Reported wrong temperature while heating up | blddk |
| 2012-01-22 | Changed temperature table for bed, to the one for the bed, instead of for the... | blddk |
| 2012-01-22 | Added option to set a delay after enabeling stepper driver, to allow the driv... | blddk |
| 2011-12-06 | Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 board... | Greg Dahlman |
| 2011-12-04 | Added an option to make init.g on SD run on boot. | Nathan Zadoks |
| 2011-11-16 | M30/M31 fast sd block transfer | Philip Kin |
