| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-05-28 | Merge pull request #177 from kliment/master | midopple | |
| Wrong declaration for Variable min_time_before_dir_change | |||
| 2012-05-28 | Merge pull request #176 from blddk/experimental | midopple | |
| Error with DELAY_ENABLE Thanks to blddk | |||
| 2012-05-24 | Added variables for extruder fan | blddk | |
| 2012-05-24 | Added function to turn a fan on and off to keep heat from the hotend to rise ↵ | blddk | |
| up into the extruder. | |||
| 2012-05-24 | Too many if('s | blddk | |
| 2012-05-24 | Wrong declaration for Variable min_time_before_dir_change | midopple | |
| should be const long | |||
| 2012-05-21 | Arduino 1.0 build | Changwoo Ryu | |
| 2012-05-17 | Merge pull request #171 from kliment/master | midopple | |
| additional dropsegments test | |||
| 2012-05-16 | If a small move is drop and the next move is retract the speed is wrong ↵ | midopple | |
| calculated see https://github.com/kliment/Sprinter/issues/170 thanks to jschleic | |||
| 2012-05-15 | Add MOTHERBOARD 51 for GEN6 with Heatbed and Heatbedsensor | midopple | |
| 2012-05-04 | Version 1.3.17T | midopple | |
| - M303 - PID relay autotune possible - G4 Wait until last move is done | |||
| 2012-05-01 | Merge pull request #168 from kliment/master | midopple | |
| Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | |||
| 2012-04-30 | Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | OhmEye | |
| enabled. Fix: If SD_FAST_XFER_AKTIV is defined, fast_xfer() only declares g_heater_pwm_val if PIDTEMP is defined, but later assigns g_heater_pwm_val=0 regardless whether PIDTEMP is defined or not. If PIDTEMP is undefined, g_heater_pwm_val is undeclared at compile time and generates the appropriate error. I solved by not using g_heater_pwm_val if PIDTEMP is undefined (and therefor undeclared.) Also, the extern declaration was as an int, when g_heater_pwm_val is defined as a volatile unsigned char. This caused a duplicate declaration error, which was solved by changing the declaration in fast_xfer() to match the definition. I didn't dig deeper to try to understand if the mismatch was intentional or test operation other than verify the compile errors no longer occur. | |||
| 2012-04-24 | Fix commit Text | midopple | |
| 2012-04-24 | Extra Retract Feedrate for Extruder | midopple | |
| - Use extra extruder feedrate limit for reverse moves, and also the first forward move after a reverse | |||
| 2012-04-24 | Fix typo in Parameteroutput | midopple | |
| 2012-04-23 | Ignore ":" in comments. | midopple | |
| 2012-04-22 | Version 1.3.15T | midopple | |
| - M206 - set additional homeing offset (Thank to se5a for this idea) (First Version is without saving to EEPROM) - Option for minimum FAN start speed --> #define MINIMUM_FAN_START_SPEED 50 (set it to zero to deaktivate) | |||
| 2012-04-20 | When endstop is hit count virtual steps, so the print lose no position when ↵ | midopple | |
| endstop is hit | |||
| 2012-04-20 | - Extrudmultiply with code M221 Sxxx (S100 original Extrude value) | midopple | |
| - use Feedratefaktor only when Extruded lenght > 0 - M106 / M107 can drive the FAN with PWM + Port check for not using Timer 1 - New Option --> FAN_SOFT_PWM, with this option the FAN PWM can use every digital I/O (PWM with 500 hz) - Added M93 command. Sends current steps for all axis. | |||
| 2012-04-02 | Fixed small bug in arcs when segemnts are zero | midopple | |
| Thanks to hurzl | |||
| 2012-04-01 | Merge pull request #161 from se5a/master | kliment | |
| Added M93 command - sends current steps per unit for all axis | |||
| 2012-04-02 | Added M93 command. sends current steps for all axis | se5a | |
| 2012-03-30 | Merge pull request #160 from kliment/master | kliment | |
| Command M106 / M107 | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-28 | Merge from experimental, thanks to triffid_hunter | midopple | |
| 2012-03-28 | fix enable_endstops being used before its definition | Michael Moon | |
| 2012-03-27 | Fixed arc offset | midopple | |
| Thanks to Erik van der Zalm | |||
| 2012-03-27 | Set the defaults for the heart of the sun...uhm, set default board to 33 | Kliment Yanev | |
| 2012-03-23 | First char '#' was unicode so linux give an compile error | midopple | |
| 2012-03-19 | Fixes virtual endstops when using mixed physical endstop positions. | midopple | |
| Thanks to ticking | |||
| 2012-03-19 | Merge commit pins.h from master to experimentell | midopple | |
| Conflicts: Sprinter/pins.h | |||
| 2012-03-19 | Version 1.3.11T | midopple | |
| - fix for broken include in store_eeprom.cpp --> Thanks to kmeehl (issue #145) - Make fastio & Arduino pin numbering consistent for AT90USB128x. --> Thanks to lincomatic - Select Speedtable with F_CPU - Use same Values for Speedtables as Marlin | |||
| 2012-03-19 | fix for broken include in store_eeprom.cpp | midopple | |
| Thanks to kmeehl | |||
| 2012-03-19 | Make fastio & Arduino pin numbering consistent for AT90USB128x. | midopple | |
| Thanks to lincomatic | |||
| 2012-03-17 | Make fastio & Arduino pin numbering consistent for AT90USB128x | lincomatic | |
| 2012-03-14 | ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared | midopple | |
| New Version V1.3.10T | |||
| 2012-03-13 | Add info to GEN7 Pins | midopple | |
| 2012-03-13 | Update pins.h for gen7, working setup for 20MHz | Christian Metzen | |
| 2012-03-12 | calculate feedrate without extrude before planner block is set | midopple | |
| 2012-03-10 | New Board --> GEN7 @ 20 Mhz | midopple | |
| Select in configuration.h --> #define MOTHERBOARD 71 New Speedtable for 16 Mhz and 20 Mhz | |||
| 2012-03-04 | Merge commit 'from changwoo/arduino-1.0-compatibility' into experimental | midopple | |
| 2012-03-04 | Move SLOWDOWN Funktion up, at the current position does not work | midopple | |
| 2012-03-05 | Correct SD for Arduino 1.0 compatibility | Changwoo Ryu | |
| With Arduino 1.0 Print class: - write() should return, and - print() with a uint_8 or int_8 character argument does not call print(char) anymore. So character argument should be casted to 'char' explicitly. | |||
| 2012-02-24 | Merge commit '89180de4bfd598298f4d5e77889c57a250e35084' into experimental | midopple | |
| Conflicts: Sprinter/Makefile | |||
| 2012-02-24 | If a line starts with ';', it is ignored but comment_mode is reset. | midopple | |
| A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. --> Tanks to jschleic Same fix for SD Card, testet and work (midopple) | |||
| 2012-02-24 | Version 1.3.07T | midopple | |
| - Optimize Variable Size (faster Code) --> heater.cpp - Remove unused Code from Interrupt --> faster ~ 22 us per step - Replace abs with fabs --> Faster and smaler | |||
| 2012-02-24 | Remove unused function "st_set_position" | midopple | |
| 2012-02-24 | Add "store_eeprom.cpp" to makefile | midopple | |
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |