summaryrefslogtreecommitdiff
path: root/Tonokip_Firmware/Tonokip_Firmware.pde
AgeCommit message (Expand)Author
2011-05-15Remove M86, make kill() shut down motors and heaters, but not stop responding...kliment
2011-05-15Make temperature check interval constant regardless of whether a move is happ...kliment
2011-05-14Make either x steps or y steps remaining shortcut the loopkliment
2011-05-14Inverse the logic in the conditional that determines whether to continuekliment
2011-05-14Fix terrible lockup bug with RAMP accelerationkliment
2011-05-14Added a few spaces here and there.MrAlvin
2011-05-13Fix typo in M201/M202 y-acceleration settingKeegi
2011-05-12Removing MCode for overheat protectionNils
2011-05-12Merge branch 'master' of github.com:kliment/SprinterNils
2011-05-12Adding experimental support for max temperature gueard (M143)Nils
2011-05-12Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-12Merge pull request #15 from sam-ward/masterkliment
2011-05-12Make heater check more frequent during moves, intialize SD faster to avoid co...kliment
2011-05-12Added G28 command description to top of file.Sam Ward
2011-05-12Fixed prepare_move function prototype and inliningSam Ward
2011-05-11Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-11Remove extraneous newlinekliment
2011-05-11Added some more intelligent homing logicSam Ward
2011-05-11Added G28 homing code.Sam Ward
2011-05-11Cleaning up code formattingSam Ward
2011-05-11Moved function definitions into separate .h file for readability.Sam Ward
2011-05-11Merge branch 'master' of https://github.com/kliment/SprinterSam Ward
2011-05-11extra CRLFSam Ward
2011-05-11Added M201 and M202 to set max acceleration for respectively print and travel...Emanuele Caruso
2011-05-11Dramatically decreased GCODE write time to SDEmanuele Caruso
2011-05-07Added M84 Timeout for steppers:Christopher Keller
2011-05-04Fixed deceleration bug for constant accelerationEmanuele Caruso
2011-05-04Added constant acceleration option (aka speed ramp), enabled by defaultEmanuele Caruso
2011-05-04Added max z feedrate configuration value, default to 120 mm/min. Solution sug...Emanuele Caruso
2011-05-04Made exponential acceleration optional with a #define in configuration.hEmanuele Caruso
2011-05-03Make sure M190 does nothing if no heated bed present. Fix report format to ma...kliment
2011-05-03Added support for M190 - Wait for heated bed to reach target temp.Sam Ward
2011-05-03Merge pull request #4 from ScribbleJ/master.kliment
2011-05-02Merge pull request #6 from kludgineer/master.kliment
2011-05-02Edited Tonokip_Firmware/Tonokip_Firmware.pde via GitHubkludgineer
2011-05-03Added comments for M28, M29 to list of implemented GcodesSam Ward
2011-05-03Added Makefile and declared required functions in .pde to support it working.Christopher Jansen
2011-05-02Merge remote branch 'origin/master'Emanuele Caruso
2011-05-01Added watchdog aand minimal temp for greater safety in the case of a disconne...kliment
2011-05-01Added configuration value for absolute delay microseconds, default to 1. This...Emanuele Caruso
2011-05-01Added configuration parameter for delaying steps, STEP_DELAY_RATIO.Emanuele Caruso
2011-04-30Adding Support for SanguinololuTommy Cheng
2011-04-29Adding basic capabilities (M115) implementationNils
2011-04-28Fix missing { causing compile errorkliment
2011-04-27Merge branch 'master' of git@github.com:kliment/Klimentkipkliment
2011-04-27Added PWM control to fan pin, added smoothing code for erratic gen6 temp read...kliment
2011-04-25Added separate acceleration configuration parameter for travel movesEmanuele Caruso
2011-04-22Merge branch 'minconstspeed'Emanuele Caruso
2011-04-22Added min constant speed units configuration value for acceleration. Disabled...Emanuele Caruso
2011-04-22Do not include max6675 functions if they are not in usekliment
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-22 23:58:34 +0000