diff options
Diffstat (limited to 'ospf6d/OSPFv3-MIB.txt')
| -rw-r--r-- | ospf6d/OSPFv3-MIB.txt | 6709 |
1 files changed, 3951 insertions, 2758 deletions
diff --git a/ospf6d/OSPFv3-MIB.txt b/ospf6d/OSPFv3-MIB.txt index 80e6cb2d..258f533e 100644 --- a/ospf6d/OSPFv3-MIB.txt +++ b/ospf6d/OSPFv3-MIB.txt @@ -1,2758 +1,3951 @@ -OSPFV3-MIB DEFINITIONS ::= BEGIN - -IMPORTS - MODULE-IDENTITY, OBJECT-TYPE, mib-2, experimental, - Counter32, Gauge32, Integer32, IpAddress, - Unsigned32 - FROM SNMPv2-SMI - TEXTUAL-CONVENTION, TruthValue, StorageType, RowStatus - FROM SNMPv2-TC - MODULE-COMPLIANCE, OBJECT-GROUP - FROM SNMPv2-CONF - InterfaceIndex - FROM IF-MIB - InetAddressType, InetAddress, InetAddressPrefixLength - FROM INET-ADDRESS-MIB - AreaID, RouterID, Metric, BigMetric, Status, - HelloRange, DesignatedRouterPriority - FROM OSPF-MIB; - -ospfv3MIB MODULE-IDENTITY - LAST-UPDATED "200404081200Z" - ORGANIZATION "IETF OSPF Working Group" - CONTACT-INFO - "WG E-Mail: ospf@peach.ease.lsoft.com - WG Chairs: John.Moy@sycamorenet.com - acee@redback.com - rohit@xebeo.com - - Dan Joyal - Nortel Networks - 600 Technology Park Drive - Billerica, MA 01821, USA - djoyal@nortelnetworks.com - - Vishwas Manral - SiNett Corporation - 2/1, First Floor - Embassy Icon Annex - Infantry Road - Bangalore 560001 - vishwas@sinett.com" - - DESCRIPTION - "The MIB module to describe OSPF version 3" - REVISION "200404081200Z" - DESCRIPTION -- RFC Editor assigns RFC xxxx - "Initial version, published as RFC xxxx" - ::= { experimental 102 } -- IANA assigns xx - --- Texual conventions - -UpToRefreshInterval ::= TEXTUAL-CONVENTION - STATUS current - DESCRIPTION - "The values one might be able to configure for - variables bounded by the Refresh Interval" - SYNTAX Integer32 (1..1800) - -RouterDeadRange ::= TEXTUAL-CONVENTION - STATUS current - DESCRIPTION - "The range of intervals in seconds that a routers hello - must have not been seen before a neighbor declares the - router down" - SYNTAX Integer32 (1..'FFFF'h) - - --- Top-level structure of MIB -ospfv3Objects OBJECT IDENTIFIER ::= { ospfv3MIB 1 } -ospfv3Conformance OBJECT IDENTIFIER ::= { ospfv3MIB 2 } - --- OSPFv3 General Variables - --- These parameters apply globally to the Router's --- OSPFv3 Process. - -ospfv3GeneralGroup OBJECT IDENTIFIER ::= { ospfv3Objects 1 } - -ospfv3RouterId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "A 32-bit integer uniquely identifying the - router in the Autonomous System. - To ensure uniqueness, this may - default to the value of one of the - router's IPv4 interface addresses if IPv4 is - configured on the router." - ::= { ospfv3GeneralGroup 1 } - -ospfv3AdminStat OBJECT-TYPE - SYNTAX Status - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The administrative status of OSPFv3 in the - router. The value 'enabled' denotes that the - OSPFv3 Process is active on at least one inter- - face; 'disabled' disables it on all inter- - faces." - ::= { ospfv3GeneralGroup 2 } - -ospfv3VersionNumber OBJECT-TYPE - SYNTAX INTEGER { version3(3) } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The version number of OSPF for IPv6 is 3." - ::= { ospfv3GeneralGroup 3 } - -ospfv3AreaBdrRtrStatus OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A flag to note whether this router is an area - border router." - REFERENCE - "OSPF Version 2, Section 3 Splitting the AS into - Areas" - ::= { ospfv3GeneralGroup 4 } - -ospfv3ASBdrRtrStatus OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "A flag to note whether this router is config- - ured as an Autonomous System border router." - REFERENCE - "OSPF Version 2, Section 3.3 Classification of - routers" - ::= { ospfv3GeneralGroup 5 } - -ospfv3AsScopeLsaCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of AS-Scope (e.g. AS-External) link-state - advertisements in the link-state database." - ::= { ospfv3GeneralGroup 6 } - -ospfv3AsScopeLsaCksumSum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32-bit unsigned sum of the LS checksums of - the AS-scoped link-state advertisements con- - tained in the link-state database. This sum - can be used to determine if there has been a - change in a router's link state database, and - to compare the link-state database of two - routers." - ::= { ospfv3GeneralGroup 7 } - -ospfv3OriginateNewLsas OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of new link-state advertisements - that have been originated. This number is in- - cremented each time the router originates a new - LSA." - ::= { ospfv3GeneralGroup 8 } - -ospfv3RxNewLsas OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of link-state advertisements re- - ceived determined to be new instantiations. - This number does not include newer instantia- - tions of self-originated link-state advertise- - ments." - ::= { ospfv3GeneralGroup 9 } - -ospfv3ExtLsaCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of External(LS type 0x4005) in the link- - state database" - ::= { ospfv3GeneralGroup 10 } - - -ospfv3ExtAreaLsdbLimit OBJECT-TYPE - SYNTAX Integer32 (-1..'7FFFFFFF'h) - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The maximum number of non-default AS- - external-LSAs entries that can be stored in the - link-state database. If the value is -1, then - there is no limit. - - When the number of non-default AS-external-LSAs - in a router's link-state database reaches - ospfv3ExtAreaLsdbLimit, the router enters Overflow- - State. The router never holds more than - ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs - in its database. OspfExtAreaLsdbLimit MUST be set - identically in all routers attached to the OSPFv3 - backbone and/or any regular OSPFv3 area. (i.e., - OSPFv3 stub areas and NSSAs are excluded)." - ::= { ospfv3GeneralGroup 11 } - -ospfv3MulticastExtensions OBJECT-TYPE - SYNTAX BITS { - intraAreaMulticast(0), - interAreaMulticast(1), - interAsMulticast(2) - } - - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "A Bit Mask indicating whether the router is - forwarding IPv6 multicast datagrams - based on the algorithms defined in the Multi- - cast Extensions to OSPF. - - If intraAreaMulticast set, indicates that the router - can forward IPv6 multicast datagrams in the router's - directly attached areas (called intra-area mul- - ticast routing). - - If interAreaMulticast set, indicates that the router - can forward IPv6 multicast datagrams between OSPFv3 - areas (called inter-area multicast routing). - - If interAsMulticast set, indicates that the router can - forward IPv6 multicast datagrams between Auto- - nomous Systems (called inter-AS multicast rout- - ing). - - Only certain combinations of bit settings are - allowed, namely: - - All bits cleared (no multicasting) - - intraAreaMulticast only, - - intraAreaMulticast and interAreaMulticast, - - intraAreaMulticast and interAsMulticast - - intraAreaMulticast, interAreaMulticast and - interAsMulticast - By default, all bits are cleared." - ::= { ospfv3GeneralGroup 12 } - -ospfv3ExitOverflowInterval OBJECT-TYPE - SYNTAX Unsigned32 - UNITS "seconds" - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The number of seconds that, after entering - OverflowState, a router will attempt to leave - OverflowState. This allows the router to again - originate non-default AS-External-LSAs. When - set to 0, the router will not leave Overflow- - State until restarted." - ::= { ospfv3GeneralGroup 13 } - -ospfv3DemandExtensions OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The router's support for demand routing." - REFERENCE - "OSPF Version 2, Appendix on Demand Routing" - ::= { ospfv3GeneralGroup 14 } - -ospfv3TrafficEngineeringSupport OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The router's support for traffic engineering - extensions." - ::= { ospfv3GeneralGroup 15 } - -ospfv3ReferenceBandwidth OBJECT-TYPE - SYNTAX Unsigned32 - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "Reference bandwidth in kilobits/second for - calculating default interface metrics. The - default value is 100,000 KBPS (100 MBPS)" - ::= { ospfv3GeneralGroup 16 } - -ospfv3RestartSupport OBJECT-TYPE - SYNTAX INTEGER { none (1), - plannedOnly (2), - plannedAndUnplanned (3) - } - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "The router's support for OSPF hitless restart. - Options include: no restart support, only planned - restarts or both planned and unplanned restarts." - ::= { ospfv3GeneralGroup 17 } - -ospfv3RestartInterval OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-write - STATUS current - DESCRIPTION - "Configured OSPF hitless restart timeout interval." - ::= { ospfv3GeneralGroup 18 } - -ospfv3RestartStatus OBJECT-TYPE - SYNTAX INTEGER { notRestarting (1), - plannedRestart (2), - unplannedRestart (3) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Current status of OSPF hitless restart." - ::= { ospfv3GeneralGroup 19 } - -ospfv3RestartAge OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Remaining time in current OSPF hitless restart - interval." - ::= { ospfv3GeneralGroup 20 } - -ospfv3RestartExitReason OBJECT-TYPE - SYNTAX INTEGER { none (1), -- none attempted - inProgress (2), -- restart in - -- progress - completed (3), -- successfully - -- completed - timedOut (4), -- timed out - topologyChanged (5) -- aborted due to - -- topologychange. - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Describes the outcome of the last attempt at a - hitless restart. If the value is 'none', no restart - has yet been attempted. If the value is 'inProgress', - a restart attempt is currently underway." - ::= { ospfv3GeneralGroup 21 } - - --- The OSPFv3 Area Data Structure contains information --- regarding the various areas. The interfaces and --- virtual links are configured as part of these areas. --- Area 0.0.0.0, by definition, is the Backbone Area - -ospfv3AreaTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3AreaEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "Information describing the configured parame- - ters and cumulative statistics of the router's - attached areas." - REFERENCE - "OSPF Version 2, Section 6 The Area Data Struc- - ture" - ::= { ospfv3Objects 2 } - -ospfv3AreaEntry OBJECT-TYPE - SYNTAX Ospfv3AreaEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "Information describing the configured parame- - ters and cumulative statistics of one of the - router's attached areas." - INDEX { ospfv3AreaId } - ::= { ospfv3AreaTable 1 } - -Ospfv3AreaEntry ::= SEQUENCE { - ospfv3AreaId - AreaID, - ospfv3ImportAsExtern - INTEGER, - ospfv3AreaSpfRuns - Counter32, - ospfv3AreaBdrRtrCount - Gauge32, - ospfv3AreaAsBdrRtrCount - Gauge32, - ospfv3AreaScopeLsaCount - Gauge32, - ospfv3AreaScopeLsaCksumSum - Integer32, - ospfv3AreaSummary - INTEGER, - ospfv3AreaStatus - RowStatus, - ospfv3StubMetric - BigMetric, - ospfv3AreaNssaTranslatorRole - INTEGER, - ospfv3AreaNssaTranslatorState - INTEGER, - ospfv3AreaNssaTranslatorStabilityInterval - Unsigned32, - ospfv3AreaNssaTranslatorEvents - Counter32, - ospfv3AreaStubMetricType - INTEGER - } - -ospfv3AreaId OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A 32-bit integer uniquely identifying an area. - Area ID 0.0.0.0 is used for the OSPFv3 backbone." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3AreaEntry 1 } - -ospfv3ImportAsExtern OBJECT-TYPE - SYNTAX INTEGER { - importExternal(1), -- normal area - importNoExternal(2), -- stub area - importNssa(3) -- not-so-stubby-area - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Indicates whether an area is a Stub area, NSSA, or - standard area. AS-scope LSAs are not imported into Stub - Areas or NSSAs. NSSAs import AS-External data as Type-7 - LSAs which have Area-scope" - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - DEFVAL { importExternal } - ::= { ospfv3AreaEntry 2 } - -ospfv3AreaSpfRuns OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of times that the intra-area route - table has been calculated using this area's - link-state database. This is typically done - using Dijkstra's algorithm." - ::= { ospfv3AreaEntry 3 } - -ospfv3AreaBdrRtrCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The total number of area border routers reach- - able within this area. This is initially zero, - and is calculated in each SPF Pass." - ::= { ospfv3AreaEntry 4 } - -ospfv3AreaAsBdrRtrCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The total number of Autonomous System border - routers reachable within this area. This is - initially zero, and is calculated in each SPF - Pass." - ::= { ospfv3AreaEntry 5 } - -ospfv3AreaScopeLsaCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The total number of Area-Scope link-state - advertisements in this area's link-state - database." - ::= { ospfv3AreaEntry 6 } - -ospfv3AreaScopeLsaCksumSum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32-bit unsigned sum of the Area-Scope link-state - advertisements' LS checksums contained in this - area's link-state database. The sum can be used - to determine if there has been a change in a - router's link state database, and to compare the - link-state database of two routers." - ::= { ospfv3AreaEntry 7 } - -ospfv3AreaSummary OBJECT-TYPE - SYNTAX INTEGER { - noAreaSummary(1), - sendAreaSummary(2) - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The variable ospfv3AreaSummary controls the im- - port of Inter-Area LSAs into stub areas. It has - no effect on other areas. - - If it is noAreaSummary, the router will neither - originate nor propagate Inter-Area LSAs into the - stub area. It will rely entirely on its de- - fault route. - - If it is sendAreaSummary, the router will both - summarize and propagate Inter-Area LSAs." - DEFVAL { sendAreaSummary } - ::= { ospfv3AreaEntry 8 } - -ospfv3AreaStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail - in [6]." - ::= { ospfv3AreaEntry 9 } - -ospfv3StubMetric OBJECT-TYPE - SYNTAX BigMetric - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The metric value advertised for the default route - into Stub and NSSA areas." - ::= { ospfv3AreaEntry 10 } - -ospfv3AreaNssaTranslatorRole OBJECT-TYPE - SYNTAX INTEGER { always(1), candidate(2) } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Indicates an NSSA Border router's ability to - perform NSSA translation of type-7 LSAs into - type-5 LSAs." - DEFVAL { candidate } - ::= { ospfv3AreaEntry 11 } - -ospfv3AreaNssaTranslatorState OBJECT-TYPE - SYNTAX INTEGER { - enabled(1), - elected(2), - disabled(3) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates if and how an NSSA Border router is - performing NSSA translation of type-7 LSAs into type-5 - LSAs. When this object is set to enabled, the NSSA - Border router's ospfv3AreaNssTranslatorRole - has been set to always. When this object is set to - elected, a candidate NSSA Border router is translating - type-7 LSAs into type-5. When this object is set to - disabled, a candidate NSSA Border router is NOT - translating type-7 LSAs into type-5." - ::= { ospfv3AreaEntry 12 } - -ospfv3AreaNssaTranslatorStabilityInterval OBJECT-TYPE - SYNTAX Unsigned32 - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The number of seconds after an elected translator - determines its services are no longer required, that - it should continue to perform its translation duties." - DEFVAL { 40 } - ::= { ospfv3AreaEntry 13 } - -ospfv3AreaNssaTranslatorEvents OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates the number of Translator State changes - that have occurred since the last boot-up." - ::= { ospfv3AreaEntry 14 } - -ospfv3AreaStubMetricType OBJECT-TYPE - SYNTAX INTEGER { - ospfv3Metric (1), -- OSPF Metric - comparableCost (2), -- external type 1 - nonComparable (3) -- external type 2 - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable displays the type of metric ad- - vertised as a default route." - DEFVAL { ospfv3Metric } - ::= { ospfv3AreaEntry 15 } - --- OSPFv3 AS-Scope Link State Database - --- The Link State Database contains the AS-Scope Link State --- Advertisements from throughout the areas that the --- device is attached to. - -ospfv3AsLsdbTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3AsLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The OSPFv3 Process's AS-Scope Link State Database." - ::= { ospfv3Objects 3 } - -ospfv3AsLsdbEntry OBJECT-TYPE - SYNTAX Ospfv3AsLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A single AS-Scope Link State Advertisement." - INDEX { ospfv3AsLsdbType, - ospfv3AsLsdbRouterId, - ospfv3AsLsdbLsid } - ::= { ospfv3AsLsdbTable 1 } - -Ospfv3AsLsdbEntry ::= SEQUENCE { - ospfv3AsLsdbType - Unsigned32, - ospfv3AsLsdbRouterId - RouterID, - ospfv3AsLsdbLsid - IpAddress, - ospfv3AsLsdbSequence - Integer32, - ospfv3AsLsdbAge - Integer32, - ospfv3AsLsdbChecksum - Integer32, - ospfv3AsLsdbAdvertisement - OCTET STRING, - ospfv3AsLsdbTypeKnown - TruthValue - } - -ospfv3AsLsdbType OBJECT-TYPE - SYNTAX Unsigned32 (0..4294967295) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The type of the link state advertisement. - Each link state type has a separate advertise- - ment format. AS-Scope LSAs not recognized by - the router may be stored in the database." - ::= { ospfv3AsLsdbEntry 1 } - -ospfv3AsLsdbRouterId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32 bit number that uniquely identifies the - originating router in the Autonomous System." - REFERENCE - "OSPF Version 2, Appendix C.1 Global parameters" - ::= { ospfv3AsLsdbEntry 2 } - -ospfv3AsLsdbLsid OBJECT-TYPE - SYNTAX IpAddress - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Link State ID is an LS Type Specific field - containing a unique identifier; - it identifies the piece of the routing domain - that is being described by the advertisement. - In contrast to OSPFv2, the LSID has no - addressing semantics." - ::= { ospfv3AsLsdbEntry 3 } - --- Note that the OSPF Sequence Number is a 32 bit signed --- integer. It starts with the value '80000001'h, --- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h --- Thus, a typical sequence number will be very negative. - -ospfv3AsLsdbSequence OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The sequence number field is a signed 32-bit - integer. It is used to detect old and dupli- - cate link state advertisements. The space of - sequence numbers is linearly ordered. The - larger the sequence number the more recent the - advertisement." - REFERENCE - "OSPF Version 2, Section 12.1.6 LS sequence - number" - ::= { ospfv3AsLsdbEntry 4 } - -ospfv3AsLsdbAge OBJECT-TYPE - SYNTAX Integer32 -- Should be 0..MaxAge - -- unless DoNotAge bit is set - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the age of the link state adver- - tisement in seconds." - REFERENCE - "OSPF Version 2, Section 12.1.1 LS age" - ::= { ospfv3AsLsdbEntry 5 } - -ospfv3AsLsdbChecksum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the checksum of the complete - contents of the advertisement, excepting the - age field. The age field is excepted so that - an advertisement's age can be incremented - without updating the checksum. The checksum - used is the same that is used for ISO connec- - tionless datagrams; it is commonly referred to - as the Fletcher checksum." - REFERENCE - "OSPF Version 2, Section 12.1.7 LS checksum" - ::= { ospfv3AsLsdbEntry 6 } - -ospfv3AsLsdbAdvertisement OBJECT-TYPE - SYNTAX OCTET STRING (SIZE (1..65535)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The entire Link State Advertisement, including - its header." - ::= { ospfv3AsLsdbEntry 7 } - -ospfv3AsLsdbTypeKnown OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Is the LSA type recognized by this Router?" - ::= { ospfv3AsLsdbEntry 8 } - - --- OSPFv3 Area-Scope Link State Database - --- The Link State Database contains the Area-Scope Link State --- Advertisements from throughout the area that the --- device is attached to. - -ospfv3AreaLsdbTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3AreaLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The OSPFv3 Process's Area-Scope Link State Database." - ::= { ospfv3Objects 4 } - -ospfv3AreaLsdbEntry OBJECT-TYPE - SYNTAX Ospfv3AreaLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A single Area-Scope Link State Advertisement." - INDEX { ospfv3AreaLsdbAreaId, - ospfv3AreaLsdbType, - ospfv3AreaLsdbRouterId, - ospfv3AreaLsdbLsid } - ::= { ospfv3AreaLsdbTable 1 } - -Ospfv3AreaLsdbEntry ::= SEQUENCE { - ospfv3AreaLsdbAreaId - AreaID, - ospfv3AreaLsdbType - Unsigned32, - ospfv3AreaLsdbRouterId - RouterID, - ospfv3AreaLsdbLsid - IpAddress, - ospfv3AreaLsdbSequence - Integer32, - ospfv3AreaLsdbAge - Integer32, - ospfv3AreaLsdbChecksum - Integer32, - ospfv3AreaLsdbAdvertisement - OCTET STRING, - ospfv3AreaLsdbTypeKnown - TruthValue - } - -ospfv3AreaLsdbAreaId OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32 bit identifier of the Area from which the - LSA was received." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3AreaLsdbEntry 1 } - -ospfv3AreaLsdbType OBJECT-TYPE - SYNTAX Unsigned32 (0..4294967295) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The type of the link state advertisement. - Each link state type has a separate advertise- - ment format. Area-Scope LSAs unrecognized by the - router are also stored in this database." - ::= { ospfv3AreaLsdbEntry 2 } - -ospfv3AreaLsdbRouterId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32 bit number that uniquely identifies the - originating router in the Autonomous System." - REFERENCE - "OSPF Version 2, Appendix C.1 Global parameters" - ::= { ospfv3AreaLsdbEntry 3 } - -ospfv3AreaLsdbLsid OBJECT-TYPE - SYNTAX IpAddress - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Link State ID is an LS Type Specific field - containing a unique identifier; - it identifies the piece of the routing domain - that is being described by the advertisement. - In contrast to OSPFv2, the LSID has no - addressing semantics." - ::= { ospfv3AreaLsdbEntry 4 } - --- Note that the OSPF Sequence Number is a 32 bit signed --- integer. It starts with the value '80000001'h, --- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h --- Thus, a typical sequence number will be very negative. - -ospfv3AreaLsdbSequence OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The sequence number field is a signed 32-bit - integer. It is used to detect old and dupli- - cate link state advertisements. The space of - sequence numbers is linearly ordered. The - larger the sequence number the more recent the - advertisement." - REFERENCE - "OSPF Version 2, Section 12.1.6 LS sequence - number" - ::= { ospfv3AreaLsdbEntry 5 } - -ospfv3AreaLsdbAge OBJECT-TYPE - SYNTAX Integer32 -- Should be 0..MaxAge - -- unless DoNotAge bit is set - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the age of the link state adver- - tisement in seconds." - REFERENCE - "OSPF Version 2, Section 12.1.1 LS age" - ::= { ospfv3AreaLsdbEntry 6 } - -ospfv3AreaLsdbChecksum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the checksum of the complete - contents of the advertisement, excepting the - age field. The age field is excepted so that - an advertisement's age can be incremented - without updating the checksum. The checksum - used is the same that is used for ISO connec- - tionless datagrams; it is commonly referred to - as the Fletcher checksum." - REFERENCE - "OSPF Version 2, Section 12.1.7 LS checksum" - ::= { ospfv3AreaLsdbEntry 7 } - -ospfv3AreaLsdbAdvertisement OBJECT-TYPE - SYNTAX OCTET STRING (SIZE (1..65535)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The entire Link State Advertisement, including - its header." - ::= { ospfv3AreaLsdbEntry 8 } - -ospfv3AreaLsdbTypeKnown OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Is the LSA type recognized by this Router?" - ::= { ospfv3AreaLsdbEntry 9 } - --- OSPFv3 Link-Scope Link State Database - --- The Link State Database contains the Link-Scope Link State --- Advertisements from the links that the --- device is attached to. - -ospfv3LinkLsdbTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3LinkLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The OSPFv3 Process's Link-Scope Link State Database." - ::= { ospfv3Objects 5 } - -ospfv3LinkLsdbEntry OBJECT-TYPE - SYNTAX Ospfv3LinkLsdbEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A single Link-Scope Link State Advertisement." - INDEX { ospfv3LinkLsdbIfIndex, - ospfv3LinkLsdbType, - ospfv3LinkLsdbRouterId, - ospfv3LinkLsdbLsid } - ::= { ospfv3LinkLsdbTable 1 } - -Ospfv3LinkLsdbEntry ::= SEQUENCE { - ospfv3LinkLsdbIfIndex - InterfaceIndex, - ospfv3LinkLsdbType - Unsigned32, - ospfv3LinkLsdbRouterId - RouterID, - ospfv3LinkLsdbLsid - IpAddress, - ospfv3LinkLsdbSequence - Integer32, - ospfv3LinkLsdbAge - Integer32, - ospfv3LinkLsdbChecksum - Integer32, - ospfv3LinkLsdbAdvertisement - OCTET STRING, - ospfv3LinkLsdbTypeKnown - TruthValue - } - -ospfv3LinkLsdbIfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The identifier of the link from which the LSA - was received." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3LinkLsdbEntry 1 } - -ospfv3LinkLsdbType OBJECT-TYPE - SYNTAX Unsigned32 (0..4294967295) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The type of the link state advertisement. - Each link state type has a separate advertise- - ment format. Link-Scope LSAs unrecognized by the - router are also stored in this database." - ::= { ospfv3LinkLsdbEntry 2 } - -ospfv3LinkLsdbRouterId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32 bit number that uniquely identifies the - originating router in the Autonomous System." - REFERENCE - "OSPF Version 2, Appendix C.1 Global parameters" - ::= { ospfv3LinkLsdbEntry 3 } - -ospfv3LinkLsdbLsid OBJECT-TYPE - SYNTAX IpAddress - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Link State ID is an LS Type Specific field - containing a unique identifier; - it identifies the piece of the routing domain - that is being described by the advertisement. - In contrast to OSPFv2, the LSID has no - addressing semantics." - ::= { ospfv3LinkLsdbEntry 4 } - --- Note that the OSPF Sequence Number is a 32 bit signed --- integer. It starts with the value '80000001'h, --- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h --- Thus, a typical sequence number will be very negative. - -ospfv3LinkLsdbSequence OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The sequence number field is a signed 32-bit - integer. It is used to detect old and dupli- - cate link state advertisements. The space of - sequence numbers is linearly ordered. The - larger the sequence number the more recent the - advertisement." - REFERENCE - "OSPF Version 2, Section 12.1.6 LS sequence - number" - ::= { ospfv3LinkLsdbEntry 5 } - -ospfv3LinkLsdbAge OBJECT-TYPE - SYNTAX Integer32 -- Should be 0..MaxAge - -- unless DoNotAge bit is set - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the age of the link state - advertisement in seconds." - REFERENCE - "OSPF Version 2, Section 12.1.1 LS age" - ::= { ospfv3LinkLsdbEntry 6 } - -ospfv3LinkLsdbChecksum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "This field is the checksum of the complete - contents of the advertisement, excepting the - age field. The age field is excepted so that - an advertisement's age can be incremented - without updating the checksum. The checksum - used is the same that is used for ISO connec- - tionless datagrams; it is commonly referred to - as the Fletcher checksum." - REFERENCE - "OSPF Version 2, Section 12.1.7 LS checksum" - ::= { ospfv3LinkLsdbEntry 7 } - -ospfv3LinkLsdbAdvertisement OBJECT-TYPE - SYNTAX OCTET STRING (SIZE (1..65535)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The entire Link State Advertisement, including - its header." - ::= { ospfv3LinkLsdbEntry 8 } - -ospfv3LinkLsdbTypeKnown OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates whether the LSA type is recognized by this - Router." - ::= { ospfv3LinkLsdbEntry 9 } - - --- OSPF Host Table - --- The Host/Metric Table indicates what hosts are directly --- attached to the Router, and what metrics and types of --- service should be advertised for them. - -ospfv3HostTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3HostEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The list of Hosts, and their metrics, that the - router will advertise as host routes." - REFERENCE - "OSPF Version 2, Appendix C.6 Host route param- - eters" - ::= { ospfv3Objects 6 } - -ospfv3HostEntry OBJECT-TYPE - SYNTAX Ospfv3HostEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A metric to be advertised when a given host is - reachable." - INDEX { ospfv3HostAddressType, - ospfv3HostAddress } - ::= { ospfv3HostTable 1 } - -Ospfv3HostEntry ::= SEQUENCE { - ospfv3HostAddressType - InetAddressType, - ospfv3HostAddress - InetAddress, - ospfv3HostMetric - Metric, - ospfv3HostStatus - RowStatus, - ospfv3HostAreaID - AreaID - } - -ospfv3HostAddressType OBJECT-TYPE - SYNTAX InetAddressType - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The address type of ospfv3HostAddress. Only IPv6 - addresses without zone index are expected." - REFERENCE - "OSPF Version 2, Appendix C.6 Host route parame- - ters" - ::= { ospfv3HostEntry 1 } - - -ospfv3HostAddress OBJECT-TYPE - SYNTAX InetAddress (SIZE (16)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The IPv6 Address of the Host. Must be a Global - or Site-local address." - REFERENCE - "OSPF Version 2, Appendix C.6 Host route parame- - ters" - ::= { ospfv3HostEntry 2 } - -ospfv3HostMetric OBJECT-TYPE - SYNTAX Metric - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The Metric to be advertised." - REFERENCE - "OSPF Version 2, Appendix C.6 Host route parame- - ters" - ::= { ospfv3HostEntry 3 } - -ospfv3HostStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail - in [6]." - ::= { ospfv3HostEntry 4 } - -ospfv3HostAreaID OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The Area the Host Entry is to be found within. - By default, the area that a subsuming OSPFv3 in- - terface is in, or 0.0.0.0" - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3HostEntry 5 } - --- OSPFv3 Interface Table - -ospfv3IfTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3IfEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The OSPFv3 Interface Table describes the inter- - faces from the viewpoint of OSPFv3." - REFERENCE - "OSPF Version 2, Appendix C.3 Router interface - parameters" - ::= { ospfv3Objects 7 } - -ospfv3IfEntry OBJECT-TYPE - SYNTAX Ospfv3IfEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The OSPFv3 Interface Entry describes one inter- - face from the viewpoint of OSPFv3." - INDEX { ospfv3IfIndex } - ::= { ospfv3IfTable 1 } - - -Ospfv3IfEntry ::= SEQUENCE { - ospfv3IfIndex - InterfaceIndex, - ospfv3IfAreaId - AreaID, - ospfv3IfType - INTEGER, - ospfv3IfAdminStat - Status, - ospfv3IfRtrPriority - DesignatedRouterPriority, - ospfv3IfTransitDelay - UpToRefreshInterval, - ospfv3IfRetransInterval - UpToRefreshInterval, - ospfv3IfHelloInterval - HelloRange, - ospfv3IfRtrDeadInterval - RouterDeadRange, - ospfv3IfPollInterval - Unsigned32, - ospfv3IfState - INTEGER, - ospfv3IfDesignatedRouter - RouterID, - ospfv3IfBackupDesignatedRouter - RouterID, - ospfv3IfEvents - Counter32, - ospfv3IfStatus - RowStatus, - ospfv3IfMulticastForwarding - INTEGER, - ospfv3IfDemand - TruthValue, - ospfv3IfMetricValue - Metric, - ospfv3IfLinkScopeLsaCount - Gauge32, - ospfv3IfLinkLsaCksumSum - Integer32, - ospfv3IfInstId - Integer32, - ospfv3IfDemandNbrProbe - TruthValue, - ospfv3IfDemandNbrProbeRetxLimit - Unsigned32, - ospfv3IfDemandNbrProbeInterval - Unsigned32 - } - -ospfv3IfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The interface index of this OSPFv3 interface. - It corresponds to the interface index of the - IPv6 interface on which OSPFv3 is configured." - ::= { ospfv3IfEntry 1 } - -ospfv3IfAreaId OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "A 32-bit integer uniquely identifying the area - to which the interface connects. Area ID - 0.0.0.0 is used for the OSPFv3 backbone." - DEFVAL { '00000000'H } -- 0.0.0.0 - ::= { ospfv3IfEntry 2 } - -ospfv3IfType OBJECT-TYPE - SYNTAX INTEGER { - broadcast(1), - nbma(2), - pointToPoint(3), - pointToMultipoint(5) - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The OSPFv3 interface type." - ::= { ospfv3IfEntry 3 } - -ospfv3IfAdminStat OBJECT-TYPE - SYNTAX Status - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The OSPFv3 interface's administrative status. - The value formed on the interface, and the in- - terface will be advertised as an internal route - to some area. The value 'disabled' denotes - that the interface is external to OSPFv3." - DEFVAL { enabled } - ::= { ospfv3IfEntry 4 } - -ospfv3IfRtrPriority OBJECT-TYPE - SYNTAX DesignatedRouterPriority - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The priority of this interface. Used in - multi-access networks, this field is used in - the designated router election algorithm. The - value 0 signifies that the router is not eligi- - ble to become the designated router on this - particular network. In the event of a tie in - this value, routers will use their Router ID as - a tie breaker." - DEFVAL { 1 } - ::= { ospfv3IfEntry 5 } - -ospfv3IfTransitDelay OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The estimated number of seconds it takes to - transmit a link state update packet over this - interface." - DEFVAL { 1 } - ::= { ospfv3IfEntry 6 } - -ospfv3IfRetransInterval OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The number of seconds between link-state ad- - vertisement retransmissions, for adjacencies - belonging to this interface. This value is - also used when retransmitting database descrip- - tion and link-state request packets." - DEFVAL { 5 } - ::= { ospfv3IfEntry 7 } - -ospfv3IfHelloInterval OBJECT-TYPE - SYNTAX HelloRange - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The length of time, in seconds, between the - Hello packets that the router sends on the in- - terface. This value must be the same for all - routers attached to a common network." - DEFVAL { 10 } - ::= { ospfv3IfEntry 8 } - -ospfv3IfRtrDeadInterval OBJECT-TYPE - SYNTAX RouterDeadRange - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The number of seconds that a router's Hello - packets have not been seen before it's neigh- - bors declare the router down. This should be - some multiple of the Hello interval. This - value must be the same for all routers attached - to a common network." - DEFVAL { 40 } - ::= { ospfv3IfEntry 9 } - -ospfv3IfPollInterval OBJECT-TYPE - SYNTAX Unsigned32 - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The larger time interval, in seconds, between - the Hello packets sent to an inactive non- - broadcast multi- access neighbor." - DEFVAL { 120 } - ::= { ospfv3IfEntry 10 } - -ospfv3IfState OBJECT-TYPE - SYNTAX INTEGER { - down(1), - loopback(2), - waiting(3), - pointToPoint(4), - designatedRouter(5), - backupDesignatedRouter(6), - otherDesignatedRouter(7) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The OSPFv3 Interface State." - ::= { ospfv3IfEntry 11 } - -ospfv3IfDesignatedRouter OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Router ID of the Designated Router." - ::= { ospfv3IfEntry 12 } - -ospfv3IfBackupDesignatedRouter OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Router ID of the Backup Designated - Router." - ::= { ospfv3IfEntry 14 } - -ospfv3IfEvents OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of times this OSPF interface has - changed its state, or an error has occurred." - ::= { ospfv3IfEntry 15 } - - ospfv3IfStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail in - [6]." - ::= { ospfv3IfEntry 17 } - -ospfv3IfMulticastForwarding OBJECT-TYPE - SYNTAX INTEGER { - blocked(1), -- no multicast forwarding - multicast(2), -- using multicast address - unicast(3) -- to each OSPFv3 neighbor - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The way multicasts should forwarded on this - interface; not forwarded, forwarded as data - link multicasts, or forwarded as data link uni- - casts. Data link multicasting is not meaning- - ful on point to point and NBMA interfaces, and - setting ospfv3MulticastForwarding to 0 effective- - ly disables all multicast forwarding." - DEFVAL { blocked } - ::= { ospfv3IfEntry 18 } - -ospfv3IfDemand OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Indicates whether Demand OSPFv3 procedures (hel- - lo suppression to FULL neighbors and setting the - DoNotAge flag on propagated LSAs) should be per- - formed on this interface." - DEFVAL { false } - ::= { ospfv3IfEntry 19 } - -ospfv3IfMetricValue OBJECT-TYPE - SYNTAX Metric - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The metric assigned to this interface. - The default value of the Metric is - Reference Bandwidth / ifSpeed. The value of the - reference bandwidth is configured by the - ospfv3ReferenceBandwidth object." - ::= { ospfv3IfEntry 20 } - - ospfv3IfLinkScopeLsaCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The total number of Link-Scope link-state - advertisements in this link's link-state database." - ::= { ospfv3IfEntry 21 } - - ospfv3IfLinkLsaCksumSum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32-bit unsigned sum of the Link-Scope link-state - advertisements' LS checksums contained in this - link's link-state database. The sum can be used - to determine if there has been a change in a - router's link state database, and to compare the - link-state database of two routers." - ::= { ospfv3IfEntry 22 } - -ospfv3IfInstId OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Enables multiple instances of OSPFv3 to be run over - a single link. Each protocol instance would be assigned - a separate ID. This ID has local link significance - only." - DEFVAL { 0 } - ::= { ospfv3IfEntry 23 } - -ospfv3IfDemandNbrProbe OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-create - STATUS current - DESCRIPTION - " Indicates whether or not neighbor probing is - enabled to determine whether or not the neighbor - is inactive. Neighbor probing is disabled by - default." - DEFVAL { false } - ::= { ospfv3IfEntry 24 } - - ospfv3IfDemandNbrProbeRetxLimit OBJECT-TYPE - SYNTAX Unsigned32 - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - " The number of consecutive LSA retransmissions before - the neighbor is deemed inactive and the neighbor - adjacency is brought down." - DEFVAL { 10 } - ::= { ospfv3IfEntry 25 } - - - ospfv3IfDemandNbrProbeInterval OBJECT-TYPE - SYNTAX Unsigned32 - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - " Defines how often the neighbor will be probed." - DEFVAL { 120 } - ::= { ospfv3IfEntry 26 } - - --- OSPFv3 Virtual Interface Table - --- The Virtual Interface Table describes the virtual --- links that the OSPFv3 Process is configured to --- carry on. - -ospfv3VirtIfTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3VirtIfEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "Information about this router's virtual inter- - faces." - REFERENCE - "OSPF Version 2, Appendix C.4 Virtual link - parameters" - ::= { ospfv3Objects 8 } - -ospfv3VirtIfEntry OBJECT-TYPE - SYNTAX Ospfv3VirtIfEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "Information about a single Virtual Interface." - INDEX { ospfv3VirtIfAreaId, - ospfv3VirtIfNeighbor } - ::= { ospfv3VirtIfTable 1 } - -Ospfv3VirtIfEntry ::= SEQUENCE { - ospfv3VirtIfAreaId - AreaID, - ospfv3VirtIfNeighbor - RouterID, - ospfv3VirtIfIndex - InterfaceIndex, - ospfv3VirtIfTransitDelay - UpToRefreshInterval, - ospfv3VirtIfRetransInterval - UpToRefreshInterval, - ospfv3VirtIfHelloInterval - HelloRange, - ospfv3VirtIfRtrDeadInterval - RouterDeadRange, - ospfv3VirtIfState - INTEGER, - ospfv3VirtIfEvents - Counter32, - ospfv3VirtIfStatus - RowStatus, - ospfv3VirtIfLinkScopeLsaCount - Gauge32, - ospfv3VirtIfLinkLsaCksumSum - Integer32 - } - -ospfv3VirtIfAreaId OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Transit Area that the Virtual Link - traverses. By definition, this is not 0.0.0.0" - ::= { ospfv3VirtIfEntry 1 } - -ospfv3VirtIfNeighbor OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Router ID of the Virtual Neighbor." - ::= { ospfv3VirtIfEntry 2 } - -ospfv3VirtIfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The interface ID assigned to this OSPFv3 virtual - interface. It is advertised in Hello's sent over - the virtal link and in the router's router-LSAs." - ::= { ospfv3VirtIfEntry 3 } - -ospfv3VirtIfTransitDelay OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The estimated number of seconds it takes to - transmit a link- state update packet over this - interface." - DEFVAL { 1 } - ::= { ospfv3VirtIfEntry 4 } - -ospfv3VirtIfRetransInterval OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The number of seconds between link-state ad- - vertisement retransmissions, for adjacencies - belonging to this interface. This value is - also used when retransmitting database descrip- - tion and link-state request packets. This - value should be well over the expected round- - trip time." - DEFVAL { 5 } - ::= { ospfv3VirtIfEntry 5 } - -ospfv3VirtIfHelloInterval OBJECT-TYPE - SYNTAX HelloRange - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The length of time, in seconds, between the - Hello packets that the router sends on the in- - terface. This value must be the same for the - virtual neighbor." - DEFVAL { 10 } - ::= { ospfv3VirtIfEntry 6 } - -ospfv3VirtIfRtrDeadInterval OBJECT-TYPE - SYNTAX RouterDeadRange - UNITS "seconds" - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The number of seconds that a router's Hello - packets have not been seen before it's neigh- - bors declare the router down. This should be - some multiple of the Hello interval. This - value must be the same for the virtual neigh- - bor." - DEFVAL { 60 } - ::= { ospfv3VirtIfEntry 7 } - -ospfv3VirtIfState OBJECT-TYPE - SYNTAX INTEGER { - down(1), -- these use the same encoding - pointToPoint(4) -- as the ospfv3IfTable - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "OSPF virtual interface states." - ::= { ospfv3VirtIfEntry 8 } - -ospfv3VirtIfEvents OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of state changes or error events on - this Virtual Link" - ::= { ospfv3VirtIfEntry 9 } - -ospfv3VirtIfStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail - in [6]." - ::= { ospfv3VirtIfEntry 10 } - -ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The total number of Link-Scope link-state - advertisements in this virtual link's link-state - database." - ::= { ospfv3VirtIfEntry 11 } - -ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The 32-bit unsigned sum of the Link-Scope link-state - advertisements' LS checksums contained in this - virtual link's link-state database. The sum can be used - to determine if there has been a change in a - router's link state database, and to compare the - link-state database of two routers." - ::= { ospfv3VirtIfEntry 12 } - - --- OSPFv3 Neighbor Table - --- The OSPFv3 Neighbor Table describes all neighbors in --- the locality of the subject router. - -ospfv3NbrTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3NbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A table of non-virtual neighbor information." - REFERENCE - "OSPF Version 2, Section 10 The Neighbor Data - Structure" - ::= { ospfv3Objects 9 } - -ospfv3NbrEntry OBJECT-TYPE - SYNTAX Ospfv3NbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The information regarding a single neighbor." - REFERENCE - "OSPF Version 2, Section 10 The Neighbor Data - Structure" - INDEX { ospfv3NbrIfIndex, - ospfv3NbrRtrId } - ::= { ospfv3NbrTable 1 } - -Ospfv3NbrEntry ::= SEQUENCE { - ospfv3NbrIfIndex - InterfaceIndex, - ospfv3NbrRtrId - RouterID, - ospfv3NbrAddressType - InetAddressType, - ospfv3NbrAddress - InetAddress, - ospfv3NbrOptions - Integer32, - ospfv3NbrPriority - DesignatedRouterPriority, - ospfv3NbrState - INTEGER, - ospfv3NbrEvents - Counter32, - ospfv3NbrLsRetransQLen - Gauge32, - ospfv3NbrHelloSuppressed - TruthValue, - ospfv3NbrIfId - InterfaceIndex, - ospfv3NbrRestartHelperStatus - INTEGER, - ospfv3NbrRestartHelperAge - UpToRefreshInterval, - ospfv3NbrRestartHelperExitReason - INTEGER - } - -ospfv3NbrIfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The local link ID of the link over which the - neighbor can be reached." - ::= { ospfv3NbrEntry 1 } - -ospfv3NbrRtrId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A 32-bit integer (represented as a type IpAd- - dress) uniquely identifying the neighboring - router in the Autonomous System." - ::= { ospfv3NbrEntry 2 } - -ospfv3NbrAddressType OBJECT-TYPE - SYNTAX InetAddressType - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The address type of ospfv3NbrAddress. Only IPv6 - addresses without zone index are expected." - ::= { ospfv3NbrEntry 3 } - -ospfv3NbrAddress OBJECT-TYPE - SYNTAX InetAddress (SIZE (16)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The IPv6 address of the neighbor associated with - the local link." - ::= { ospfv3NbrEntry 4 } - -ospfv3NbrOptions OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A Bit Mask corresponding to the neighbor's op- - tions field." - REFERENCE - "OSPF Version 3, Appendix A.2 the Options field" - ::= { ospfv3NbrEntry 5 } - -ospfv3NbrPriority OBJECT-TYPE - SYNTAX DesignatedRouterPriority - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The priority of this neighbor in the designat- - ed router election algorithm. The value 0 sig- - nifies that the neighbor is not eligible to be- - come the designated router on this particular - network." - ::= { ospfv3NbrEntry 6 } - -ospfv3NbrState OBJECT-TYPE - SYNTAX INTEGER { - down(1), - attempt(2), - init(3), - twoWay(4), - exchangeStart(5), - exchange(6), - loading(7), - full(8) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The State of the relationship with this Neigh- - bor." - REFERENCE - "OSPF Version 2, Section 10.1 Neighbor States" - ::= { ospfv3NbrEntry 7 } - -ospfv3NbrEvents OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of times this neighbor relationship - has changed state, or an error has occurred." - ::= { ospfv3NbrEntry 8 } - -ospfv3NbrLsRetransQLen OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The current length of the retransmission - queue." - ::= { ospfv3NbrEntry 9 } - -ospfv3NbrHelloSuppressed OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates whether Hellos are being suppressed - to the neighbor" - ::= { ospfv3NbrEntry 10 } - -ospfv3NbrIfId OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The interface ID that the neighbor advertises - in its Hello Packets on this link, that is, the - neighbor's local interface index." - ::= { ospfv3NbrEntry 11 } - -ospfv3NbrRestartHelperStatus OBJECT-TYPE - SYNTAX INTEGER { notHelping (1), - helping (2) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates whether the router is acting - as a hitless restart helper for the neighbor." - ::= { ospfv3NbrEntry 12 } - -ospfv3NbrRestartHelperAge OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Remaining time in current OSPF hitless restart - interval, if the router is acting as a restart - helper for the neighbor." - ::= { ospfv3NbrEntry 13 } - -ospfv3NbrRestartHelperExitReason OBJECT-TYPE - SYNTAX INTEGER { none (1), -- not attempted - inProgress (2), -- restart in - -- progress - completed (3), -- successfully - -- completed - timedOut (4), -- timed out - topologyChanged (5) -- aborted due to - -- topology - -- change. - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Describes the outcome of the last attempt at acting - as a hitless restart helper for the neighbor." - ::= { ospfv3NbrEntry 14 } - - --- OSPFv3 NBMA Neighbor Table - --- The OSPFv3 NBMA Neighbor Table describes all configured --- NBMA neighbors and neighbors dynamically discovered by --- lower-level protocols such as Inverse Neighbor Discovery. - -ospfv3NbmaNbrTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3NbmaNbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A table of configured non-virtual neighbor - information and neighbors dynamically discovered - by lower-level protocols such as Inverse Neighbor - Discovery." - REFERENCE - "OSPF Version 2, Section 10 The Neighbor Data - Structure" - ::= { ospfv3Objects 10 } - -ospfv3NbmaNbrEntry OBJECT-TYPE - SYNTAX Ospfv3NbmaNbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "The information regarding a single configured - neighbor or neighbor discovered by lower-level - protocols such as Inverse Neighbor Discovery." - REFERENCE - "OSPF Version 2, Section 10 The Neighbor Data - Structure" - INDEX { ospfv3NbmaNbrIfIndex, - ospfv3NbmaNbrAddressType, - ospfv3NbmaNbrAddress } - ::= { ospfv3NbmaNbrTable 1 } - -Ospfv3NbmaNbrEntry ::= SEQUENCE { - ospfv3NbmaNbrIfIndex - InterfaceIndex, - ospfv3NbmaNbrAddressType - InetAddressType, - ospfv3NbmaNbrAddress - InetAddress, - ospfv3NbmaNbrPriority - DesignatedRouterPriority, - ospfv3NbmaNbrRtrId - RouterID, - ospfv3NbmaNbrState - INTEGER, - ospfv3NbmaNbrStorageType - StorageType, - ospfv3NbmaNbrStatus - RowStatus - } - -ospfv3NbmaNbrIfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The local link ID of the link over which the - neighbor can be reached." - ::= { ospfv3NbmaNbrEntry 1 } - -ospfv3NbmaNbrAddressType OBJECT-TYPE - SYNTAX InetAddressType - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The address type of ospfv3NbrAddress. Only IPv6 - addresses without zone index are expected." - ::= { ospfv3NbmaNbrEntry 2 } - -ospfv3NbmaNbrAddress OBJECT-TYPE - SYNTAX InetAddress (SIZE (16)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The IPv6 address of the neighbor associated with - the local link." - ::= { ospfv3NbmaNbrEntry 3 } - -ospfv3NbmaNbrPriority OBJECT-TYPE - SYNTAX DesignatedRouterPriority - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The priority of this neighbor in the designat- - ed router election algorithm. The value 0 sig- - nifies that the neighbor is not eligible to be- - come the designated router on this particular - network." - DEFVAL { 1 } - ::= { ospfv3NbmaNbrEntry 4 } - -ospfv3NbmaNbrRtrId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A 32-bit integer (represented as a type IpAd- - dress) uniquely identifying the neighboring - router in the Autonomous System. A value of - 0.0.0.0 is returned until a Hello is received - from the configured neighbor." - ::= { ospfv3NbmaNbrEntry 5 } - -ospfv3NbmaNbrState OBJECT-TYPE - SYNTAX INTEGER { - down(1), - attempt(2), - init(3), - twoWay(4), - exchangeStart(5), - exchange(6), - loading(7), - full(8) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The State of the relationship with this Neigh- - bor." - REFERENCE - "OSPF Version 2, Section 10.1 Neighbor States" - ::= { ospfv3NbmaNbrEntry 6 } - -ospfv3NbmaNbrStorageType OBJECT-TYPE - SYNTAX StorageType - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "The storage type for this conceptual row. - Conceptual rows having the value 'permanent' need not - allow write-access to any columnar objects in the row. - Manually configured entries will have a storage type - of nonVolatile while entries dynamically created as a - result of a lower-level protocol such as Inverse - Neighbor Discovery will have a storage type of - volatile." - DEFVAL { nonVolatile } - ::= { ospfv3NbmaNbrEntry 7 } - -ospfv3NbmaNbrStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail - in [6]." - ::= { ospfv3NbmaNbrEntry 8 } - --- OSPFv3 Virtual Neighbor Table - --- This table describes all virtual neighbors. --- Since Virtual Links are configured in the --- virtual interface table, this table is read-only. - -ospfv3VirtNbrTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3VirtNbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A table of virtual neighbor information." - REFERENCE - "OSPF Version 2, Section 15 Virtual Links" - ::= { ospfv3Objects 11 } - -ospfv3VirtNbrEntry OBJECT-TYPE - SYNTAX Ospfv3VirtNbrEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "Virtual neighbor information." - INDEX { ospfv3VirtNbrArea, - ospfv3VirtNbrRtrId } - ::= { ospfv3VirtNbrTable 1 } - -Ospfv3VirtNbrEntry ::= SEQUENCE { - ospfv3VirtNbrArea - AreaID, - ospfv3VirtNbrRtrId - RouterID, - ospfv3VirtNbrIfIndex - InterfaceIndex, - ospfv3VirtNbrAddressType - InetAddressType, - ospfv3VirtNbrAddress - InetAddress, - ospfv3VirtNbrOptions - Integer32, - ospfv3VirtNbrState - INTEGER, - ospfv3VirtNbrEvents - Counter32, - ospfv3VirtNbrLsRetransQLen - Gauge32, - ospfv3VirtNbrHelloSuppressed - TruthValue, - ospfv3VirtNbrIfId - InterfaceIndex, - ospfv3VirtNbrRestartHelperStatus - INTEGER, - ospfv3VirtNbrRestartHelperAge - UpToRefreshInterval, - ospfv3VirtNbrRestartHelperExitReason - INTEGER - } - -ospfv3VirtNbrArea OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Transit Area Identifier." - ::= { ospfv3VirtNbrEntry 1 } - -ospfv3VirtNbrRtrId OBJECT-TYPE - SYNTAX RouterID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A 32-bit integer uniquely identifying the - neighboring router in the Autonomous System." - ::= { ospfv3VirtNbrEntry 2 } - -ospfv3VirtNbrIfIndex OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The local interface ID for the virtual link over - which the neighbor can be reached." - ::= { ospfv3VirtNbrEntry 3 } - -ospfv3VirtNbrAddressType OBJECT-TYPE - SYNTAX InetAddressType - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The address type of ospfv3VirtNbrAddress. Only IPv6 - addresses without zone index are expected." - ::= { ospfv3VirtNbrEntry 4 } - -ospfv3VirtNbrAddress OBJECT-TYPE - SYNTAX InetAddress (SIZE (16)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The IPv6 address advertised by this Virtual Neighbor. - It must be a Site-Local or Global scope address." - ::= { ospfv3VirtNbrEntry 5 } - -ospfv3VirtNbrOptions OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "A Bit Mask corresponding to the neighbor's op- - tions field." - REFERENCE - "OSPF Version 3, Appendix A.2 the Options field" - ::= { ospfv3VirtNbrEntry 6 } - -ospfv3VirtNbrState OBJECT-TYPE - SYNTAX INTEGER { - down(1), - attempt(2), - init(3), - twoWay(4), - exchangeStart(5), - exchange(6), - loading(7), - full(8) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The state of the Virtual Neighbor Relation- - ship." - ::= { ospfv3VirtNbrEntry 7 } - -ospfv3VirtNbrEvents OBJECT-TYPE - SYNTAX Counter32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The number of times this virtual link has - changed its state, or an error has occurred." - ::= { ospfv3VirtNbrEntry 8 } - -ospfv3VirtNbrLsRetransQLen OBJECT-TYPE - SYNTAX Gauge32 - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The current length of the retransmission - queue." - ::= { ospfv3VirtNbrEntry 9 } - -ospfv3VirtNbrHelloSuppressed OBJECT-TYPE - SYNTAX TruthValue - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates whether Hellos are being suppressed - to the neighbor" - ::= { ospfv3VirtNbrEntry 10 } - -ospfv3VirtNbrIfId OBJECT-TYPE - SYNTAX InterfaceIndex - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The interface ID that the neighbor advertises - in its Hello Packets on this virtual link, that is, - the neighbor's local interface ID." - ::= { ospfv3VirtNbrEntry 11 } - - ospfv3VirtNbrRestartHelperStatus OBJECT-TYPE - SYNTAX INTEGER { notHelping (1), - helping (2) - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Indicates whether the router is acting - as a hitless restart helper for the neighbor." - ::= { ospfv3VirtNbrEntry 12 } - -ospfv3VirtNbrRestartHelperAge OBJECT-TYPE - SYNTAX UpToRefreshInterval - UNITS "seconds" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Remaining time in current OSPF hitless restart - interval, if the router is acting as a restart - helper for the neighbor." - ::= { ospfv3VirtNbrEntry 13 } - -ospfv3VirtNbrRestartHelperExitReason OBJECT-TYPE - SYNTAX INTEGER { none (1), -- not attempted - inProgress (2), -- restart in - -- progress - completed (3), -- successfully - -- completed - timedOut (4), -- timed out - topologyChanged (5) -- aborted due to - -- topology - -- change. - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "Describes the outcome of the last attempt at acting - as a hitless restart helper for the neighbor." - ::= { ospfv3VirtNbrEntry 14 } - - --- --- The OSPFv3 Area Aggregate Table --- - -ospfv3AreaAggregateTable OBJECT-TYPE - SYNTAX SEQUENCE OF Ospfv3AreaAggregateEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A range of IPv6 prefixes specified by a - prefix/prefix length pair. Note that if - ranges are configured such that one range sub- - sumes another range the most specific match is - the preferred one." - ::= { ospfv3Objects 12 } - -ospfv3AreaAggregateEntry OBJECT-TYPE - SYNTAX Ospfv3AreaAggregateEntry - MAX-ACCESS not-accessible - STATUS current - DESCRIPTION - "A range of IPv6 prefixes specified by a - prefix/prefix length pair. Note that if - ranges are configured such that one range sub- - sumes another range the most specific match is - the preferred one." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - INDEX { ospfv3AreaAggregateAreaID, - ospfv3AreaAggregateAreaLsdbType, - ospfv3AreaAggregatePrefixType, - ospfv3AreaAggregatePrefix, - ospfv3AreaAggregatePrefixLength } - ::= { ospfv3AreaAggregateTable 1 } - -Ospfv3AreaAggregateEntry ::= SEQUENCE { - ospfv3AreaAggregateAreaID - AreaID, - ospfv3AreaAggregateAreaLsdbType - INTEGER, - ospfv3AreaAggregatePrefixType - InetAddressType, - ospfv3AreaAggregatePrefix - InetAddress, - ospfv3AreaAggregatePrefixLength - InetAddressPrefixLength, - ospfv3AreaAggregateStatus - RowStatus, - ospfv3AreaAggregateEffect - INTEGER, - ospfv3AreaAggregateRouteTag - INTEGER - } - -ospfv3AreaAggregateAreaID OBJECT-TYPE - SYNTAX AreaID - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The Area the Address Aggregate is to be found - within." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3AreaAggregateEntry 1 } - -ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE - SYNTAX INTEGER { - interAreaPrefixLsa(8195), -- 0x2003 - nssaExternalLsa(8199) -- 0x2007 - } - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The type of the Address Aggregate. This field - specifies the Area Lsdb type that this Address Ag- - gregate applies to." - REFERENCE - "OSPF Version 2, Appendix A.4.1 The Link State - Advertisement header" - ::= { ospfv3AreaAggregateEntry 2 } - -ospfv3AreaAggregatePrefixType OBJECT-TYPE - SYNTAX InetAddressType - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The prefix type of ospfv3AreaAggregatePrefix. Only - IPv6 addresses are expected." - ::= { ospfv3AreaAggregateEntry 4 } - -ospfv3AreaAggregatePrefix OBJECT-TYPE - SYNTAX InetAddress (SIZE (0..16)) - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The IPv6 Prefix." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3AreaAggregateEntry 5 } - -ospfv3AreaAggregatePrefixLength OBJECT-TYPE - SYNTAX InetAddressPrefixLength (3..128) - UNITS "bits" - MAX-ACCESS read-only - STATUS current - DESCRIPTION - "The length of the prefix (in bits). A prefix can - not be shorter than 3 bits." - REFERENCE - "OSPF Version 2, Appendix C.2 Area parameters" - ::= { ospfv3AreaAggregateEntry 6 } - -ospfv3AreaAggregateStatus OBJECT-TYPE - SYNTAX RowStatus - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This variable controls the status of the en- - try. The use of RowStatus is covered in more detail - in [6]." - ::= { ospfv3AreaAggregateEntry 7 } - -ospfv3AreaAggregateEffect OBJECT-TYPE - SYNTAX INTEGER { - advertiseMatching(1), - doNotAdvertiseMatching(2) - } - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "Prefixes subsumed by ranges either trigger the - advertisement of the indicated aggregate (ad- - vertiseMatching), or result in the prefix not - being advertised at all outside the area." - DEFVAL { advertiseMatching } - ::= { ospfv3AreaAggregateEntry 8 } - -ospfv3AreaAggregateRouteTag OBJECT-TYPE - SYNTAX Integer32 - MAX-ACCESS read-create - STATUS current - DESCRIPTION - "This tag is advertised only in the summarized - As-External LSA when summarizing from type-7 to - type-5." - DEFVAL { 0 } - ::= { ospfv3AreaAggregateEntry 9 } - - --- conformance information - -ospfv3Groups OBJECT IDENTIFIER ::= { ospfv3Conformance 1 } -ospfv3Compliances OBJECT IDENTIFIER ::= { ospfv3Conformance 2 } - --- compliance statements - -ospfv3Compliance MODULE-COMPLIANCE - STATUS current - DESCRIPTION "The compliance statement " - MODULE -- this module - MANDATORY-GROUPS { - ospfv3BasicGroup, - ospfv3AreaGroup, - ospfv3IfGroup, - ospfv3VirtIfGroup, - ospfv3NbrGroup, - ospfv3NbmaNbrGroup, - ospfv3VirtNbrGroup, - ospfv3AreaAggregateGroup - } - - GROUP ospfv3AsLsdbGroup - DESCRIPTION - "This group is required for OSPFv3 systems that - display their AS-scope link state database." - - GROUP ospfv3AreaLsdbGroup - DESCRIPTION - "This group is required for OSPFv3 systems that - display their Area-scope link state database." - - GROUP ospfv3LinkLsdbGroup - DESCRIPTION - "This group is required for OSPFv3 systems that - display their Link-scope link state database." - - GROUP ospfv3HostGroup - DESCRIPTION - "This group is required for OSPFv3 systems that - support attached hosts." - - OBJECT ospfv3NbrAddressType - SYNTAX InetAddressType { ipv6(2) } - DESCRIPTION - "An implementation is only required to support IPv6 - address without zone index." - - OBJECT ospfv3VirtNbrAddressType - SYNTAX InetAddressType { ipv6(2) } - DESCRIPTION - "An implementation is only required to support IPv6 - address without zone index." - - ::= { ospfv3Compliances 1 } - --- units of conformance - -ospfv3BasicGroup OBJECT-GROUP - OBJECTS { - ospfv3RouterId, - ospfv3AdminStat, - ospfv3VersionNumber, - ospfv3AreaBdrRtrStatus, - ospfv3ASBdrRtrStatus, - ospfv3AsScopeLsaCount, - ospfv3AsScopeLsaCksumSum, - ospfv3OriginateNewLsas, - ospfv3RxNewLsas, - ospfv3ExtLsaCount, - ospfv3ExtAreaLsdbLimit, - ospfv3MulticastExtensions, - ospfv3ExitOverflowInterval, - ospfv3DemandExtensions, - ospfv3TrafficEngineeringSupport, - ospfv3ReferenceBandwidth, - ospfv3RestartSupport, - ospfv3RestartInterval, - ospfv3RestartStatus, - ospfv3RestartAge, - ospfv3RestartExitReason - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems." - ::= { ospfv3Groups 1 } - - -ospfv3AreaGroup OBJECT-GROUP - OBJECTS { - ospfv3ImportAsExtern, - ospfv3AreaSpfRuns, - ospfv3AreaBdrRtrCount, - ospfv3AreaAsBdrRtrCount, - ospfv3AreaScopeLsaCount, - ospfv3AreaScopeLsaCksumSum, - ospfv3AreaSummary, - ospfv3AreaStatus, - ospfv3StubMetric, - ospfv3AreaNssaTranslatorRole, - ospfv3AreaNssaTranslatorState, - ospfv3AreaNssaTranslatorStabilityInterval, - ospfv3AreaNssaTranslatorEvents, - ospfv3AreaStubMetricType - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems - supporting areas." - ::= { ospfv3Groups 2 } - -ospfv3AsLsdbGroup OBJECT-GROUP - OBJECTS { - ospfv3AsLsdbSequence, - ospfv3AsLsdbAge, - ospfv3AsLsdbChecksum, - ospfv3AsLsdbAdvertisement, - ospfv3AsLsdbTypeKnown - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems - that display their AS-scope link state database." - ::= { ospfv3Groups 3 } - -ospfv3AreaLsdbGroup OBJECT-GROUP - OBJECTS { - ospfv3AreaLsdbSequence, - ospfv3AreaLsdbAge, - ospfv3AreaLsdbChecksum, - ospfv3AreaLsdbAdvertisement, - ospfv3AreaLsdbTypeKnown - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems - that display their Area-scope link state database." - ::= { ospfv3Groups 4 } - -ospfv3LinkLsdbGroup OBJECT-GROUP - OBJECTS { - ospfv3LinkLsdbSequence, - ospfv3LinkLsdbAge, - ospfv3LinkLsdbChecksum, - ospfv3LinkLsdbAdvertisement, - ospfv3LinkLsdbTypeKnown - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems - that display their Link-scope link state database." - ::= { ospfv3Groups 5 } - -ospfv3HostGroup OBJECT-GROUP - OBJECTS { - ospfv3HostMetric, - ospfv3HostStatus, - ospfv3HostAreaID - } - STATUS current - DESCRIPTION - "These objects are required for OSPFv3 systems - that support attached hosts." - ::= { ospfv3Groups 6 } - -ospfv3IfGroup OBJECT-GROUP - OBJECTS { - ospfv3IfAreaId, - ospfv3IfType, - ospfv3IfAdminStat, - ospfv3IfRtrPriority, - ospfv3IfTransitDelay, - ospfv3IfRetransInterval, - ospfv3IfHelloInterval, - ospfv3IfRtrDeadInterval, - ospfv3IfPollInterval, - ospfv3IfState, - ospfv3IfDesignatedRouter, - ospfv3IfBackupDesignatedRouter, - ospfv3IfEvents, - ospfv3IfStatus, - ospfv3IfMulticastForwarding, - ospfv3IfDemand, - ospfv3IfMetricValue, - ospfv3IfLinkScopeLsaCount, - ospfv3IfLinkLsaCksumSum, - ospfv3IfInstId, - ospfv3IfDemandNbrProbe, - ospfv3IfDemandNbrProbeRetxLimit, - ospfv3IfDemandNbrProbeInterval - } - STATUS current - DESCRIPTION - "These interface objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 7 } - -ospfv3VirtIfGroup OBJECT-GROUP - OBJECTS { - ospfv3VirtIfIndex, - ospfv3VirtIfTransitDelay, - ospfv3VirtIfRetransInterval, - ospfv3VirtIfHelloInterval, - ospfv3VirtIfRtrDeadInterval, - ospfv3VirtIfState, - ospfv3VirtIfEvents, - ospfv3VirtIfStatus, - ospfv3VirtIfLinkScopeLsaCount, - ospfv3VirtIfLinkLsaCksumSum - } - STATUS current - DESCRIPTION - "These virtual interface objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 8 } - -ospfv3NbrGroup OBJECT-GROUP - OBJECTS { - ospfv3NbrAddressType, - ospfv3NbrAddress, - ospfv3NbrOptions, - ospfv3NbrPriority, - ospfv3NbrState, - ospfv3NbrEvents, - ospfv3NbrLsRetransQLen, - ospfv3NbrHelloSuppressed, - ospfv3NbrIfId, - ospfv3NbrRestartHelperStatus, - ospfv3NbrRestartHelperAge, - ospfv3NbrRestartHelperExitReason - } - STATUS current - DESCRIPTION - "These neighbor objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 9 } - -ospfv3NbmaNbrGroup OBJECT-GROUP - OBJECTS { - ospfv3NbmaNbrPriority, - ospfv3NbmaNbrRtrId, - ospfv3NbmaNbrState, - ospfv3NbmaNbrStorageType, - ospfv3NbmaNbrStatus - } - STATUS current - DESCRIPTION - "These NBMA neighbor objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 10 } - -ospfv3VirtNbrGroup OBJECT-GROUP - OBJECTS { - ospfv3VirtNbrIfIndex, - ospfv3VirtNbrAddressType, - ospfv3VirtNbrAddress, - ospfv3VirtNbrOptions, - ospfv3VirtNbrState, - ospfv3VirtNbrEvents, - ospfv3VirtNbrLsRetransQLen, - ospfv3VirtNbrHelloSuppressed, - ospfv3VirtNbrIfId, - ospfv3VirtNbrRestartHelperStatus, - ospfv3VirtNbrRestartHelperAge, - ospfv3VirtNbrRestartHelperExitReason - } - STATUS current - DESCRIPTION - "These virtual neighbor objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 11 } - -ospfv3AreaAggregateGroup OBJECT-GROUP - OBJECTS { - ospfv3AreaAggregateStatus, - ospfv3AreaAggregateEffect, - ospfv3AreaAggregateRouteTag - } - STATUS current - DESCRIPTION - "These area aggregate objects are required for - OSPFv3 systems." - ::= { ospfv3Groups 12 } - -END + OSPFV3-MIB DEFINITIONS ::= BEGIN + + IMPORTS + MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, + Counter32, Gauge32, Integer32, Unsigned32 + FROM SNMPv2-SMI + TEXTUAL-CONVENTION, TruthValue, RowStatus, TimeStamp + FROM SNMPv2-TC + MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP + FROM SNMPv2-CONF + InterfaceIndex + FROM IF-MIB + InetAddressType, InetAddress, InetAddressPrefixLength, + InetAddressIPv6 + FROM INET-ADDRESS-MIB + Metric, BigMetric, Status, + HelloRange, DesignatedRouterPriority + FROM OSPF-MIB; + + ospfv3MIB MODULE-IDENTITY + LAST-UPDATED "200908130000Z" + ORGANIZATION "IETF OSPF Working Group" + CONTACT-INFO + "WG E-Mail: ospf@ietf.org + WG Chairs: Acee Lindem + acee@redback.com + + Abhay Roy + akr@cisco.com + + Editors: Dan Joyal + Nortel + 600 Technology Park Drive + Billerica, MA 01821, USA + djoyal@nortel.com + + Vishwas Manral + IP Infusion + Almora, Uttarakhand + India + vishwas@ipinfusion.com" + DESCRIPTION + "The MIB module for OSPF version 3. + + Copyright (c) 2009 IETF Trust and the persons + identified as authors of the code. All rights + reserved. + + Redistribution and use in source and binary forms, with + or without modification, are permitted provided that + the following conditions are met: + + - Redistributions of source code must retain the above + copyright notice, this list of conditions and the + following disclaimer. + + - Redistributions in binary form must reproduce the + above copyright notice, this list of conditions and + the following disclaimer in the documentation and/or + other materials provided with the distribution. + + - Neither the name of Internet Society, IETF or IETF + Trust, nor the names of specific contributors, may be + used to endorse or promote products derived from this + software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND + CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED + WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A + PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL + THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY + DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, + PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER + IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING + NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE + USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + + This version of this MIB module is part of RFC 5643; + see the RFC itself for full legal notices." + + REVISION "200908130000Z" + DESCRIPTION + "Initial version, published as RFC 5643" + ::= { mib-2 191 } + + -- Textual conventions + + Ospfv3UpToRefreshIntervalTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "The values one might be able to configure for + variables bounded by the Refresh Interval." + REFERENCE + "OSPF Version 2, Appendix B, Architectural Constants" + SYNTAX Unsigned32 (1..1800) + + Ospfv3DeadIntervalRangeTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "The range, in seconds, of dead interval value." + REFERENCE + "OSPF for IPv6, Appendix C.3, Router Interface + Parameters" + SYNTAX Unsigned32 (1..'FFFF'h) + + Ospfv3RouterIdTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "A 32-bit, unsigned integer uniquely identifying the + router in the Autonomous System. To ensure + uniqueness, this may default to the value of one of + the router's IPv4 host addresses if IPv4 is + configured on the router." + REFERENCE + "OSPF for IPv6, Appendix C.1, Global Parameters" + SYNTAX Unsigned32 (1..'FFFFFFFF'h) + + Ospfv3LsIdTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "A unique 32-bit identifier of the piece of the + routing domain that is being described by a link + state advertisement. In contrast to OSPFv2, the + Link State ID (LSID) has no addressing semantics." + REFERENCE + "OSPF Version 2, Section 12.1.4, Link State ID" + SYNTAX Unsigned32 (1..'FFFFFFFF'h) + + Ospfv3AreaIdTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "An OSPFv3 Area Identifier. A value of zero + identifies the backbone area." + REFERENCE + "OSPF for IPv6, Appendix C.3 Router Interface + Parameters" + SYNTAX Unsigned32 (0..'FFFFFFFF'h) + + Ospfv3IfInstIdTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "An OSPFv3 Interface Instance ID." + REFERENCE + "OSPF for IPv6, Appendix C.3, Router Interface + Parameters" + SYNTAX Unsigned32 (0..255) + + Ospfv3LsaSequenceTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "The sequence number field is a signed 32-bit + integer. It is used to detect old and duplicate + link state advertisements. The space of + sequence numbers is linearly ordered. The + larger the sequence number, the more recent the + advertisement." + REFERENCE + "OSPF Version 2, Section 12.1.6, LS sequence + number" + SYNTAX Integer32 + + Ospfv3LsaAgeTC ::= TEXTUAL-CONVENTION + DISPLAY-HINT "d" + STATUS current + DESCRIPTION + "The age of the link state advertisement in + seconds. The high-order bit of the LS age + field is considered the DoNotAge bit for + support of on-demand circuits." + REFERENCE + "OSPF Version 2, Section 12.1.1, LS age; + Extending OSPF to Support Demand Circuits, + Section 2.2, The LS age field" + SYNTAX Unsigned32 (0..3600 | 32768..36368) + + -- Top-level structure of MIB + ospfv3Notifications OBJECT IDENTIFIER ::= { ospfv3MIB 0 } + ospfv3Objects OBJECT IDENTIFIER ::= { ospfv3MIB 1 } + ospfv3Conformance OBJECT IDENTIFIER ::= { ospfv3MIB 2 } + + -- OSPFv3 General Variables + + -- These parameters apply globally to the Router's + -- OSPFv3 Process. + + ospfv3GeneralGroup OBJECT IDENTIFIER ::= { ospfv3Objects 1 } + + ospfv3RouterId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "A 32-bit unsigned integer uniquely identifying + the router in the Autonomous System. To ensure + uniqueness, this may default to the 32-bit + unsigned integer representation of one of + the router's IPv4 interface addresses (if IPv4 + is configured on the router). + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE + "OSPF for IPv6, Appendix C.1, Global Parameters" + ::= { ospfv3GeneralGroup 1 } + + ospfv3AdminStatus OBJECT-TYPE + SYNTAX Status + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The administrative status of OSPFv3 in the + router. The value 'enabled' denotes that the + OSPFv3 Process is active on at least one + interface; 'disabled' disables it on all + interfaces. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + ::= { ospfv3GeneralGroup 2 } + + ospfv3VersionNumber OBJECT-TYPE + SYNTAX INTEGER { version3 (3) } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The version number of OSPF for IPv6 is 3." + ::= { ospfv3GeneralGroup 3 } + + ospfv3AreaBdrRtrStatus OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A flag to denote whether this router is an area + border router. The value of this object is true (1) + when the router is an area border router." + REFERENCE + "OSPF Version 2, Section 3, Splitting the AS into + Areas" + ::= { ospfv3GeneralGroup 4 } + + ospfv3ASBdrRtrStatus OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "A flag to note whether this router is + configured as an Autonomous System border router. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE + "OSPF Version 2, Section 3.3, Classification of + routers" + ::= { ospfv3GeneralGroup 5 } + + ospfv3AsScopeLsaCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of AS-scope (e.g., AS-External) link state + advertisements in the link state database." + ::= { ospfv3GeneralGroup 6 } + + ospfv3AsScopeLsaCksumSum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 32-bit unsigned sum of the LS checksums of + the AS-scoped link state advertisements + contained in the link state database. This sum + can be used to determine if there has been a + change in a router's link state database or + to compare the link state database of two + routers." + ::= { ospfv3GeneralGroup 7 } + + ospfv3OriginateNewLsas OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of new link state advertisements + that have been originated. This number is + incremented each time the router originates a new + LSA. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3GeneralGroup 8 } + + ospfv3RxNewLsas OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of link state advertisements + received that are determined to be new + instantiations. This number does not include + newer instantiations of self-originated link state + advertisements. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3GeneralGroup 9 } + + ospfv3ExtLsaCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of External (LS type 0x4005) in the + link state database." + ::= { ospfv3GeneralGroup 10 } + + ospfv3ExtAreaLsdbLimit OBJECT-TYPE + SYNTAX Integer32 (-1..'7FFFFFFF'h) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The maximum number of non-default + AS-external-LSA entries that can be stored in the + link state database. If the value is -1, then + there is no limit. + + When the number of non-default AS-external-LSAs + in a router's link state database reaches + ospfv3ExtAreaLsdbLimit, the router enters Overflow + state. The router never holds more than + ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs + in its database. ospfv3ExtAreaLsdbLimit MUST be set + identically in all routers attached to the OSPFv3 + backbone and/or any regular OSPFv3 area (i.e., + OSPFv3 stub areas and not-so-stubby-areas (NSSAs) + are excluded). + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + ::= { ospfv3GeneralGroup 11 } + + ospfv3ExitOverflowInterval OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "seconds" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The number of seconds that, after entering + Overflow state, a router will attempt to leave + Overflow state. This allows the router to again + originate non-default, AS-External-LSAs. When + set to 0, the router will not leave Overflow + state until restarted. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + ::= { ospfv3GeneralGroup 12 } + + ospfv3DemandExtensions OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The router's support for demand circuits. + The value of this object is true (1) when + demand circuits are supported. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE + "OSPF Version 2; Extending OSPF to Support Demand + Circuits" + ::= { ospfv3GeneralGroup 13 } + + ospfv3ReferenceBandwidth OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "kilobits per second" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Reference bandwidth in kilobits per second for + calculating default interface metrics. The + default value is 100,000 KBPS (100 MBPS). + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE + "OSPF Version 2, Appendix C.3, Router interface + parameters" + DEFVAL { 100000 } + ::= { ospfv3GeneralGroup 14 } + + ospfv3RestartSupport OBJECT-TYPE + SYNTAX INTEGER { none(1), + plannedOnly(2), + plannedAndUnplanned(3) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "The router's support for OSPF graceful restart. + Options include no restart support, only planned + + restarts, or both planned and unplanned restarts. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE "Graceful OSPF Restart, Appendix B.1, Global + Parameters (Minimum subset)" + ::= { ospfv3GeneralGroup 15 } + + ospfv3RestartInterval OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Configured OSPF graceful restart timeout interval. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + REFERENCE "Graceful OSPF Restart, Appendix B.1, Global + Parameters (Minimum subset)" + DEFVAL { 120 } + ::= { ospfv3GeneralGroup 16 } + + ospfv3RestartStrictLsaChecking OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "Indicates if strict LSA checking is enabled for + graceful restart. A value of true (1) indicates that + strict LSA checking is enabled. + + This object is persistent, and when written, + the entity SHOULD save the change to non-volatile + storage." + REFERENCE "Graceful OSPF Restart, Appendix B.2, Global + Parameters (Optional)" + DEFVAL { true } + ::= { ospfv3GeneralGroup 17 } + + ospfv3RestartStatus OBJECT-TYPE + SYNTAX INTEGER { notRestarting(1), + plannedRestart(2), + unplannedRestart(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current status of OSPF graceful restart capability." + ::= { ospfv3GeneralGroup 18 } + + ospfv3RestartAge OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Remaining time in the current OSPF graceful restart + interval." + ::= { ospfv3GeneralGroup 19 } + + ospfv3RestartExitReason OBJECT-TYPE + SYNTAX INTEGER { none(1), + inProgress(2), + completed(3), + timedOut(4), + topologyChanged(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Describes the outcome of the last attempt at a + graceful restart. + + none: no restart has yet been attempted. + inProgress: a restart attempt is currently underway. + completed: the last restart completed successfully. + timedOut: the last restart timed out. + topologyChanged: the last restart was aborted due to + a topology change." + ::= { ospfv3GeneralGroup 20 } + + ospfv3NotificationEnable OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object provides a coarse level of control + over the generation of OSPFv3 notifications. + + If this object is set to true (1), then it enables + the generation of OSPFv3 notifications. If it is + set to false (2), these notifications are not + generated. + + This object is persistent, and when written, the + entity SHOULD save the change to non-volatile + storage." + ::= { ospfv3GeneralGroup 21 } + +ospfv3StubRouterSupport OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The router's support for stub router functionality. An + object value of true (1) indicates that stub router + functionality is supported." + REFERENCE + "OSPF Stub Router Advertisement" + ::= { ospfv3GeneralGroup 22 } + + ospfv3StubRouterAdvertisement OBJECT-TYPE + SYNTAX INTEGER { + doNotAdvertise(1), + advertise(2) + } + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object controls the advertisement of + stub LSAs by the router. The value + doNotAdvertise (1) will result in the advertisement + of standard LSAs and is the default value. + + This object is persistent, and when written, + the entity SHOULD save the change to non-volatile + storage." + REFERENCE + "OSPF Stub Router Advertisement, Section 2, Proposed + Solution" + DEFVAL { doNotAdvertise } + ::= { ospfv3GeneralGroup 23 } + +ospfv3DiscontinuityTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which any one of this MIB's counters suffered + a discontinuity. + + If no such discontinuities have occurred since the last + re-initialization of the local management subsystem, + then this object contains a zero value." + ::= { ospfv3GeneralGroup 24 } + + ospfv3RestartTime OBJECT-TYPE + SYNTAX TimeStamp + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of sysUpTime on the most recent occasion + at which the ospfv3RestartExitReason was updated." + ::= { ospfv3GeneralGroup 25 } + + -- The OSPFv3 Area Data Structure contains information + -- regarding the various areas. The interfaces and + -- virtual links are configured as part of these areas. + -- Area 0, by definition, is the backbone area. + + ospfv3AreaTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3AreaEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information describing the configured + parameters and cumulative statistics of the router's + attached areas. The interfaces and + virtual links are configured as part of these areas. + Area 0, by definition, is the backbone area." + REFERENCE + "OSPF Version 2, Section 6, The Area Data + Structure" + ::= { ospfv3Objects 2 } + + ospfv3AreaEntry OBJECT-TYPE + SYNTAX Ospfv3AreaEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information describing the configured + parameters and cumulative statistics of one of the + router's attached areas. + + The information in this table is persistent, + and when written, the entity SHOULD save the a + change to non-volatile storage." + INDEX { ospfv3AreaId } + ::= { ospfv3AreaTable 1 } + + Ospfv3AreaEntry ::= SEQUENCE { + ospfv3AreaId + Ospfv3AreaIdTC, + ospfv3AreaImportAsExtern + INTEGER, + ospfv3AreaSpfRuns + Counter32, + ospfv3AreaBdrRtrCount + Gauge32, + ospfv3AreaAsBdrRtrCount + Gauge32, + ospfv3AreaScopeLsaCount + Gauge32, + ospfv3AreaScopeLsaCksumSum + Unsigned32, + ospfv3AreaSummary + INTEGER, + ospfv3AreaRowStatus + RowStatus, + ospfv3AreaStubMetric + BigMetric, + ospfv3AreaNssaTranslatorRole + INTEGER, + ospfv3AreaNssaTranslatorState + INTEGER, + ospfv3AreaNssaTranslatorStabInterval + Unsigned32, + ospfv3AreaNssaTranslatorEvents + Counter32, + ospfv3AreaStubMetricType + INTEGER, + ospfv3AreaTEEnabled + TruthValue + } + + ospfv3AreaId OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A 32-bit unsigned integer uniquely identifying an area. + Area ID 0 is used for the OSPFv3 backbone." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3AreaEntry 1 } + + ospfv3AreaImportAsExtern OBJECT-TYPE + SYNTAX INTEGER { + importExternal(1), -- normal area + importNoExternal(2), -- stub area + importNssa(3) -- not-so-stubby-area + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether an area is a stub area, NSSA, or + standard area. AS-scope LSAs are not imported into stub + areas or NSSAs. NSSAs import AS-External data as NSSA + LSAs that have Area-scope." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + DEFVAL { importExternal } + ::= { ospfv3AreaEntry 2 } + + ospfv3AreaSpfRuns OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times that the intra-area route + table has been calculated using this area's + link state database. This is typically done + using Dijkstra's algorithm. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3AreaEntry 3 } + + ospfv3AreaBdrRtrCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of area border routers + reachable within this area. This is initially zero, + and is calculated in each Shortest Path First (SPF) + pass." + DEFVAL { 0 } + ::= { ospfv3AreaEntry 4 } + + ospfv3AreaAsBdrRtrCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of Autonomous System border + routers reachable within this area. This is + initially zero, and is calculated in each SPF + pass." + DEFVAL { 0 } + ::= { ospfv3AreaEntry 5 } + + ospfv3AreaScopeLsaCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of Area-scope link state + advertisements in this area's link state + database." + DEFVAL { 0 } + ::= { ospfv3AreaEntry 6 } + + ospfv3AreaScopeLsaCksumSum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 32-bit unsigned sum of the Area-scope link state + advertisements' LS checksums contained in this + area's link state database. The sum can be used + to determine if there has been a change in a + router's link state database or to compare the + link state database of two routers." + ::= { ospfv3AreaEntry 7 } + + ospfv3AreaSummary OBJECT-TYPE + SYNTAX INTEGER { + noAreaSummary(1), + sendAreaSummary(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The variable ospfv3AreaSummary controls the + import of Inter-Area LSAs into stub and + NSSA areas. It has no effect on other areas. + + If it is noAreaSummary, the router will neither + originate nor propagate Inter-Area LSAs into the + stub or NSSA area. It will only advertise a + default route. + + If it is sendAreaSummary, the router will both + summarize and propagate Inter-Area LSAs." + DEFVAL { sendAreaSummary } + ::= { ospfv3AreaEntry 8 } + + ospfv3AreaRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3AreaEntry 9 } + + ospfv3AreaStubMetric OBJECT-TYPE + SYNTAX BigMetric + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The metric value advertised for the default route + into stub and NSSA areas. By default, this equals the + least metric among the interfaces to other areas." + ::= { ospfv3AreaEntry 10 } + + ospfv3AreaNssaTranslatorRole OBJECT-TYPE + SYNTAX INTEGER { always(1), candidate(2) } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates an NSSA border router's policy to + perform NSSA translation of NSSA-LSAs into + AS-External-LSAs." + DEFVAL { candidate } + ::= { ospfv3AreaEntry 11 } + + ospfv3AreaNssaTranslatorState OBJECT-TYPE + SYNTAX INTEGER { + enabled(1), + elected(2), + disabled(3) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates if and how an NSSA border router is + performing NSSA translation of NSSA-LSAs into + AS-External-LSAs. When this object is set to + 'enabled', the NSSA border router's + ospfv3AreaNssaTranslatorRole has been set to 'always'. + When this object is set to 'elected', a candidate + NSSA border router is translating NSSA-LSAs into + AS-External-LSAs. When this object is set to + 'disabled', a candidate NSSA Border router is NOT + translating NSSA-LSAs into AS-External-LSAs." + ::= { ospfv3AreaEntry 12 } + + ospfv3AreaNssaTranslatorStabInterval OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The stability interval defined as the number of + seconds after an elected translator determines its + services are no longer required that it should + continue to perform its translation duties." + DEFVAL { 40 } + ::= { ospfv3AreaEntry 13 } + + ospfv3AreaNssaTranslatorEvents OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates the number of Translator state changes + that have occurred since the last start-up of the + OSPFv3 routing process. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3AreaEntry 14 } + + ospfv3AreaStubMetricType OBJECT-TYPE + SYNTAX INTEGER { + ospfv3Metric(1), -- OSPF Metric + comparableCost(2), -- external type 1 + nonComparable(3) -- external type 2 + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This variable assigns the type of metric + advertised as a default route." + DEFVAL { ospfv3Metric } + ::= { ospfv3AreaEntry 15 } + + ospfv3AreaTEEnabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether or not traffic engineering + is enabled in the area. The object is set + to the value true (1) to enable traffic engineering. + Traffic engineering is disabled by default." + DEFVAL { false } + ::= { ospfv3AreaEntry 16 } + + -- OSPFv3 AS-Scope Link State Database + + ospfv3AsLsdbTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3AsLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Process's AS-scope link state database + (LSDB). The LSDB contains the AS-scope link state + advertisements from throughout the areas that the + device is attached to." + ::= { ospfv3Objects 3 } + + ospfv3AsLsdbEntry OBJECT-TYPE + SYNTAX Ospfv3AsLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single AS-scope link state advertisement." + INDEX { ospfv3AsLsdbType, + ospfv3AsLsdbRouterId, + ospfv3AsLsdbLsid } + ::= { ospfv3AsLsdbTable 1 } + + Ospfv3AsLsdbEntry ::= SEQUENCE { + ospfv3AsLsdbType + Unsigned32, + ospfv3AsLsdbRouterId + Ospfv3RouterIdTC, + ospfv3AsLsdbLsid + Ospfv3LsIdTC, + ospfv3AsLsdbSequence + Ospfv3LsaSequenceTC, + ospfv3AsLsdbAge + Ospfv3LsaAgeTC, + ospfv3AsLsdbChecksum + Integer32, + ospfv3AsLsdbAdvertisement + OCTET STRING, + ospfv3AsLsdbTypeKnown + TruthValue + } + + ospfv3AsLsdbType OBJECT-TYPE + SYNTAX Unsigned32(0..'FFFFFFFF'h) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The type of the link state advertisement. + Each link state type has a separate + advertisement format. AS-scope LSAs not recognized + by the router may be stored in the database." + ::= { ospfv3AsLsdbEntry 1 } + + ospfv3AsLsdbRouterId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The 32-bit number that uniquely identifies the + originating router in the Autonomous System." + REFERENCE + "OSPF Version 2, Appendix C.1, Global parameters" + ::= { ospfv3AsLsdbEntry 2 } + + ospfv3AsLsdbLsid OBJECT-TYPE + SYNTAX Ospfv3LsIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Link State ID is an LS type-specific field + containing a unique identifier; + it identifies the piece of the routing domain + that is being described by the advertisement. + In contrast to OSPFv2, the LSID has no + addressing semantics." + ::= { ospfv3AsLsdbEntry 3 } + + -- Note that the OSPF sequence number is a 32-bit signed + -- integer. It starts with the value '80000001'h + -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. + -- Thus, a typical sequence number will be very negative. + + ospfv3AsLsdbSequence OBJECT-TYPE + SYNTAX Ospfv3LsaSequenceTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The sequence number field is a signed 32-bit + integer. It is used to detect old and duplicate + link state advertisements. The space of + sequence numbers is linearly ordered. The + larger the sequence number, the more recent the + advertisement." + REFERENCE + "OSPF Version 2, Section 12.1.6, LS sequence + number" + ::= { ospfv3AsLsdbEntry 4 } + + ospfv3AsLsdbAge OBJECT-TYPE + SYNTAX Ospfv3LsaAgeTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the age of the link state + advertisement in seconds. The high-order bit + of the LS age field is considered the DoNotAge + bit for support of on-demand circuits." + REFERENCE + "OSPF Version 2, Section 12.1.1, LS age; + Extending OSPF to Support Demand Circuits, + Section 2.2, The LS age field." + ::= { ospfv3AsLsdbEntry 5 } + + ospfv3AsLsdbChecksum OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the checksum of the complete + contents of the advertisement, excepting the + age field. The age field is excepted so that + an advertisement's age can be incremented + without updating the checksum. The checksum + used is the same that is used for ISO + connectionless datagrams; it is commonly + referred to as the Fletcher checksum." + REFERENCE + "OSPF Version 2, Section 12.1.7, LS checksum" + ::= { ospfv3AsLsdbEntry 6 } + + ospfv3AsLsdbAdvertisement OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (1..65535)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The entire link state advertisement, including + its header." + ::= { ospfv3AsLsdbEntry 7 } + + ospfv3AsLsdbTypeKnown OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value true (1) indicates that the LSA type + is recognized by this router." + ::= { ospfv3AsLsdbEntry 8 } + + -- OSPFv3 Area-Scope Link State Database + + ospfv3AreaLsdbTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3AreaLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Process's Area-scope LSDB. + The LSDB contains the Area-scope link state + advertisements from throughout the area that the + device is attached to." + ::= { ospfv3Objects 4 } + + ospfv3AreaLsdbEntry OBJECT-TYPE + SYNTAX Ospfv3AreaLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single Area-scope link state advertisement." + INDEX { ospfv3AreaLsdbAreaId, + ospfv3AreaLsdbType, + ospfv3AreaLsdbRouterId, + ospfv3AreaLsdbLsid } + ::= { ospfv3AreaLsdbTable 1 } + + Ospfv3AreaLsdbEntry ::= SEQUENCE { + ospfv3AreaLsdbAreaId + Ospfv3AreaIdTC, + ospfv3AreaLsdbType + Unsigned32, + ospfv3AreaLsdbRouterId + Ospfv3RouterIdTC, + ospfv3AreaLsdbLsid + Ospfv3LsIdTC, + ospfv3AreaLsdbSequence + Ospfv3LsaSequenceTC, + ospfv3AreaLsdbAge + Ospfv3LsaAgeTC, + ospfv3AreaLsdbChecksum + Integer32, + ospfv3AreaLsdbAdvertisement + OCTET STRING, + ospfv3AreaLsdbTypeKnown + TruthValue + } + + ospfv3AreaLsdbAreaId OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The 32-bit identifier of the Area from which the + LSA was received." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3AreaLsdbEntry 1 } + + ospfv3AreaLsdbType OBJECT-TYPE + SYNTAX Unsigned32(0..'FFFFFFFF'h) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The type of the link state advertisement. + Each link state type has a separate + advertisement format. Area-scope LSAs unrecognized + by the router are also stored in this database." + ::= { ospfv3AreaLsdbEntry 2 } + + ospfv3AreaLsdbRouterId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The 32-bit number that uniquely identifies the + originating router in the Autonomous System." + REFERENCE + "OSPF Version 2, Appendix C.1, Global parameters" + ::= { ospfv3AreaLsdbEntry 3 } + + ospfv3AreaLsdbLsid OBJECT-TYPE + SYNTAX Ospfv3LsIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Link State ID is an LS type-specific field + containing a unique identifier; + it identifies the piece of the routing domain + that is being described by the advertisement. + In contrast to OSPFv2, the LSID has no + addressing semantics." + ::= { ospfv3AreaLsdbEntry 4 } + + -- Note that the OSPF sequence number is a 32-bit signed + -- integer. It starts with the value '80000001'h + -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. + -- Thus, a typical sequence number will be very negative. + + ospfv3AreaLsdbSequence OBJECT-TYPE + SYNTAX Ospfv3LsaSequenceTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The sequence number field is a signed 32-bit + integer. It is used to detect old and + duplicate link state advertisements. The space + of sequence numbers is linearly ordered. The + larger the sequence number, the more recent the + advertisement." + REFERENCE + "OSPF Version 2, Section 12.1.6, LS sequence + number" + ::= { ospfv3AreaLsdbEntry 5 } + + ospfv3AreaLsdbAge OBJECT-TYPE + SYNTAX Ospfv3LsaAgeTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the age of the link state + advertisement in seconds. The high-order bit + of the LS age field is considered the DoNotAge + bit for support of on-demand circuits." + REFERENCE + "OSPF Version 2, Section 12.1.1, LS age; + Extending OSPF to Support Demand Circuits, + Section 2.2, The LS age field." + ::= { ospfv3AreaLsdbEntry 6 } + + ospfv3AreaLsdbChecksum OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the checksum of the complete + contents of the advertisement, excepting the + age field. The age field is excepted so that + an advertisement's age can be incremented + without updating the checksum. The checksum + used is the same that is used for ISO + connectionless datagrams; it is commonly + referred to as the Fletcher checksum." + REFERENCE + "OSPF Version 2, Section 12.1.7, LS checksum" + ::= { ospfv3AreaLsdbEntry 7 } + + ospfv3AreaLsdbAdvertisement OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (1..65535)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The entire link state advertisement, including + its header." + ::= { ospfv3AreaLsdbEntry 8 } + + ospfv3AreaLsdbTypeKnown OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value true (1) indicates that the LSA type is + recognized by this router." + ::= { ospfv3AreaLsdbEntry 9 } + + -- OSPFv3 Link-Scope Link State Database, for non-virtual interfaces + + ospfv3LinkLsdbTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3LinkLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Process's Link-scope LSDB for non-virtual + interfaces. The LSDB contains the Link-scope link + state advertisements from the interfaces that the + device is attached to." + ::= { ospfv3Objects 5 } + + ospfv3LinkLsdbEntry OBJECT-TYPE + SYNTAX Ospfv3LinkLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single Link-scope link state advertisement." + INDEX { ospfv3LinkLsdbIfIndex, + ospfv3LinkLsdbIfInstId, + ospfv3LinkLsdbType, + ospfv3LinkLsdbRouterId, + ospfv3LinkLsdbLsid } + ::= { ospfv3LinkLsdbTable 1 } + + Ospfv3LinkLsdbEntry ::= SEQUENCE { + ospfv3LinkLsdbIfIndex + InterfaceIndex, + ospfv3LinkLsdbIfInstId + Ospfv3IfInstIdTC, + ospfv3LinkLsdbType + Unsigned32, + ospfv3LinkLsdbRouterId + Ospfv3RouterIdTC, + ospfv3LinkLsdbLsid + Ospfv3LsIdTC, + ospfv3LinkLsdbSequence + Ospfv3LsaSequenceTC, + ospfv3LinkLsdbAge + Ospfv3LsaAgeTC, + ospfv3LinkLsdbChecksum + Integer32, + ospfv3LinkLsdbAdvertisement + OCTET STRING, + ospfv3LinkLsdbTypeKnown + TruthValue + } + + ospfv3LinkLsdbIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The identifier of the link from which the LSA + was received." + ::= { ospfv3LinkLsdbEntry 1 } + + ospfv3LinkLsdbIfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The identifier of the interface instance from + which the LSA was received." + ::= { ospfv3LinkLsdbEntry 2 } + + ospfv3LinkLsdbType OBJECT-TYPE + SYNTAX Unsigned32(0..'FFFFFFFF'h) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The type of the link state advertisement. + Each link state type has a separate + advertisement format. Link-scope LSAs unrecognized + by the router are also stored in this database." + ::= { ospfv3LinkLsdbEntry 3 } + + ospfv3LinkLsdbRouterId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The 32-bit number that uniquely identifies the + originating router in the Autonomous System." + REFERENCE + "OSPF Version 2, Appendix C.1, Global parameters" + ::= { ospfv3LinkLsdbEntry 4 } + + ospfv3LinkLsdbLsid OBJECT-TYPE + SYNTAX Ospfv3LsIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Link State ID is an LS type-specific field + containing a unique identifier; + it identifies the piece of the routing domain + that is being described by the advertisement. + In contrast to OSPFv2, the LSID has no + addressing semantics. However, in OSPFv3 + the Link State ID always contains the flooding + scope of the LSA." + ::= { ospfv3LinkLsdbEntry 5 } + + -- Note that the OSPF sequence number is a 32-bit signed + -- integer. It starts with the value '80000001'h + -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. + -- Thus, a typical sequence number will be very negative. + + ospfv3LinkLsdbSequence OBJECT-TYPE + SYNTAX Ospfv3LsaSequenceTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The sequence number field is a signed 32-bit + integer. It is used to detect old and duplicate + link state advertisements. The space of + sequence numbers is linearly ordered. The + larger the sequence number, the more recent the + advertisement." + REFERENCE + "OSPF Version 2, Section 12.1.6, LS sequence + number" + ::= { ospfv3LinkLsdbEntry 6 } + + ospfv3LinkLsdbAge OBJECT-TYPE + SYNTAX Ospfv3LsaAgeTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the age of the link state + advertisement in seconds. The high-order bit + of the LS age field is considered the DoNotAge + bit for support of on-demand circuits." + REFERENCE + "OSPF Version 2, Section 12.1.1, LS age; + Extending OSPF to Support Demand Circuits, + Section 2.2, The LS age field." + ::= { ospfv3LinkLsdbEntry 7 } + + ospfv3LinkLsdbChecksum OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the checksum of the complete + contents of the advertisement, excepting the + age field. The age field is excepted so that + an advertisement's age can be incremented + without updating the checksum. The checksum + used is the same that is used for ISO + connectionless datagrams; it is commonly + referred to as the Fletcher checksum." + REFERENCE + "OSPF Version 2, Section 12.1.7, LS checksum" + ::= { ospfv3LinkLsdbEntry 8 } + + ospfv3LinkLsdbAdvertisement OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (1..65535)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The entire link state advertisement, including + its header." + ::= { ospfv3LinkLsdbEntry 9 } + + ospfv3LinkLsdbTypeKnown OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value true (1) indicates that the LSA type is + recognized by this router." + ::= { ospfv3LinkLsdbEntry 10 } + + -- OSPF Host Table + + ospfv3HostTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3HostEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Host/Metric Table indicates what hosts are + directly attached to the router and their + corresponding metrics." + REFERENCE + "OSPF Version 2, Appendix C.7, Host route + parameters" + ::= { ospfv3Objects 6 } + + ospfv3HostEntry OBJECT-TYPE + SYNTAX Ospfv3HostEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A metric to be advertised when a given host is + reachable. + + The information in this table is persistent, and + when written, the entity SHOULD save the change + to non-volatile storage." + INDEX { ospfv3HostAddressType, + ospfv3HostAddress } + ::= { ospfv3HostTable 1 } + + Ospfv3HostEntry ::= SEQUENCE { + ospfv3HostAddressType + InetAddressType, + ospfv3HostAddress + InetAddress, + ospfv3HostMetric + Metric, + ospfv3HostRowStatus + RowStatus, + ospfv3HostAreaID + Ospfv3AreaIdTC + } + + ospfv3HostAddressType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The address type of ospfv3HostAddress. Only IPv6 + global address type is expected." + REFERENCE + "OSPF Version 2, Appendix C.7, Host route + parameters" + ::= { ospfv3HostEntry 1 } + + ospfv3HostAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IPv6 address of the host. Must be an + IPv6 global address." + REFERENCE + "OSPF Version 2, Appendix C.7, Host route + parameters" + ::= { ospfv3HostEntry 2 } + + ospfv3HostMetric OBJECT-TYPE + SYNTAX Metric + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The metric to be advertised." + REFERENCE + "OSPF Version 2, Appendix C.7, Host route + parameters" + ::= { ospfv3HostEntry 3 } + + ospfv3HostRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3HostEntry 4 } + + ospfv3HostAreaID OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The Area the host entry is to be found within. + By default, the area for the subsuming OSPFv3 + interface, or Area 0 if there is no subsuming + interface." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3HostEntry 5 } + + -- OSPFv3 Interface Table + + ospfv3IfTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3IfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Interface Table describes the + interfaces from the viewpoint of OSPFv3." + REFERENCE + "OSPF for IPv6, Appendix C.3, Router Interface + Parameters" + ::= { ospfv3Objects 7 } + + ospfv3IfEntry OBJECT-TYPE + SYNTAX Ospfv3IfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Interface Entry describes one + interface from the viewpoint of OSPFv3. + + The information in this table is persistent, + and when written, the entity SHOULD save the + change to non-volatile storage." + INDEX { ospfv3IfIndex, + ospfv3IfInstId } + ::= { ospfv3IfTable 1 } + + Ospfv3IfEntry ::= SEQUENCE { + ospfv3IfIndex + InterfaceIndex, + ospfv3IfInstId + Ospfv3IfInstIdTC, + ospfv3IfAreaId + Ospfv3AreaIdTC, + ospfv3IfType + INTEGER, + ospfv3IfAdminStatus + Status, + ospfv3IfRtrPriority + DesignatedRouterPriority, + ospfv3IfTransitDelay + Ospfv3UpToRefreshIntervalTC, + ospfv3IfRetransInterval + Ospfv3UpToRefreshIntervalTC, + ospfv3IfHelloInterval + HelloRange, + ospfv3IfRtrDeadInterval + Ospfv3DeadIntervalRangeTC, + ospfv3IfPollInterval + Unsigned32, + ospfv3IfState + INTEGER, + ospfv3IfDesignatedRouter + Ospfv3RouterIdTC, + ospfv3IfBackupDesignatedRouter + Ospfv3RouterIdTC, + ospfv3IfEvents + Counter32, + ospfv3IfRowStatus + RowStatus, + ospfv3IfDemand + TruthValue, + ospfv3IfMetricValue + Metric, + ospfv3IfLinkScopeLsaCount + Gauge32, + ospfv3IfLinkLsaCksumSum + Unsigned32, + ospfv3IfDemandNbrProbe + TruthValue, + ospfv3IfDemandNbrProbeRetransLimit + Unsigned32, + ospfv3IfDemandNbrProbeInterval + Unsigned32, + ospfv3IfTEDisabled + TruthValue, + ospfv3IfLinkLSASuppression + TruthValue + } + + ospfv3IfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The interface index of this OSPFv3 interface. + It corresponds to the interface index of the + IPv6 interface on which OSPFv3 is configured." + ::= { ospfv3IfEntry 1 } + + ospfv3IfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Enables multiple interface instances of OSPFv3 + to be run over a single link. Each interface + instance would be assigned a separate ID. This ID + has local link significance only." + ::= { ospfv3IfEntry 2 } + + ospfv3IfAreaId OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "A 32-bit integer uniquely identifying the area + to which the interface connects. Area ID + 0 is used for the OSPFv3 backbone." + DEFVAL { 0 } + ::= { ospfv3IfEntry 3 } + + ospfv3IfType OBJECT-TYPE + SYNTAX INTEGER { + broadcast(1), + nbma(2), + pointToPoint(3), + pointToMultipoint(5) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The OSPFv3 interface type." + ::= { ospfv3IfEntry 4 } + + ospfv3IfAdminStatus OBJECT-TYPE + SYNTAX Status + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The OSPFv3 interface's administrative status. + The value formed on the interface; the interface + will be advertised as an internal route to some + area. The value 'disabled' denotes that the + interface is external to OSPFv3. + + Note that a value of 'disabled' for the object + ospfv3AdminStatus will override a value of + 'enabled' for the interface." + DEFVAL { enabled } + ::= { ospfv3IfEntry 5 } + + ospfv3IfRtrPriority OBJECT-TYPE + SYNTAX DesignatedRouterPriority + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The priority of this interface. Used in + multi-access networks, this field is used in + the designated-router election algorithm. The + value 0 signifies that the router is not + eligible to become the Designated Router on this + particular network. In the event of a tie in + this value, routers will use their Router ID as + a tie breaker." + DEFVAL { 1 } + ::= { ospfv3IfEntry 6 } + + ospfv3IfTransitDelay OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The estimated number of seconds it takes to transmit + a Link State Update packet over this interface. LSAs + contained in the update packet must have their age + incremented by this amount before transmission. This + value should take into account the transmission and + propagation delays of the interface." + REFERENCE + "OSPF for IPv6, Appendix C.3, Router Interface + Parameters." + DEFVAL { 1 } + ::= { ospfv3IfEntry 7 } + + ospfv3IfRetransInterval OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The number of seconds between link state + advertisement retransmissions for adjacencies + + belonging to this interface. This value is + also used when retransmitting database + description and Link State Request packets." + DEFVAL { 5 } + ::= { ospfv3IfEntry 8 } + + ospfv3IfHelloInterval OBJECT-TYPE + SYNTAX HelloRange + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The length of time, in seconds, between the + Hello packets that the router sends on the + interface. This value must be the same for all + routers attached to a common network." + DEFVAL { 10 } + ::= { ospfv3IfEntry 9 } + + ospfv3IfRtrDeadInterval OBJECT-TYPE + SYNTAX Ospfv3DeadIntervalRangeTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The number of seconds that a router's Hello + packets have not been seen before its + neighbors declare the router down on the interface. + This should be some multiple of the Hello interval. + This value must be the same for all routers attached + to a common network." + DEFVAL { 40 } + ::= { ospfv3IfEntry 10 } + + ospfv3IfPollInterval OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The larger time interval, in seconds, between + the Hello packets sent to an inactive, + non-broadcast multi-access neighbor." + DEFVAL { 120 } + ::= { ospfv3IfEntry 11 } + + ospfv3IfState OBJECT-TYPE + SYNTAX INTEGER { + down(1), + loopback(2), + waiting(3), + pointToPoint(4), + designatedRouter(5), + backupDesignatedRouter(6), + otherDesignatedRouter(7), + standby(8) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The OSPFv3 interface state. An interface may be + in standby state if there are multiple interfaces + on the link and another interface is active. The + interface may be in Down state if the underlying + IPv6 interface is down or if the admin status is + 'disabled' either globally or for the interface." + ::= { ospfv3IfEntry 12 } + + ospfv3IfDesignatedRouter OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Router ID of the Designated Router." + ::= { ospfv3IfEntry 13 } + + ospfv3IfBackupDesignatedRouter OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Router ID of the Backup Designated + Router." + ::= { ospfv3IfEntry 14 } + + ospfv3IfEvents OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times this OSPFv3 interface has + changed its state or an error has occurred. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3IfEntry 15 } + + ospfv3IfRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3IfEntry 16 } + + ospfv3IfDemand OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether Demand OSPFv3 procedures + (Hello suppression to FULL neighbors and + setting the DoNotAge flag on propagated LSAs) + should be performed on this interface." + DEFVAL { false } + ::= { ospfv3IfEntry 17 } + + ospfv3IfMetricValue OBJECT-TYPE + SYNTAX Metric + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The metric assigned to this interface. + The default value of the metric is + 'Reference Bandwidth / ifSpeed'. The value + of the reference bandwidth can be set + in the ospfv3ReferenceBandwidth object." + ::= { ospfv3IfEntry 18 } + + ospfv3IfLinkScopeLsaCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of Link-scope link state + advertisements in this link's link state + database." + ::= { ospfv3IfEntry 19 } + + ospfv3IfLinkLsaCksumSum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 32-bit unsigned sum of the Link-scope link state + advertisements' LS checksums contained in this + link's link state database. The sum can be used + to determine if there has been a change in a + router's link state database or to compare the + link state database of two routers." + ::= { ospfv3IfEntry 20 } + + ospfv3IfDemandNbrProbe OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether or not neighbor probing is + enabled to determine whether or not the neighbor + is inactive. Neighbor probing is disabled by + default." + DEFVAL { false } + ::= { ospfv3IfEntry 21 } + +ospfv3IfDemandNbrProbeRetransLimit OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The number of consecutive LSA retransmissions before + the neighbor is deemed inactive and the neighbor + adjacency is brought down." + DEFVAL { 10 } + ::= { ospfv3IfEntry 22} + +ospfv3IfDemandNbrProbeInterval OBJECT-TYPE + SYNTAX Unsigned32 + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Defines how often the neighbor will be probed." + DEFVAL { 120 } + ::= { ospfv3IfEntry 23 } + + ospfv3IfTEDisabled OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Indicates whether or not traffic engineering + is disabled on the interface when traffic + engineering is enabled in the area where the + interface is attached. The object is set + to the value true (1) to disable traffic engineering + on the interface. Traffic engineering is enabled + by default on the interface when traffic engineering + is enabled in the area where the interface is + attached." + DEFVAL { false } + ::= { ospfv3IfEntry 24 } + + ospfv3IfLinkLSASuppression OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Specifies whether or not link LSA origination is + suppressed for broadcast or NBMA interface types. + The object is set to value true (1) to suppress + the origination." + REFERENCE + "OSPF for IPv6, Appendix C.3, Router Interface + Parameters" + DEFVAL { false } + ::= { ospfv3IfEntry 25 } + + -- OSPFv3 Virtual Interface Table + + ospfv3VirtIfTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3VirtIfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about this router's virtual + interfaces that the OSPFv3 Process is configured + to carry on." + REFERENCE + "OSPF for IPv6, Appendix C.4, Virtual Link + Parameters" + ::= { ospfv3Objects 8 } + + ospfv3VirtIfEntry OBJECT-TYPE + SYNTAX Ospfv3VirtIfEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Information about a single virtual interface. + + The information in this table is persistent, + and when written, the entity SHOULD save the + change to non-volatile storage." + INDEX { ospfv3VirtIfAreaId, + ospfv3VirtIfNeighbor } + ::= { ospfv3VirtIfTable 1 } + + Ospfv3VirtIfEntry ::= SEQUENCE { + ospfv3VirtIfAreaId + Ospfv3AreaIdTC, + ospfv3VirtIfNeighbor + Ospfv3RouterIdTC, + ospfv3VirtIfIndex + InterfaceIndex, + ospfv3VirtIfInstId + Ospfv3IfInstIdTC, + ospfv3VirtIfTransitDelay + Ospfv3UpToRefreshIntervalTC, + ospfv3VirtIfRetransInterval + Ospfv3UpToRefreshIntervalTC, + ospfv3VirtIfHelloInterval + HelloRange, + ospfv3VirtIfRtrDeadInterval + Ospfv3DeadIntervalRangeTC, + ospfv3VirtIfState + INTEGER, + ospfv3VirtIfEvents + Counter32, + ospfv3VirtIfRowStatus + RowStatus, + ospfv3VirtIfLinkScopeLsaCount + Gauge32, + ospfv3VirtIfLinkLsaCksumSum + Unsigned32 + } + + ospfv3VirtIfAreaId OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The transit area that the virtual link + traverses. By definition, this is not + Area 0." + ::= { ospfv3VirtIfEntry 1 } + + ospfv3VirtIfNeighbor OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Router ID of the virtual neighbor." + ::= { ospfv3VirtIfEntry 2 } + + ospfv3VirtIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The local interface index assigned by the + OSPFv3 Process to this OSPFv3 virtual interface. + It is advertised in Hellos sent over the virtual + link and in the router's router-LSAs." + ::= { ospfv3VirtIfEntry 3 } + + ospfv3VirtIfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The local Interface Instance ID assigned by the + OSPFv3 Process to this OSPFv3 virtual interface." + ::= { ospfv3VirtIfEntry 4 } + + ospfv3VirtIfTransitDelay OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The estimated number of seconds it takes to + transmit a Link State Update packet over this + interface." + DEFVAL { 1 } + ::= { ospfv3VirtIfEntry 5 } + + ospfv3VirtIfRetransInterval OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The number of seconds between link state + advertisement retransmissions for adjacencies + belonging to this interface. This value is + also used when retransmitting database + description and Link State Request packets. This + value should be well over the expected + round-trip time." + DEFVAL { 5 } + ::= { ospfv3VirtIfEntry 6 } + + ospfv3VirtIfHelloInterval OBJECT-TYPE + SYNTAX HelloRange + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The length of time, in seconds, between the + Hello packets that the router sends on the + interface. This value must be the same for the + virtual neighbor." + DEFVAL { 10 } + ::= { ospfv3VirtIfEntry 7 } + + ospfv3VirtIfRtrDeadInterval OBJECT-TYPE + SYNTAX Ospfv3DeadIntervalRangeTC + UNITS "seconds" + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The number of seconds that a router's Hello + packets have not been seen before its + neighbors declare the router down. This should + be some multiple of the Hello interval. This + value must be the same for the virtual + neighbor." + DEFVAL { 60 } + ::= { ospfv3VirtIfEntry 8 } + + ospfv3VirtIfState OBJECT-TYPE + SYNTAX INTEGER { + down(1), + pointToPoint(4) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "OSPF virtual interface states. The same encoding + as the ospfV3IfTable is used." + ::= { ospfv3VirtIfEntry 9 } + + ospfv3VirtIfEvents OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of state changes or error events on + this virtual link. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3VirtIfEntry 10 } + + ospfv3VirtIfRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3VirtIfEntry 11 } + + ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The total number of Link-scope link state + advertisements in this virtual link's link state + database." + ::= { ospfv3VirtIfEntry 12 } + + ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The 32-bit unsigned sum of the Link-scope link state + advertisements' LS checksums contained in this + virtual link's link state database. The sum can be used + to determine if there has been a change in a + router's link state database or to compare the + link state database of two routers." + ::= { ospfv3VirtIfEntry 13 } + + -- OSPFv3 Neighbor Table + + ospfv3NbrTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3NbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table describing all neighbors in the + locality of the OSPFv3 router." + REFERENCE + "OSPF Version 2, Section 10, The Neighbor Data + Structure" + ::= { ospfv3Objects 9 } + + ospfv3NbrEntry OBJECT-TYPE + SYNTAX Ospfv3NbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The information regarding a single neighbor." + REFERENCE + "OSPF Version 2, Section 10, The Neighbor Data + Structure" + INDEX { ospfv3NbrIfIndex, + ospfv3NbrIfInstId, + ospfv3NbrRtrId } + ::= { ospfv3NbrTable 1 } + + Ospfv3NbrEntry ::= SEQUENCE { + ospfv3NbrIfIndex + InterfaceIndex, + ospfv3NbrIfInstId + Ospfv3IfInstIdTC, + ospfv3NbrRtrId + Ospfv3RouterIdTC, + ospfv3NbrAddressType + InetAddressType, + ospfv3NbrAddress + InetAddress, + ospfv3NbrOptions + Integer32, + ospfv3NbrPriority + DesignatedRouterPriority, + ospfv3NbrState + INTEGER, + ospfv3NbrEvents + Counter32, + ospfv3NbrLsRetransQLen + Gauge32, + ospfv3NbrHelloSuppressed + TruthValue, + ospfv3NbrIfId + InterfaceIndex, + ospfv3NbrRestartHelperStatus + INTEGER, + ospfv3NbrRestartHelperAge + Ospfv3UpToRefreshIntervalTC, + ospfv3NbrRestartHelperExitReason + INTEGER + } + + ospfv3NbrIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Local Link ID of the link over which the + neighbor can be reached." + ::= { ospfv3NbrEntry 1 } + + ospfv3NbrIfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Interface instance over which the neighbor + can be reached. This ID has local link + significance only." + ::= { ospfv3NbrEntry 2 } + + ospfv3NbrRtrId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A 32-bit unsigned integer uniquely identifying the + neighboring router in the Autonomous System." + ::= { ospfv3NbrEntry 3 } + + ospfv3NbrAddressType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The address type of ospfv3NbrAddress. Only IPv6 + addresses without zone index are expected." + ::= { ospfv3NbrEntry 4 } + + ospfv3NbrAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IPv6 address of the neighbor associated with + the local link." + ::= { ospfv3NbrEntry 5 } + + ospfv3NbrOptions OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A bit mask corresponding to the neighbor's + options field." + REFERENCE + "OSPF for IPv6, Appendix A.2, The Options Field" + ::= { ospfv3NbrEntry 6 } + + ospfv3NbrPriority OBJECT-TYPE + SYNTAX DesignatedRouterPriority + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The priority of this neighbor in the designated- + router election algorithm. The value 0 signifies + that the neighbor is not eligible to become the + Designated Router on this particular network." + ::= { ospfv3NbrEntry 7 } + + ospfv3NbrState OBJECT-TYPE + SYNTAX INTEGER { + down(1), + attempt(2), + init(3), + twoWay(4), + exchangeStart(5), + exchange(6), + loading(7), + full(8) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The state of the relationship with this + neighbor." + REFERENCE + "OSPF Version 2, Section 10.1, Neighbor states" + ::= { ospfv3NbrEntry 8 } + + ospfv3NbrEvents OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times this neighbor relationship + has changed state or an error has occurred. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3NbrEntry 9 } + + ospfv3NbrLsRetransQLen OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current length of the retransmission + queue." + ::= { ospfv3NbrEntry 10 } + + ospfv3NbrHelloSuppressed OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates whether Hellos are being suppressed + to the neighbor." + ::= { ospfv3NbrEntry 11 } + + ospfv3NbrIfId OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Interface ID that the neighbor advertises + in its Hello packets on this link, that is, the + neighbor's local interface index." + ::= { ospfv3NbrEntry 12 } + + ospfv3NbrRestartHelperStatus OBJECT-TYPE + SYNTAX INTEGER { notHelping(1), + helping(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates whether the router is acting + as a graceful restart helper for the neighbor." + ::= { ospfv3NbrEntry 13 } + + ospfv3NbrRestartHelperAge OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Remaining time in current OSPF graceful restart + interval, if the router is acting as a restart + helper for the neighbor." + ::= { ospfv3NbrEntry 14 } + + ospfv3NbrRestartHelperExitReason OBJECT-TYPE + SYNTAX INTEGER { none(1), + inProgress(2), + completed(3), + timedOut(4), + topologyChanged(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Describes the outcome of the last attempt at acting + as a graceful restart helper for the neighbor. + + none: no restart has yet been attempted. + inProgress: a restart attempt is currently underway. + completed: the last restart completed successfully. + timedOut: the last restart timed out. + topologyChanged: the last restart was aborted due to + a topology change." + ::= { ospfv3NbrEntry 15 } + + -- OSPFv3 Configured Neighbor Table + + ospfv3CfgNbrTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3CfgNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table describing all configured neighbors. + + The Configured Neighbors table just gives + OSPFv3 information for sending OSPFv3 packets + to potential neighbors and is typically used + on NBMA and Point-to-Multipoint networks. + Once a Hello is received from a neighbor in + the Configured Neighbor table, an entry for + that neighbor is created in the Neighbor table + and adjacency state is maintained there. + Neighbors on multi-access or Point-to-Point + networks can use multicast addressing, so only + Neighbor table entries are created for them." + REFERENCE + "OSPF Version 2, Section 10, The Neighbor Data + Structure" + ::= { ospfv3Objects 10 } + + ospfv3CfgNbrEntry OBJECT-TYPE + SYNTAX Ospfv3CfgNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The information regarding a single configured + neighbor. + + The information in this table is persistent, + and when written, the entity SHOULD save the + change to non-volatile storage." + REFERENCE + "OSPF Version 2, Section 10, The Neighbor Data + Structure" + INDEX { ospfv3CfgNbrIfIndex, + ospfv3CfgNbrIfInstId, + ospfv3CfgNbrAddressType, + ospfv3CfgNbrAddress } + ::= { ospfv3CfgNbrTable 1 } + + Ospfv3CfgNbrEntry ::= SEQUENCE { + ospfv3CfgNbrIfIndex + InterfaceIndex, + ospfv3CfgNbrIfInstId + Ospfv3IfInstIdTC, + ospfv3CfgNbrAddressType + InetAddressType, + ospfv3CfgNbrAddress + InetAddress, + ospfv3CfgNbrPriority + DesignatedRouterPriority, + ospfv3CfgNbrRowStatus + RowStatus + } + + ospfv3CfgNbrIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Local Link ID of the link over which the + neighbor can be reached." + ::= { ospfv3CfgNbrEntry 1 } + + ospfv3CfgNbrIfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Interface instance over which the neighbor + can be reached. This ID has local link + significance only." + ::= { ospfv3CfgNbrEntry 2 } + + ospfv3CfgNbrAddressType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The address type of ospfv3NbrAddress. Only IPv6 + addresses without zone index are expected." + ::= { ospfv3CfgNbrEntry 3 } + + ospfv3CfgNbrAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IPv6 address of the neighbor associated with + the local link." + ::= { ospfv3CfgNbrEntry 4 } + + ospfv3CfgNbrPriority OBJECT-TYPE + SYNTAX DesignatedRouterPriority + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "The priority of this neighbor in the designated- + router election algorithm. The value 0 signifies + that the neighbor is not eligible to become the + Designated Router on this particular network." + DEFVAL { 1 } + ::= { ospfv3CfgNbrEntry 5 } + + ospfv3CfgNbrRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3CfgNbrEntry 6 } + + -- OSPFv3 Virtual Neighbor Table + + ospfv3VirtNbrTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3VirtNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A table describing all virtual neighbors." + REFERENCE + "OSPF Version 2, Section 15, Virtual Links" + ::= { ospfv3Objects 11 } + + ospfv3VirtNbrEntry OBJECT-TYPE + SYNTAX Ospfv3VirtNbrEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Virtual neighbor information." + INDEX { ospfv3VirtNbrArea, + ospfv3VirtNbrRtrId } + ::= { ospfv3VirtNbrTable 1 } + + Ospfv3VirtNbrEntry ::= SEQUENCE { + ospfv3VirtNbrArea + Ospfv3AreaIdTC, + ospfv3VirtNbrRtrId + Ospfv3RouterIdTC, + ospfv3VirtNbrIfIndex + InterfaceIndex, + ospfv3VirtNbrIfInstId + Ospfv3IfInstIdTC, + ospfv3VirtNbrAddressType + InetAddressType, + ospfv3VirtNbrAddress + InetAddress, + ospfv3VirtNbrOptions + Integer32, + ospfv3VirtNbrState + INTEGER, + ospfv3VirtNbrEvents + Counter32, + ospfv3VirtNbrLsRetransQLen + Gauge32, + ospfv3VirtNbrHelloSuppressed + TruthValue, + ospfv3VirtNbrIfId + InterfaceIndex, + ospfv3VirtNbrRestartHelperStatus + INTEGER, + ospfv3VirtNbrRestartHelperAge + Ospfv3UpToRefreshIntervalTC, + ospfv3VirtNbrRestartHelperExitReason + INTEGER + } + + ospfv3VirtNbrArea OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The transit area Identifier." + ::= { ospfv3VirtNbrEntry 1 } + + ospfv3VirtNbrRtrId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A 32-bit integer uniquely identifying the + neighboring router in the Autonomous System." + ::= { ospfv3VirtNbrEntry 2 } + + ospfv3VirtNbrIfIndex OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The local Interface ID for the virtual link over + which the neighbor can be reached." + ::= { ospfv3VirtNbrEntry 3 } + + ospfv3VirtNbrIfInstId OBJECT-TYPE + SYNTAX Ospfv3IfInstIdTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The interface instance for the virtual link over + which the neighbor can be reached." + ::= { ospfv3VirtNbrEntry 4 } + + ospfv3VirtNbrAddressType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The address type of ospfv3VirtNbrAddress. Only IPv6 + addresses without zone index are expected." + ::= { ospfv3VirtNbrEntry 5 } + + ospfv3VirtNbrAddress OBJECT-TYPE + SYNTAX InetAddress + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The IPv6 address advertised by this virtual neighbor. + It must be a global scope address." + ::= { ospfv3VirtNbrEntry 6 } + + ospfv3VirtNbrOptions OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "A bit mask corresponding to the neighbor's options + field." + REFERENCE + "OSPF for IPv6, Appendix A.2, The Options Field" + ::= { ospfv3VirtNbrEntry 7 } + + ospfv3VirtNbrState OBJECT-TYPE + SYNTAX INTEGER { + down(1), + attempt(2), + init(3), + twoWay(4), + exchangeStart(5), + exchange(6), + loading(7), + full(8) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The state of the virtual neighbor relationship." + ::= { ospfv3VirtNbrEntry 8 } + + ospfv3VirtNbrEvents OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The number of times this virtual link has + changed its state or an error has occurred. + + Discontinuities in the value of this counter + can occur at re-initialization of the management + system and at other times as indicated by the + value of ospfv3DiscontinuityTime." + ::= { ospfv3VirtNbrEntry 9 } + + ospfv3VirtNbrLsRetransQLen OBJECT-TYPE + SYNTAX Gauge32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The current length of the retransmission + queue." + ::= { ospfv3VirtNbrEntry 10 } + + ospfv3VirtNbrHelloSuppressed OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates whether Hellos are being suppressed + to the neighbor." + ::= { ospfv3VirtNbrEntry 11 } + + ospfv3VirtNbrIfId OBJECT-TYPE + SYNTAX InterfaceIndex + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The Interface ID that the neighbor advertises + in its Hello packets on this virtual link, that is, + the neighbor's local Interface ID." + ::= { ospfv3VirtNbrEntry 12 } + +ospfv3VirtNbrRestartHelperStatus OBJECT-TYPE + SYNTAX INTEGER { notHelping(1), + helping(2) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Indicates whether the router is acting + as a graceful restart helper for the neighbor." + ::= { ospfv3VirtNbrEntry 13 } + + ospfv3VirtNbrRestartHelperAge OBJECT-TYPE + SYNTAX Ospfv3UpToRefreshIntervalTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Remaining time in the current OSPF graceful restart + interval, if the router is acting as a restart + helper for the neighbor." + ::= { ospfv3VirtNbrEntry 14 } + + ospfv3VirtNbrRestartHelperExitReason OBJECT-TYPE + SYNTAX INTEGER { none(1), + inProgress(2), + completed(3), + timedOut(4), + topologyChanged(5) + } + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "Describes the outcome of the last attempt at acting + as a graceful restart helper for the neighbor. + + none: no restart has yet been attempted. + inProgress: a restart attempt is currently underway. + completed: the last restart completed successfully. + timedOut: the last restart timed out. + topologyChanged: the last restart was aborted due to + a topology change." + ::= { ospfv3VirtNbrEntry 15 } + + -- + -- The OSPFv3 Area Aggregate Table + -- + + ospfv3AreaAggregateTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3AreaAggregateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Area Aggregate Table acts as an adjunct + to the Area Table. It describes those address + aggregates that are configured to be propagated + from an area. Its purpose is to reduce the amount + of information that is known beyond an area's + borders. + + A range of IPv6 prefixes specified by a + prefix / prefix length pair. Note that if + ranges are configured such that one range + subsumes another range, the most specific + match is the preferred one." + ::= { ospfv3Objects 12 } + + ospfv3AreaAggregateEntry OBJECT-TYPE + SYNTAX Ospfv3AreaAggregateEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single area aggregate entry. + + Information in this table is persistent, and + when this object is written, the entity SHOULD + save the change to non-volatile storage." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + INDEX { ospfv3AreaAggregateAreaID, + ospfv3AreaAggregateAreaLsdbType, + ospfv3AreaAggregatePrefixType, + ospfv3AreaAggregatePrefix, + ospfv3AreaAggregatePrefixLength } + ::= { ospfv3AreaAggregateTable 1 } + + Ospfv3AreaAggregateEntry ::= SEQUENCE { + ospfv3AreaAggregateAreaID + Ospfv3AreaIdTC, + ospfv3AreaAggregateAreaLsdbType + INTEGER, + ospfv3AreaAggregatePrefixType + InetAddressType, + ospfv3AreaAggregatePrefix + InetAddress, + ospfv3AreaAggregatePrefixLength + InetAddressPrefixLength, + ospfv3AreaAggregateRowStatus + RowStatus, + ospfv3AreaAggregateEffect + INTEGER, + ospfv3AreaAggregateRouteTag + Unsigned32 + } + + ospfv3AreaAggregateAreaID OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The area the Address Aggregate is to be found + within." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3AreaAggregateEntry 1 } + + ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE + SYNTAX INTEGER { + interAreaPrefixLsa(8195), -- 0x2003 + nssaExternalLsa(8199) -- 0x2007 + } + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The type of the Address Aggregate. This field + specifies the Area LSDB type that this Address + Aggregate applies to." + REFERENCE + "OSPF Version 2, Appendix A.4.1, The LSA header" + ::= { ospfv3AreaAggregateEntry 2 } + + ospfv3AreaAggregatePrefixType OBJECT-TYPE + SYNTAX InetAddressType + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The prefix type of ospfv3AreaAggregatePrefix. Only + IPv6 addresses are expected." + ::= { ospfv3AreaAggregateEntry 3 } + + ospfv3AreaAggregatePrefix OBJECT-TYPE + SYNTAX InetAddress (SIZE (0..16)) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The IPv6 prefix." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3AreaAggregateEntry 4 } + + ospfv3AreaAggregatePrefixLength OBJECT-TYPE + SYNTAX InetAddressPrefixLength (3..128) + UNITS "bits" + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The length of the prefix (in bits). A prefix can + not be shorter than 3 bits." + REFERENCE + "OSPF Version 2, Appendix C.2, Area parameters" + ::= { ospfv3AreaAggregateEntry 5 } + + ospfv3AreaAggregateRowStatus OBJECT-TYPE + SYNTAX RowStatus + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This object permits management of the table by + facilitating actions such as row creation, + construction, and destruction. + + The value of this object has no effect on + whether other objects in this conceptual row can be + modified." + ::= { ospfv3AreaAggregateEntry 6 } + + ospfv3AreaAggregateEffect OBJECT-TYPE + SYNTAX INTEGER { + advertiseMatching(1), + doNotAdvertiseMatching(2) + } + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "Prefixes subsumed by ranges will either trigger the + advertisement of the indicated aggregate + (advertiseMatching) or result in the prefix not + being advertised at all outside the area." + DEFVAL { advertiseMatching } + ::= { ospfv3AreaAggregateEntry 7 } + + ospfv3AreaAggregateRouteTag OBJECT-TYPE + SYNTAX Unsigned32 + MAX-ACCESS read-create + STATUS current + DESCRIPTION + "This tag is advertised only in the summarized + As-External LSA when summarizing from NSSA-LSAs to + AS-External-LSAs." + DEFVAL { 0 } + ::= { ospfv3AreaAggregateEntry 8 } + + -- OSPFv3 Link-Scope Link State Database, for virtual interfaces + + ospfv3VirtLinkLsdbTable OBJECT-TYPE + SYNTAX SEQUENCE OF Ospfv3VirtLinkLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The OSPFv3 Process's Link-scope LSDB for virtual + interfaces. The LSDB contains the Link-scope link + state advertisements from virtual interfaces." + ::= { ospfv3Objects 13 } + + ospfv3VirtLinkLsdbEntry OBJECT-TYPE + SYNTAX Ospfv3VirtLinkLsdbEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "A single Link-scope link state advertisement + for a virtual interface." + INDEX { ospfv3VirtLinkLsdbIfAreaId, + ospfv3VirtLinkLsdbIfNeighbor, + ospfv3VirtLinkLsdbType, + ospfv3VirtLinkLsdbRouterId, + ospfv3VirtLinkLsdbLsid } + ::= { ospfv3VirtLinkLsdbTable 1 } + + Ospfv3VirtLinkLsdbEntry ::= SEQUENCE { + ospfv3VirtLinkLsdbIfAreaId + Ospfv3AreaIdTC, + ospfv3VirtLinkLsdbIfNeighbor + Ospfv3RouterIdTC, + ospfv3VirtLinkLsdbType + Unsigned32, + ospfv3VirtLinkLsdbRouterId + Ospfv3RouterIdTC, + ospfv3VirtLinkLsdbLsid + Ospfv3LsIdTC, + ospfv3VirtLinkLsdbSequence + Ospfv3LsaSequenceTC, + ospfv3VirtLinkLsdbAge + Ospfv3LsaAgeTC, + ospfv3VirtLinkLsdbChecksum + Integer32, + ospfv3VirtLinkLsdbAdvertisement + OCTET STRING, + ospfv3VirtLinkLsdbTypeKnown + TruthValue + } + + ospfv3VirtLinkLsdbIfAreaId OBJECT-TYPE + SYNTAX Ospfv3AreaIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The transit area that the virtual link + traverses. By definition, this is not + Area 0." + ::= { ospfv3VirtLinkLsdbEntry 1 } + + ospfv3VirtLinkLsdbIfNeighbor OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Router ID of the virtual neighbor." + ::= { ospfv3VirtLinkLsdbEntry 2 } + + ospfv3VirtLinkLsdbType OBJECT-TYPE + SYNTAX Unsigned32(0..'FFFFFFFF'h) + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The type of the link state advertisement. + Each link state type has a separate + advertisement format. Link-scope LSAs unrecognized + by the router are also stored in this database." + ::= { ospfv3VirtLinkLsdbEntry 3 } + + ospfv3VirtLinkLsdbRouterId OBJECT-TYPE + SYNTAX Ospfv3RouterIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The 32-bit number that uniquely identifies the + originating router in the Autonomous System." + REFERENCE + "OSPF Version 2, Appendix C.1, Global parameters" + ::= { ospfv3VirtLinkLsdbEntry 4 } + + ospfv3VirtLinkLsdbLsid OBJECT-TYPE + SYNTAX Ospfv3LsIdTC + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "The Link State ID is an LS type-specific field + containing a unique identifier; + it identifies the piece of the routing domain + that is being described by the advertisement. + In contrast to OSPFv2, the LSID has no + addressing semantics." + ::= { ospfv3VirtLinkLsdbEntry 5 } + + -- Note that the OSPF sequence number is a 32-bit signed + -- integer. It starts with the value '80000001'h + -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. + -- Thus, a typical sequence number will be very negative. + + ospfv3VirtLinkLsdbSequence OBJECT-TYPE + SYNTAX Ospfv3LsaSequenceTC + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The sequence number field is a signed 32-bit + integer. It is used to detect old and duplicate + link state advertisements. The space of + sequence numbers is linearly ordered. The + larger the sequence number, the more recent the + advertisement." + REFERENCE + "OSPF Version 2, Section 12.1.6, LS sequence + number" + ::= { ospfv3VirtLinkLsdbEntry 6 } + + ospfv3VirtLinkLsdbAge OBJECT-TYPE + SYNTAX Ospfv3LsaAgeTC + UNITS "seconds" + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the age of the link state + advertisement in seconds. The high-order bit + of the LS age field is considered the DoNotAge + bit for support of on-demand circuits." + REFERENCE + "OSPF Version 2, Section 12.1.1, LS age; + Extending OSPF to Support Demand Circuits, + Section 2.2, The LS age field." + ::= { ospfv3VirtLinkLsdbEntry 7 } + + ospfv3VirtLinkLsdbChecksum OBJECT-TYPE + SYNTAX Integer32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "This field is the checksum of the complete + contents of the advertisement, excepting the + age field. The age field is excepted so that + an advertisement's age can be incremented + without updating the checksum. The checksum + used is the same that is used for ISO + connectionless datagrams; it is commonly + referred to as the Fletcher checksum." + REFERENCE + "OSPF Version 2, Section 12.1.7, LS checksum" + ::= { ospfv3VirtLinkLsdbEntry 8 } + + ospfv3VirtLinkLsdbAdvertisement OBJECT-TYPE + SYNTAX OCTET STRING (SIZE (1..65535)) + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The entire link state advertisement, including + its header." + ::= { ospfv3VirtLinkLsdbEntry 9 } + + ospfv3VirtLinkLsdbTypeKnown OBJECT-TYPE + SYNTAX TruthValue + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value true (1) indicates that the LSA type is + recognized by this router." + ::= { ospfv3VirtLinkLsdbEntry 10 } + + -- The Ospfv3 Notification Table + + -- The Ospfv3 Notification Table records fields that are + -- required for notifications. + + ospfv3NotificationEntry OBJECT IDENTIFIER + ::= { ospfv3Objects 14 } + + ospfv3ConfigErrorType OBJECT-TYPE + SYNTAX INTEGER { + badVersion(1), + areaMismatch(2), + unknownNbmaNbr(3), -- Router is DR eligible + unknownVirtualNbr(4), + helloIntervalMismatch(5), + deadIntervalMismatch(6), + optionMismatch(7), + mtuMismatch(8), + duplicateRouterId(9), + noError(10) } + MAX-ACCESS accessible-for-notify + STATUS current + DESCRIPTION + "Potential types of configuration conflicts. + Used by the ospfv3ConfigError and + ospfv3ConfigVirtError notifications." + ::= { ospfv3NotificationEntry 1 } + + ospfv3PacketType OBJECT-TYPE + SYNTAX INTEGER { + hello(1), + dbDescript(2), + lsReq(3), + lsUpdate(4), + lsAck(5), + nullPacket(6) } + MAX-ACCESS accessible-for-notify + STATUS current + DESCRIPTION + "OSPFv3 packet types." + ::= { ospfv3NotificationEntry 2 } + + ospfv3PacketSrc OBJECT-TYPE + SYNTAX InetAddressIPv6 + MAX-ACCESS accessible-for-notify + STATUS current + DESCRIPTION + "The IPv6 address of an inbound packet that cannot + be identified by a neighbor instance. + + Only IPv6 addresses without zone index are expected." + ::= { ospfv3NotificationEntry 3 } + + -- Notification Definitions + + -- The notifications need to be throttled so as to not overwhelm the + -- management agent in case of rapid changes to the OSPFv3 module. + +ospfv3VirtIfStateChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3VirtIfState -- The new state + } + STATUS current + DESCRIPTION + "An ospfv3VirtIfStateChange notification signifies that + there has been a change in the state of an OSPFv3 virtual + interface. + + This notification should be generated when the interface + state regresses (e.g., goes from Point-to-Point to Down) + or progresses to a terminal state (i.e., Point-to-Point)." + ::= { ospfv3Notifications 1 } + +ospfv3NbrStateChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3NbrState -- The new state + + } + STATUS current + DESCRIPTION + "An ospfv3NbrStateChange notification signifies that + there has been a change in the state of a + non-virtual OSPFv3 neighbor. This notification should be + generated when the neighbor state regresses + (e.g., goes from Attempt or Full to 1-Way or + Down) or progresses to a terminal state (e.g., + 2-Way or Full). When a neighbor transitions + from or to Full on non-broadcast multi-access + and broadcast networks, the notification should be + generated by the Designated Router. A Designated + Router transitioning to Down will be noted by + ospfIfStateChange." + ::= { ospfv3Notifications 2 } + +ospfv3VirtNbrStateChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3VirtNbrState -- The new state + } + STATUS current + DESCRIPTION + "An ospfv3VirtNbrStateChange notification signifies + that there has been a change in the state of an OSPFv3 + virtual neighbor. This notification should be generated + when the neighbor state regresses (e.g., goes + from Attempt or Full to 1-Way or Down) or + progresses to a terminal state (e.g., Full)." + ::= { ospfv3Notifications 3 } + +ospfv3IfConfigError NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3IfState, -- State of the interface + ospfv3PacketSrc, -- IPv6 address of source + ospfv3ConfigErrorType, -- Type of error + ospfv3PacketType -- Type of packet + } + STATUS current + DESCRIPTION + "An ospfv3IfConfigError notification signifies that a + packet has been received on a non-virtual + interface from a router whose configuration + parameters conflict with this router's + configuration parameters. Note that the event + optionMismatch should cause a notification only if it + prevents an adjacency from forming." + ::= { ospfv3Notifications 4 } + +ospfv3VirtIfConfigError NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3VirtIfState, -- State of the interface + ospfv3ConfigErrorType, -- Type of error + ospfv3PacketType + } + STATUS current + DESCRIPTION + "An ospfv3VirtIfConfigError notification signifies that a + packet has been received on a virtual interface + from a router whose configuration parameters + conflict with this router's configuration + parameters. Note that the event optionMismatch + should cause a notification only if it prevents an + adjacency from forming." + ::= { ospfv3Notifications 5 } + +ospfv3IfRxBadPacket NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3IfState, -- State of the interface + ospfv3PacketSrc, -- The source IPv6 address + ospfv3PacketType -- Type of packet + } + STATUS current + DESCRIPTION + "An ospfv3IfRxBadPacket notification signifies that an + OSPFv3 packet that cannot be parsed has been received on a + non-virtual interface." + ::= { ospfv3Notifications 6 } + +ospfv3VirtIfRxBadPacket NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3VirtIfState, -- State of the interface + ospfv3PacketType -- Type of packet + } + STATUS current + DESCRIPTION + "An ospfv3VirtIfRxBadPacket notification signifies + that an OSPFv3 packet that cannot be parsed has been + received on a virtual interface." + ::= { ospfv3Notifications 7 } + +ospfv3LsdbOverflow NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3ExtAreaLsdbLimit -- Limit on External LSAs + } + STATUS current + DESCRIPTION + "An ospfv3LsdbOverflow notification signifies that the + number of LSAs in the router's link state + database has exceeded ospfv3ExtAreaLsdbLimit." + ::= { ospfv3Notifications 8 } + +ospfv3LsdbApproachingOverflow NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3ExtAreaLsdbLimit + } + STATUS current + DESCRIPTION + "An ospfv3LsdbApproachingOverflow notification signifies + that the number of LSAs in the router's + link state database has exceeded ninety percent of + ospfv3ExtAreaLsdbLimit." + ::= { ospfv3Notifications 9 } + +ospfv3IfStateChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3IfState -- The new state + } + STATUS current + DESCRIPTION + "An ospfv3IfStateChange notification signifies that there + has been a change in the state of a non-virtual + OSPFv3 interface. This notification should be generated + when the interface state regresses (e.g., goes + from DR to Down) or progresses to a terminal + state (i.e., Point-to-Point, DR Other, DR, or + Backup)." + ::= { ospfv3Notifications 10 } + +ospfv3NssaTranslatorStatusChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3AreaNssaTranslatorState -- new state + } + STATUS current + DESCRIPTION + "An ospfv3NssaTranslatorStatusChange notification + indicates that there has been a change in the router's + ability to translate OSPFv3 NSSA LSAs into OSPFv3 External + LSAs. This notification should be generated when the + Translator Status transitions from or to any defined + status on a per-area basis." + ::= { ospfv3Notifications 11 } + +ospfv3RestartStatusChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3RestartStatus, -- new status + ospfv3RestartInterval, + ospfv3RestartExitReason + } + STATUS current + DESCRIPTION + "An ospfv3RestartStatusChange notification signifies that + there has been a change in the graceful restart + state for the router. This notification should be + generated when the router restart status + changes." + ::= { ospfv3Notifications 12 } + +ospfv3NbrRestartHelperStatusChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3NbrRestartHelperStatus, -- new status + ospfv3NbrRestartHelperAge, + ospfv3NbrRestartHelperExitReason + } + STATUS current + DESCRIPTION + "An ospfv3NbrRestartHelperStatusChange notification + signifies that there has been a change in the + graceful restart helper state for the neighbor. + This notification should be generated when the + neighbor restart helper status transitions for a neighbor." + ::= { ospfv3Notifications 13 } + +ospfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPE + OBJECTS { ospfv3RouterId, -- The originator of the notification + ospfv3VirtNbrRestartHelperStatus, -- new status + ospfv3VirtNbrRestartHelperAge, + ospfv3VirtNbrRestartHelperExitReason + } + STATUS current + DESCRIPTION + "An ospfv3VirtNbrRestartHelperStatusChange + notification signifies that there has been a + change in the graceful restart helper state for + the virtual neighbor. This notification should be + generated when the virtual neighbor restart helper status + transitions for a virtual neighbor." + ::= { ospfv3Notifications 14 } + + -- Conformance Information + + ospfv3Groups OBJECT IDENTIFIER ::= { ospfv3Conformance 1 } + ospfv3Compliances OBJECT IDENTIFIER ::= { ospfv3Conformance 2 } + + -- Compliance Statements + + ospfv3FullCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION "The compliance statement" + MODULE -- this module + MANDATORY-GROUPS { + ospfv3BasicGroup, + ospfv3AreaGroup, + ospfv3IfGroup, + ospfv3VirtIfGroup, + ospfv3NbrGroup, + ospfv3CfgNbrGroup, + ospfv3VirtNbrGroup, + ospfv3AreaAggregateGroup + } + + GROUP ospfv3AsLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their AS-scope link state database." + + GROUP ospfv3AreaLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Area-scope link state database." + + GROUP ospfv3LinkLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Link-scope link state database + for non-virtual interfaces." + + GROUP ospfv3VirtLinkLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Link-scope link state database + for virtual interfaces." + + GROUP ospfv3HostGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support attached hosts." + + GROUP ospfv3NotificationObjectGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support OSPFv3 notifications." + + GROUP ospfv3NotificationGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support OSPFv3 notifications." + + OBJECT ospfv3NbrAddressType + SYNTAX InetAddressType { ipv6(2) } + DESCRIPTION + "An implementation is only required to support IPv6 + address without zone index." + + OBJECT ospfv3NbrAddress + SYNTAX InetAddress (SIZE (16)) + DESCRIPTION + "An implementation is only required to support IPv6 + address without zone index." + + OBJECT ospfv3VirtNbrAddressType + SYNTAX InetAddressType { ipv6(2) } + DESCRIPTION + "An implementation is only required to support IPv6 + address without zone index." + + OBJECT ospfv3VirtNbrAddress + SYNTAX InetAddress (SIZE (16)) + DESCRIPTION + "An implementation is only required to support IPv6 + address without zone index." + ::= { ospfv3Compliances 1 } + + ospfv3ReadOnlyCompliance MODULE-COMPLIANCE + STATUS current + DESCRIPTION + "When this MIB module is implemented without + support for read-create (i.e., in read-only + mode), the implementation can claim read-only + compliance. Such a device can then be monitored, + but cannot be configured with this MIB." + + MODULE -- this module + MANDATORY-GROUPS { + ospfv3BasicGroup, + ospfv3AreaGroup, + ospfv3IfGroup, + ospfv3VirtIfGroup, + ospfv3NbrGroup, + ospfv3CfgNbrGroup, + ospfv3VirtNbrGroup, + ospfv3AreaAggregateGroup + } + + GROUP ospfv3AsLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their AS-scope link state database." + + GROUP ospfv3AreaLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Area-scope link state database." + + GROUP ospfv3LinkLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Link-scope link state database + for non-virtual interfaces." + + GROUP ospfv3VirtLinkLsdbGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + display their Link-scope link state database + for virtual interfaces." + + GROUP ospfv3HostGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support attached hosts." + + GROUP ospfv3NotificationObjectGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support OSPFv3 notifications." + + GROUP ospfv3NotificationGroup + DESCRIPTION + "This group is required for OSPFv3 systems that + support OSPFv3 notifications." + + OBJECT ospfv3RouterId + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AdminStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3ExtAreaLsdbLimit + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3ExitOverflowInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3DemandExtensions + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3ReferenceBandwidth + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3RestartSupport + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3RestartInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3RestartStrictLsaChecking + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3NotificationEnable + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3StubRouterAdvertisement + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaImportAsExtern + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaSummary + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaStubMetric + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaNssaTranslatorRole + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaNssaTranslatorStabInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaStubMetricType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaTEEnabled + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3HostMetric + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3HostRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3HostAreaID + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfAreaId + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfType + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfAdminStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfRtrPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfTransitDelay + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfRetransInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfHelloInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfRtrDeadInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfPollInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfDemand + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfMetricValue + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfDemandNbrProbe + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfDemandNbrProbeRetransLimit + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfDemandNbrProbeInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfTEDisabled + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3IfLinkLSASuppression + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3VirtIfTransitDelay + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3VirtIfRetransInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3VirtIfHelloInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3VirtIfRtrDeadInterval + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3VirtIfRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3CfgNbrPriority + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3CfgNbrRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaAggregateRowStatus + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaAggregateEffect + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + + OBJECT ospfv3AreaAggregateRouteTag + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + ::= { ospfv3Compliances 2 } + + -- units of conformance + + ospfv3BasicGroup OBJECT-GROUP + OBJECTS { + ospfv3RouterId, + ospfv3AdminStatus, + ospfv3VersionNumber, + ospfv3AreaBdrRtrStatus, + ospfv3ASBdrRtrStatus, + ospfv3AsScopeLsaCount, + ospfv3AsScopeLsaCksumSum, + ospfv3OriginateNewLsas, + ospfv3RxNewLsas, + ospfv3ExtLsaCount, + ospfv3ExtAreaLsdbLimit, + ospfv3ExitOverflowInterval, + ospfv3DemandExtensions, + ospfv3ReferenceBandwidth, + ospfv3RestartSupport, + ospfv3RestartInterval, + ospfv3RestartStrictLsaChecking, + ospfv3RestartStatus, + ospfv3RestartAge, + ospfv3RestartExitReason, + ospfv3NotificationEnable, + ospfv3StubRouterSupport, + ospfv3StubRouterAdvertisement, + ospfv3DiscontinuityTime, + ospfv3RestartTime + } + STATUS current + DESCRIPTION + "These objects are used for managing/monitoring + OSPFv3 global parameters." + ::= { ospfv3Groups 1 } + + ospfv3AreaGroup OBJECT-GROUP + OBJECTS { + ospfv3AreaImportAsExtern, + ospfv3AreaSpfRuns, + ospfv3AreaBdrRtrCount, + ospfv3AreaAsBdrRtrCount, + ospfv3AreaScopeLsaCount, + ospfv3AreaScopeLsaCksumSum, + ospfv3AreaSummary, + ospfv3AreaRowStatus, + ospfv3AreaStubMetric, + ospfv3AreaNssaTranslatorRole, + ospfv3AreaNssaTranslatorState, + ospfv3AreaNssaTranslatorStabInterval, + ospfv3AreaNssaTranslatorEvents, + ospfv3AreaStubMetricType, + ospfv3AreaTEEnabled + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + supporting areas." + ::= { ospfv3Groups 2 } + + ospfv3AsLsdbGroup OBJECT-GROUP + OBJECTS { + ospfv3AsLsdbSequence, + ospfv3AsLsdbAge, + ospfv3AsLsdbChecksum, + ospfv3AsLsdbAdvertisement, + ospfv3AsLsdbTypeKnown + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + that display their AS-scope link state database." + ::= { ospfv3Groups 3 } + + ospfv3AreaLsdbGroup OBJECT-GROUP + OBJECTS { + ospfv3AreaLsdbSequence, + ospfv3AreaLsdbAge, + ospfv3AreaLsdbChecksum, + ospfv3AreaLsdbAdvertisement, + ospfv3AreaLsdbTypeKnown + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + that display their Area-scope link state database." + ::= { ospfv3Groups 4 } + + ospfv3LinkLsdbGroup OBJECT-GROUP + OBJECTS { + ospfv3LinkLsdbSequence, + ospfv3LinkLsdbAge, + ospfv3LinkLsdbChecksum, + ospfv3LinkLsdbAdvertisement, + ospfv3LinkLsdbTypeKnown + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + that display their Link-scope link state database + for non-virtual interfaces." + ::= { ospfv3Groups 5 } + + ospfv3HostGroup OBJECT-GROUP + OBJECTS { + ospfv3HostMetric, + ospfv3HostRowStatus, + ospfv3HostAreaID + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + that support attached hosts." + ::= { ospfv3Groups 6 } + + ospfv3IfGroup OBJECT-GROUP + OBJECTS { + ospfv3IfAreaId, + ospfv3IfType, + ospfv3IfAdminStatus, + ospfv3IfRtrPriority, + ospfv3IfTransitDelay, + ospfv3IfRetransInterval, + ospfv3IfHelloInterval, + ospfv3IfRtrDeadInterval, + ospfv3IfPollInterval, + ospfv3IfState, + ospfv3IfDesignatedRouter, + ospfv3IfBackupDesignatedRouter, + ospfv3IfEvents, + ospfv3IfRowStatus, + ospfv3IfDemand, + ospfv3IfMetricValue, + ospfv3IfLinkScopeLsaCount, + ospfv3IfLinkLsaCksumSum, + ospfv3IfDemandNbrProbe, + ospfv3IfDemandNbrProbeRetransLimit, + ospfv3IfDemandNbrProbeInterval, + ospfv3IfTEDisabled, + ospfv3IfLinkLSASuppression + } + STATUS current + DESCRIPTION + "These interface objects are used for + managing/monitoring OSPFv3 interfaces." + ::= { ospfv3Groups 7 } + + ospfv3VirtIfGroup OBJECT-GROUP + OBJECTS { + ospfv3VirtIfIndex, + ospfv3VirtIfInstId, + ospfv3VirtIfTransitDelay, + ospfv3VirtIfRetransInterval, + ospfv3VirtIfHelloInterval, + ospfv3VirtIfRtrDeadInterval, + ospfv3VirtIfState, + ospfv3VirtIfEvents, + ospfv3VirtIfRowStatus, + ospfv3VirtIfLinkScopeLsaCount, + ospfv3VirtIfLinkLsaCksumSum + } + STATUS current + DESCRIPTION + "These virtual interface objects are used for + managing/monitoring OSPFv3 virtual interfaces." + ::= { ospfv3Groups 8 } + + ospfv3NbrGroup OBJECT-GROUP + OBJECTS { + ospfv3NbrAddressType, + ospfv3NbrAddress, + ospfv3NbrOptions, + ospfv3NbrPriority, + ospfv3NbrState, + ospfv3NbrEvents, + ospfv3NbrLsRetransQLen, + ospfv3NbrHelloSuppressed, + ospfv3NbrIfId, + ospfv3NbrRestartHelperStatus, + ospfv3NbrRestartHelperAge, + ospfv3NbrRestartHelperExitReason + } + STATUS current + DESCRIPTION + "These neighbor objects are used for + managing/monitoring OSPFv3 neighbors." + ::= { ospfv3Groups 9 } + + ospfv3CfgNbrGroup OBJECT-GROUP + OBJECTS { + ospfv3CfgNbrPriority, + ospfv3CfgNbrRowStatus + } + STATUS current + DESCRIPTION + "These configured neighbor objects are used for + managing/monitoring OSPFv3-configured neighbors." + ::= { ospfv3Groups 10 } + + ospfv3VirtNbrGroup OBJECT-GROUP + OBJECTS { + ospfv3VirtNbrIfIndex, + ospfv3VirtNbrIfInstId, + ospfv3VirtNbrAddressType, + ospfv3VirtNbrAddress, + ospfv3VirtNbrOptions, + ospfv3VirtNbrState, + ospfv3VirtNbrEvents, + ospfv3VirtNbrLsRetransQLen, + ospfv3VirtNbrHelloSuppressed, + ospfv3VirtNbrIfId, + ospfv3VirtNbrRestartHelperStatus, + ospfv3VirtNbrRestartHelperAge, + ospfv3VirtNbrRestartHelperExitReason + } + STATUS current + DESCRIPTION + "These virtual neighbor objects are used for + managing/monitoring OSPFv3 virtual neighbors." + ::= { ospfv3Groups 11 } + + ospfv3AreaAggregateGroup OBJECT-GROUP + OBJECTS { + ospfv3AreaAggregateRowStatus, + ospfv3AreaAggregateEffect, + ospfv3AreaAggregateRouteTag + } + STATUS current + DESCRIPTION + "These area aggregate objects are required for + aggregating OSPFv3 prefixes for summarization + across areas." + ::= { ospfv3Groups 12 } + + ospfv3VirtLinkLsdbGroup OBJECT-GROUP + OBJECTS { + ospfv3VirtLinkLsdbSequence, + ospfv3VirtLinkLsdbAge, + ospfv3VirtLinkLsdbChecksum, + ospfv3VirtLinkLsdbAdvertisement, + ospfv3VirtLinkLsdbTypeKnown + } + STATUS current + DESCRIPTION + "These objects are used for OSPFv3 systems + that display their Link-scope link state database + for virtual interfaces." + ::= { ospfv3Groups 13 } + + ospfv3NotificationObjectGroup OBJECT-GROUP + OBJECTS { + ospfv3ConfigErrorType, + ospfv3PacketType, + ospfv3PacketSrc + } + STATUS current + DESCRIPTION + "These objects are used to record notification + parameters." + ::= { ospfv3Groups 14 } + + ospfv3NotificationGroup NOTIFICATION-GROUP + NOTIFICATIONS { + ospfv3VirtIfStateChange, + ospfv3NbrStateChange, + ospfv3VirtNbrStateChange, + ospfv3IfConfigError, + ospfv3VirtIfConfigError, + ospfv3IfRxBadPacket, + ospfv3VirtIfRxBadPacket, + ospfv3LsdbOverflow, + ospfv3LsdbApproachingOverflow, + ospfv3IfStateChange, + ospfv3NssaTranslatorStatusChange, + ospfv3RestartStatusChange, + ospfv3NbrRestartHelperStatusChange, + ospfv3VirtNbrRestartHelperStatusChange + } + STATUS current + DESCRIPTION + "This group is used for OSPFv3 notifications." + ::= { ospfv3Groups 15 } + + END |