summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-02-24Remove unused function "st_set_position"midopple
2012-02-24Add "store_eeprom.cpp" to makefilemidopple
2012-02-24fix applet/core.a: not found --> Thanks to triffidmidopple
2012-02-24Changhe PWM Value from INT to unsigned char, is faster for interruptmidopple
2012-02-24compile experimental using the MakefileJoachim Schleicher
* add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile
2012-02-23Merge pull request #142 from jschleic/fix-comment_modekliment
fix comment mode.
2012-02-23Merge pull request #141 from jschleic/fix-Makefile2kliment
Fix Makefile in experimental
2012-02-23fix comment mode.Joachim Schleicher
Closes #140. If a line starts with ';', it is ignored but comment_mode is reset. A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. Probably a similar fix is necessary for the SDSUPPORT part; I cannot test that part without an SD-shield.
2012-02-23compile experimental using the MakefileJoachim Schleicher
* add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile
2012-02-23Thermistortable temptable_4 midopple
correct declaration: const short temptable_4[NUMTEMPS_4][2]
2012-02-22Merge pull request #139 from triffid/makefile-fixkliment
fix applet/core.a: not found
2012-02-22fix applet/core.a: not foundMichael Moon
2012-02-21Merge pull request #137 from midopple/experimentalkliment
EEPROM function and small Changes
2012-02-17The microcontroller can store settings to EEPROMmidopple
to use the fuction set in configuration.h #define USE_EEPROM_SETTINGS --> Save and recall Settings aktive #define PRINT_EEPROM_SETTING --> Print settings to UART Commands: M500 - stores paramters in EEPROM M501 - reads parameters from EEPROM M502 - reverts to the default M503 - Print Settings
2012-02-15- changed homing function to not conflict with ↵midopple
min_software_endstops/max_software_endstops (thanks rGlory) - Corrected distance calculation. (thanks jv4779)
2012-02-15Standardvalue MAX Feed Rate for Z-Axis reduced to 2 mm/s some Printers had ↵midopple
problems with 4 mm/s
2012-02-14Changed check in arc_funcmidopple
if (millimeters_of_travel == 0.0) => if (millimeters_of_travel < 0.001) (thanks mooselake)
2012-02-13Merge pull request #136 from rGlory/e2e9fb45fa36cc9fe2be50b9133f1e17d00d015bkliment
Home function fix
2012-02-13changed homing function to not conflict with ↵Vyacheslav Kononenko
min_software_endstops/max_software_endstops
2012-02-06Add pin definition for the Printrboard Rev B --> Thaks to lwalkeramidopple
2012-02-05Merge pull request #134 from lwalkera/printrboardkliment
Add pin definition for the Printrboard Rev B
2012-02-05Add pin definition for the Printrboard Rev BLaine Walker-Avina
2012-02-05Merge pull request #133 from midopple/experimentalkliment
Experimental new Planner Code
2012-02-05- Implement Plannercode from Marlin V1 --> big thanks to Erikmidopple
- Stepper interrupt with Step loops - Stepperfrequenz 30 Khz - New Command * M202 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec * M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 * M205 - advanced settings: minimum travel speed S=while printing T=travel only, X= maximum xy jerk, Z=maximum Z jerk - Remove unused Variables - Check Uart Puffer while circle processing (CMD: G2 / G3) - Fast Xfer Function --> move Text to Flash - Option to deaktivate ARC (G2/G3) function (save flash) - Removed modulo (%) operator, which uses an expensive divide
2012-02-02Without the PID control for Hotend the tempmonitor use the wrong variablemidopple
2012-02-02Option to deaktivate the arc functionmidopple
2012-02-01Check Uart Puffer while circle processing (CMD: G2 / G3)midopple
2012-01-29Merge commit '132f8c212e4c316559177e532df6b9a6c2205bf2' into experimentalmidopple
2012-01-29Merge pull request #131 from midopple/SprinterV2kliment
Lookahead, timer-based stepping, M30 file delete
2012-01-29Add function to check the UART buffer while arc function is workingmidopple
2012-01-29Update Changelog in Mainfilemidopple
2012-01-29Change Motherboard to 3 (standardsettings)midopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
Conflicts: Sprinter/Configuration.h Sprinter/Sprinter.pde
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
Conflicts: Sprinter/Configuration.h
2012-01-29Change configuration.h to original settingsmidopple
2012-01-29Change infotextmidopple
2012-01-29New Version Sprinter V2midopple
- Look Vorward Funktion - - Stepper Control with Timer 1 - SOFT PWM for Extruder heating --> Free Timer 1 - G2 / G3 Command for arc real arc - Baudrate 250 kbaud - M30 Command delete file on SD Card - Text moved to flash to free RAM - M203 Command for Temp debugging
2012-01-28Update Sprinter/Configuration.hmidopple
2012-01-27Merge pull request #129 from jschleic/patch-1kliment
Improve Makefile to rebuild on upload
2012-01-27fix indentationJoachim Schleicher
This should be a comment. Instead it is printed together with the 'upload' target, when idented.
2012-01-22Merge pull request #128 from blddk/experimentalkliment
Reported wrong temperature in M190
2012-01-22Reported wrong temperature while heating upblddk
2012-01-22Merge pull request #127 from blddk/experimentalkliment
Stepper enable delay and temperature table Fix bed temp reading in M190
2012-01-22Changed temperature table for bed, to the one for the bed, instead of for ↵blddk
the heater.
2012-01-22Added option to set a delay after enabling a stepper driver, default turned ↵blddk
off to keep current behavior.
2012-01-22Added option to set a delay after enabeling stepper driver, to allow the ↵blddk
driver to enable (time needed according to datasheet)
2012-01-20correct dependencies in MakefileJoachim Schleicher
applet/$(TARGET).elf should depend on the cpp file, not on .pde so that the cpp is rebuilt when pde changes. We drop the target applet_files to achieve the correct behaviour. Now 'make upload' does rebuild the hex file as well.
2011-12-10Merge pull request #125 from gdahlm/experimentalkliment
Fixes for Gen7 Support #2
2011-12-10Merge pull request #126 from ERoth3/patch-1kliment
Updated readme with a warning about Arduino V1.0 incompatibility.
2011-12-10Updated readme with a warning about Arduino V1.0 incompatibility. ERoth3
generated by cgit v1.2.1 (git 2.18.0) at 2024-07-01 16:52:17 +0000