summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-08-12Merge pull request #67 from rotorit/masterkliment
use the fan pin to power the hot end heater on the crappy techzone monotronics
2011-08-09first revision... had to use the fan pin to control the extruder hot end ↵rotorit
heater. meaning.. this setup will not support a bed heat control ..for now... Time will show if I can get the Tip management A/D converter to work... or.. should i get it to work at all???
2011-08-09Merge pull request #66 from rotorit/masterkliment
Limited Gen 3 with 644P support - support gen3 with gen3+ board and the techzone monolithic electronics with thermistor only
2011-08-09typorotorit
2011-08-09Edited Sprinter/Configuration.h via GitHubrotorit
2011-08-09Added support for Gen3-pluss and Gen3-Monolithic Electronicsrotorit
2011-08-09added motherboard entry for Gen3-pluss and Gen3-Monolithic Electronicsrotorit
2011-07-25Merge pull request #58 from Renosis/masterkliment
MakerGear Hybrid Prusa Mendel steps per unit values
2011-07-24Added MakerGear Hybrid Prusa steps per unit values.Spencer Renosis
2011-07-24Merge branch 'experimental'kliment
2011-07-24Merge remote branch 'origin/experimental' into experimentalEmanuele Caruso
2011-07-24Fixed bug which in some cases caused the moves to be done at full speed ↵Emanuele Caruso
without acceleration
2011-07-23Merge pull request #55 from Joaz/uuidkliment
added uuid identification support
2011-07-24added uuid identification supportjglauche
2011-07-18Merge branch 'master' into experimentalkliment
2011-07-17Merge pull request #54 from ERoth3/masterkliment
Added Ramps 1.3 Pin assignments for E1
2011-07-18Added Ramps 1.3 pin assignments for E1 (second extruder) stepper driverEmery Roth
This is my first commit…Please don't hurt me if i screw up!
2011-07-17Merge branch 'master' into experimentalkliment
2011-07-17Add some explanations to config, change some variables to #defines. Fixes #36kliment
2011-07-17Merge branch 'master' into experimentalkliment
2011-07-17Add extra config for homing feedrate - fixes #28kliment
2011-07-16Merge branch 'master' into experimentalkliment
2011-07-16Ignore bedtemp if no bed temp pin definedkliment
2011-07-16Merge branch 'master' of github.com:kliment/Sprinter into experimentalkliment
2011-07-16Merge pull request #52 from alexrj/inverted-homingkliment
Fix homing to max endstops
2011-07-16Bugfix: homing to max endstops didn't work because current_position was ↵Alessandro Ranellucci
always reset to 0.
2011-07-16Merge branch 'master' of github.com:kliment/Sprinter into experimentalkliment
2011-07-16Merge pull request #51 from alexrj/temp-smoothingkliment
Respect HEATER_USES_* when initializing temperature smoothing
2011-07-16Bugfix: smoothed temperature was initialized without respecting HEATER_USES_*Alessandro Ranellucci
2011-07-15Revert "Remove float conversions from step loop"kliment
This reverts commit b31c7a837ff5baff89043f3c06b1b2191ed9f79d.
2011-07-15Remove float conversions from step loopkliment
2011-07-15Add extended pin definition for 168/328 to fastio (analog pins)kliment
2011-07-15Extended pindefs for mega 1280/2560 (analog pins)kliment
2011-07-12Merge branch 'master' into experimentalkliment
2011-07-12Add 10k thermistorkliment
2011-07-12Merge branch 'master' into experimentalkliment
2011-07-12Merge pull request #49 from alexrj/masterkliment
Fix overflow on very long moves
2011-07-12Bugfix: bad math for long distance moves.Alessandro Ranellucci
2011-07-11Merge pull request #48 from rodrigob/experimentalkliment
Compilation/uploading guide for newbies
2011-07-11Fixing some typosRodrigo Benenson
2011-07-11Added link to http://reprap.org/wiki/Sanguinololu#EndstopsRodrigo Benenson
2011-07-11Extended the README so newbies now what to doRodrigo Benenson
2011-07-11Merge branch 'master' into experimentalkliment
2011-07-11Fix for AD595 as bed temp sensorkliment
2011-07-11Fix temp handling for AD595kliment
2011-07-10Merge branch 'master' into experimentalkliment
2011-07-10Fix G28 commandkliment
2011-07-10Fix typo in variable namekliment
2011-07-10Attempt to complete move if non-primary axis endstop hit, otherwise abort ↵kliment
move and save position
2011-07-10Force boolean return in READkliment