summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-03-13Merge pull request #4 from metzench/patch-1midopple
Update pins.h for gen7
2012-03-13Update pins.h for gen7, working setup for 20MHzChristian Metzen
2012-03-13Info about GEN7 @ 20Mhz midopple
right Fuses settings for Bootloader
2012-03-12calculate feedrate without extrude before planner block is setmidopple
2012-03-10New Board --> GEN7 @ 20 Mhzmidopple
Select in configuration.h --> #define MOTHERBOARD 71 New Speedtable for 16 Mhz and 20 Mhz
2012-03-05Merge pull request #148 from midopple/experimentalkliment
Slowdown Function when Plannerpuffer is low
2012-03-04Merge commit 'from changwoo/arduino-1.0-compatibility' into experimentalmidopple
2012-03-04Merge pull request #147 from changwoo/arduino-1.0-compatibilitykliment
Arduino 1.0 compatibility for experimental
2012-03-04Move SLOWDOWN Funktion up, at the current position does not workmidopple
2012-03-05Update README on Arduino v1 supportChangwoo Ryu
2012-03-05Correct SD for Arduino 1.0 compatibilityChangwoo Ryu
With Arduino 1.0 Print class: - write() should return, and - print() with a uint_8 or int_8 character argument does not call print(char) anymore. So character argument should be casted to 'char' explicitly.
2012-02-24Merge pull request #144 from midopple/experimentalkliment
Fix Comment, Optimize, remove Unused code, fix makefile
2012-02-24Merge commit '89180de4bfd598298f4d5e77889c57a250e35084' into experimentalmidopple
Conflicts: Sprinter/Makefile
2012-02-24If a line starts with ';', it is ignored but comment_mode is reset.midopple
A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. --> Tanks to jschleic Same fix for SD Card, testet and work (midopple)
2012-02-24Version 1.3.07Tmidopple
- Optimize Variable Size (faster Code) --> heater.cpp - Remove unused Code from Interrupt --> faster ~ 22 us per step - Replace abs with fabs --> Faster and smaler
2012-02-24Remove unused function "st_set_position"midopple
2012-02-24Add "store_eeprom.cpp" to makefilemidopple
2012-02-24fix applet/core.a: not found --> Thanks to triffidmidopple
2012-02-24Changhe PWM Value from INT to unsigned char, is faster for interruptmidopple
2012-02-24compile experimental using the MakefileJoachim Schleicher
* add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile
2012-02-23Merge pull request #142 from jschleic/fix-comment_modekliment
fix comment mode.
2012-02-23Merge pull request #141 from jschleic/fix-Makefile2kliment
Fix Makefile in experimental
2012-02-23fix comment mode.Joachim Schleicher
Closes #140. If a line starts with ';', it is ignored but comment_mode is reset. A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. Probably a similar fix is necessary for the SDSUPPORT part; I cannot test that part without an SD-shield.
2012-02-23compile experimental using the MakefileJoachim Schleicher
* add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile
2012-02-23Thermistortable temptable_4 midopple
correct declaration: const short temptable_4[NUMTEMPS_4][2]
2012-02-22Merge pull request #139 from triffid/makefile-fixkliment
fix applet/core.a: not found
2012-02-22fix applet/core.a: not foundMichael Moon
2012-02-21Merge pull request #137 from midopple/experimentalkliment
EEPROM function and small Changes
2012-02-17The microcontroller can store settings to EEPROMmidopple
to use the fuction set in configuration.h #define USE_EEPROM_SETTINGS --> Save and recall Settings aktive #define PRINT_EEPROM_SETTING --> Print settings to UART Commands: M500 - stores paramters in EEPROM M501 - reads parameters from EEPROM M502 - reverts to the default M503 - Print Settings
2012-02-15- changed homing function to not conflict with ↵midopple
min_software_endstops/max_software_endstops (thanks rGlory) - Corrected distance calculation. (thanks jv4779)
2012-02-15Standardvalue MAX Feed Rate for Z-Axis reduced to 2 mm/s some Printers had ↵midopple
problems with 4 mm/s
2012-02-14Changed check in arc_funcmidopple
if (millimeters_of_travel == 0.0) => if (millimeters_of_travel < 0.001) (thanks mooselake)
2012-02-13Merge pull request #136 from rGlory/e2e9fb45fa36cc9fe2be50b9133f1e17d00d015bkliment
Home function fix
2012-02-13changed homing function to not conflict with ↵Vyacheslav Kononenko
min_software_endstops/max_software_endstops
2012-02-06Add pin definition for the Printrboard Rev B --> Thaks to lwalkeramidopple
2012-02-05Merge pull request #134 from lwalkera/printrboardkliment
Add pin definition for the Printrboard Rev B
2012-02-05Add pin definition for the Printrboard Rev BLaine Walker-Avina
2012-02-05Merge pull request #133 from midopple/experimentalkliment
Experimental new Planner Code
2012-02-05- Implement Plannercode from Marlin V1 --> big thanks to Erikmidopple
- Stepper interrupt with Step loops - Stepperfrequenz 30 Khz - New Command * M202 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec * M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 * M205 - advanced settings: minimum travel speed S=while printing T=travel only, X= maximum xy jerk, Z=maximum Z jerk - Remove unused Variables - Check Uart Puffer while circle processing (CMD: G2 / G3) - Fast Xfer Function --> move Text to Flash - Option to deaktivate ARC (G2/G3) function (save flash) - Removed modulo (%) operator, which uses an expensive divide
2012-02-02Without the PID control for Hotend the tempmonitor use the wrong variablemidopple
2012-02-02Option to deaktivate the arc functionmidopple
2012-02-01Check Uart Puffer while circle processing (CMD: G2 / G3)midopple
2012-01-29Merge commit '132f8c212e4c316559177e532df6b9a6c2205bf2' into experimentalmidopple
2012-01-29Merge pull request #131 from midopple/SprinterV2kliment
Lookahead, timer-based stepping, M30 file delete
2012-01-29Add function to check the UART buffer while arc function is workingmidopple
2012-01-29Update Changelog in Mainfilemidopple
2012-01-29Change Motherboard to 3 (standardsettings)midopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
Conflicts: Sprinter/Configuration.h Sprinter/Sprinter.pde
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
Conflicts: Sprinter/Configuration.h
2012-01-29Change configuration.h to original settingsmidopple
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-09 23:14:19 +0000