summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-05-24Too many if('sblddk
2012-05-24Wrong declaration for Variable min_time_before_dir_change midopple
should be const long
2012-05-21Arduino 1.0 buildChangwoo Ryu
2012-05-17Merge pull request #171 from kliment/mastermidopple
additional dropsegments test
2012-05-16If a small move is drop and the next move is retract the speed is wrong ↵midopple
calculated see https://github.com/kliment/Sprinter/issues/170 thanks to jschleic
2012-05-15Add MOTHERBOARD 51 for GEN6 with Heatbed and Heatbedsensormidopple
2012-05-04Version 1.3.17Tmidopple
- M303 - PID relay autotune possible - G4 Wait until last move is done
2012-05-01Merge pull request #168 from kliment/mastermidopple
Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is
2012-05-01Merge pull request #167 from OhmEye/masterkliment
Fix compile error if SD_FAST_XFER_AKTIV is on and PID is off
2012-04-30Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID isOhmEye
enabled. Fix: If SD_FAST_XFER_AKTIV is defined, fast_xfer() only declares g_heater_pwm_val if PIDTEMP is defined, but later assigns g_heater_pwm_val=0 regardless whether PIDTEMP is defined or not. If PIDTEMP is undefined, g_heater_pwm_val is undeclared at compile time and generates the appropriate error. I solved by not using g_heater_pwm_val if PIDTEMP is undefined (and therefor undeclared.) Also, the extern declaration was as an int, when g_heater_pwm_val is defined as a volatile unsigned char. This caused a duplicate declaration error, which was solved by changing the declaration in fast_xfer() to match the definition. I didn't dig deeper to try to understand if the mismatch was intentional or test operation other than verify the compile errors no longer occur.
2012-04-24Fix commit Textmidopple
2012-04-24Extra Retract Feedrate for Extrudermidopple
- Use extra extruder feedrate limit for reverse moves, and also the first forward move after a reverse
2012-04-24Fix typo in Parameteroutputmidopple
2012-04-23Ignore ":" in comments.midopple
2012-04-22Version 1.3.15Tmidopple
- M206 - set additional homeing offset (Thank to se5a for this idea) (First Version is without saving to EEPROM) - Option for minimum FAN start speed --> #define MINIMUM_FAN_START_SPEED 50 (set it to zero to deaktivate)
2012-04-20When endstop is hit count virtual steps, so the print lose no position when ↵midopple
endstop is hit
2012-04-20- Extrudmultiply with code M221 Sxxx (S100 original Extrude value)midopple
- use Feedratefaktor only when Extruded lenght > 0 - M106 / M107 can drive the FAN with PWM + Port check for not using Timer 1 - New Option --> FAN_SOFT_PWM, with this option the FAN PWM can use every digital I/O (PWM with 500 hz) - Added M93 command. Sends current steps for all axis.
2012-04-02Fixed small bug in arcs when segemnts are zeromidopple
Thanks to hurzl
2012-04-01Merge pull request #161 from se5a/masterkliment
Added M93 command - sends current steps per unit for all axis
2012-04-02Added M93 command. sends current steps for all axis se5a
2012-03-30Merge pull request #160 from kliment/masterkliment
Command M106 / M107
2012-03-30Command M106 / M107 for control the fan can use PWM midopple
New function to check the used PWM pins
2012-03-30Command M106 / M107 for control the fan can use PWM midopple
New function to check the used PWM pins
2012-03-28Merge pull request #159 from midopple/experimentalmidopple
Fixed arc offset
2012-03-28Merge from experimental, thanks to triffid_huntermidopple
2012-03-28Merge pull request #158 from kliment/masterkliment
fix compiling from makefile
2012-03-28Merge pull request #157 from triffid/fix-orderkliment
fix enable_endstops being used before its definition
2012-03-28fix enable_endstops being used before its definitionMichael Moon
2012-03-28add my namemidopple
2012-03-28add my namemidopple
2012-03-27Fixed arc offsetmidopple
Thanks to Erik van der Zalm
2012-03-27Merge commit '0c36faa8034f2c21e834efcff73aa41137be31dd' into experimentalmidopple
2012-03-27Set the defaults for the heart of the sun...uhm, set default board to 33Kliment Yanev
2012-03-27Merge pull request #156 from midopple/experimentalkliment
wrong char in configuration.h
2012-03-23First char '#' was unicode so linux give an compile errormidopple
2012-03-19Merge pull request #155 from midopple/experimentalkliment
Try to merge fixes from Master into Experimental
2012-03-19Fixes virtual endstops when using mixed physical endstop positions.midopple
Thanks to ticking
2012-03-19Merge commit pins.h from master to experimentellmidopple
Conflicts: Sprinter/pins.h
2012-03-19Merge pull request #154 from midopple/experimentalkliment
AT90USB128x / Speedtable with F_CPU / fix include Closes #145
2012-03-19Version 1.3.11Tmidopple
- fix for broken include in store_eeprom.cpp --> Thanks to kmeehl (issue #145) - Make fastio & Arduino pin numbering consistent for AT90USB128x. --> Thanks to lincomatic - Select Speedtable with F_CPU - Use same Values for Speedtables as Marlin
2012-03-19fix for broken include in store_eeprom.cppmidopple
Thanks to kmeehl
2012-03-19Make fastio & Arduino pin numbering consistent for AT90USB128x.midopple
Thanks to lincomatic
2012-03-18Merge pull request #152 from lincomatic/masterkliment
Make fastio & Teensyduino Pin Numbering consistent with each other for AT90USB128x
2012-03-17Make fastio & Arduino pin numbering consistent for AT90USB128xlincomatic
2012-03-14Merge pull request #150 from midopple/experimentalkliment
Fix gen7 support, fix bug in ENDSTOPS_ONLY_FOR_HOMING
2012-03-14ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared midopple
New Version V1.3.10T
2012-03-13Add info to GEN7 Pinsmidopple
2012-03-13Merge pull request #4 from metzench/patch-1midopple
Update pins.h for gen7
2012-03-13Update pins.h for gen7, working setup for 20MHzChristian Metzen
2012-03-13Info about GEN7 @ 20Mhz midopple
right Fuses settings for Bootloader
generated by cgit v1.2.1 (git 2.18.0) at 2024-05-17 09:27:17 +0000