summaryrefslogtreecommitdiff
path: root/Sprinter
AgeCommit message (Expand)Author
2012-03-17Make fastio & Arduino pin numbering consistent for AT90USB128xlincomatic
2012-03-14ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared midopple
2012-03-13Add info to GEN7 Pinsmidopple
2012-03-13Update pins.h for gen7, working setup for 20MHzChristian Metzen
2012-03-12calculate feedrate without extrude before planner block is setmidopple
2012-03-10New Board --> GEN7 @ 20 Mhzmidopple
2012-03-04Merge commit 'from changwoo/arduino-1.0-compatibility' into experimentalmidopple
2012-03-04Move SLOWDOWN Funktion up, at the current position does not workmidopple
2012-03-05Correct SD for Arduino 1.0 compatibilityChangwoo Ryu
2012-02-24Merge commit '89180de4bfd598298f4d5e77889c57a250e35084' into experimentalmidopple
2012-02-24If a line starts with ';', it is ignored but comment_mode is reset.midopple
2012-02-24Version 1.3.07Tmidopple
2012-02-24Remove unused function "st_set_position"midopple
2012-02-24Add "store_eeprom.cpp" to makefilemidopple
2012-02-24fix applet/core.a: not found --> Thanks to triffidmidopple
2012-02-24Changhe PWM Value from INT to unsigned char, is faster for interruptmidopple
2012-02-24compile experimental using the MakefileJoachim Schleicher
2012-02-23fix comment mode.Joachim Schleicher
2012-02-23compile experimental using the MakefileJoachim Schleicher
2012-02-23Thermistortable temptable_4 midopple
2012-02-22fix applet/core.a: not foundMichael Moon
2012-02-17The microcontroller can store settings to EEPROMmidopple
2012-02-15- changed homing function to not conflict with min_software_endstops/max_soft...midopple
2012-02-15Standardvalue MAX Feed Rate for Z-Axis reduced to 2 mm/s some Printers had pr...midopple
2012-02-14Changed check in arc_funcmidopple
2012-02-13changed homing function to not conflict with min_software_endstops/max_softwa...Vyacheslav Kononenko
2012-02-06Add pin definition for the Printrboard Rev B --> Thaks to lwalkeramidopple
2012-02-05Add pin definition for the Printrboard Rev BLaine Walker-Avina
2012-02-05- Implement Plannercode from Marlin V1 --> big thanks to Erikmidopple
2012-02-02Without the PID control for Hotend the tempmonitor use the wrong variablemidopple
2012-02-02Option to deaktivate the arc functionmidopple
2012-02-01Check Uart Puffer while circle processing (CMD: G2 / G3)midopple
2012-01-29Add function to check the UART buffer while arc function is workingmidopple
2012-01-29Update Changelog in Mainfilemidopple
2012-01-29Change Motherboard to 3 (standardsettings)midopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
2012-01-29Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2midopple
2012-01-29Change configuration.h to original settingsmidopple
2012-01-29Change infotextmidopple
2012-01-29New Version Sprinter V2midopple
2012-01-28Update Sprinter/Configuration.hmidopple
2012-01-27fix indentationJoachim Schleicher
2012-01-22Reported wrong temperature while heating upblddk
2012-01-22Changed temperature table for bed, to the one for the bed, instead of for the...blddk
2012-01-22Added option to set a delay after enabling a stepper driver, default turned o...blddk
2012-01-22Added option to set a delay after enabeling stepper driver, to allow the driv...blddk
2012-01-20correct dependencies in MakefileJoachim Schleicher
2011-12-06Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 board...Greg Dahlman
2011-12-05Fixing issues in pins.h and fastio.h, I created them not understanding it was...Greg Dahlman
2011-12-04Added an option to make init.g on SD run on boot.Nathan Zadoks
generated by cgit v1.2.1 (git 2.18.0) at 2024-06-18 11:26:32 +0000