| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-06-11 | Error with Command M201, when this Command is use the same Values are ↵ | midopple | |
| written to maximum Feedrate. | |||
| 2012-06-02 | Bug in heater.cpp --> Thermistor type 3, disconnecting thermistor yields ↵ | midopple | |
| temp -20, and hotend gets switched to full power | |||
| 2012-05-24 | Wrong declaration for Variable min_time_before_dir_change | midopple | |
| should be const long | |||
| 2012-05-16 | If a small move is drop and the next move is retract the speed is wrong ↵ | midopple | |
| calculated see https://github.com/kliment/Sprinter/issues/170 thanks to jschleic | |||
| 2012-05-01 | Merge pull request #167 from OhmEye/master | kliment | |
| Fix compile error if SD_FAST_XFER_AKTIV is on and PID is off | |||
| 2012-04-30 | Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | OhmEye | |
| enabled. Fix: If SD_FAST_XFER_AKTIV is defined, fast_xfer() only declares g_heater_pwm_val if PIDTEMP is defined, but later assigns g_heater_pwm_val=0 regardless whether PIDTEMP is defined or not. If PIDTEMP is undefined, g_heater_pwm_val is undeclared at compile time and generates the appropriate error. I solved by not using g_heater_pwm_val if PIDTEMP is undefined (and therefor undeclared.) Also, the extern declaration was as an int, when g_heater_pwm_val is defined as a volatile unsigned char. This caused a duplicate declaration error, which was solved by changing the declaration in fast_xfer() to match the definition. I didn't dig deeper to try to understand if the mismatch was intentional or test operation other than verify the compile errors no longer occur. | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-28 | Merge pull request #157 from triffid/fix-order | kliment | |
| fix enable_endstops being used before its definition | |||
| 2012-03-28 | fix enable_endstops being used before its definition | Michael Moon | |
| 2012-03-28 | add my name | midopple | |
| 2012-03-27 | Set the defaults for the heart of the sun...uhm, set default board to 33 | Kliment Yanev | |
| 2012-03-27 | Merge pull request #156 from midopple/experimental | kliment | |
| wrong char in configuration.h | |||
| 2012-03-23 | First char '#' was unicode so linux give an compile error | midopple | |
| 2012-03-19 | Merge pull request #155 from midopple/experimental | kliment | |
| Try to merge fixes from Master into Experimental | |||
| 2012-03-19 | Fixes virtual endstops when using mixed physical endstop positions. | midopple | |
| Thanks to ticking | |||
| 2012-03-19 | Merge commit pins.h from master to experimentell | midopple | |
| Conflicts: Sprinter/pins.h | |||
| 2012-03-19 | Merge pull request #154 from midopple/experimental | kliment | |
| AT90USB128x / Speedtable with F_CPU / fix include Closes #145 | |||
| 2012-03-19 | Version 1.3.11T | midopple | |
| - fix for broken include in store_eeprom.cpp --> Thanks to kmeehl (issue #145) - Make fastio & Arduino pin numbering consistent for AT90USB128x. --> Thanks to lincomatic - Select Speedtable with F_CPU - Use same Values for Speedtables as Marlin | |||
| 2012-03-19 | fix for broken include in store_eeprom.cpp | midopple | |
| Thanks to kmeehl | |||
| 2012-03-19 | Make fastio & Arduino pin numbering consistent for AT90USB128x. | midopple | |
| Thanks to lincomatic | |||
| 2012-03-18 | Merge pull request #152 from lincomatic/master | kliment | |
| Make fastio & Teensyduino Pin Numbering consistent with each other for AT90USB128x | |||
| 2012-03-17 | Make fastio & Arduino pin numbering consistent for AT90USB128x | lincomatic | |
| 2012-03-14 | Merge pull request #150 from midopple/experimental | kliment | |
| Fix gen7 support, fix bug in ENDSTOPS_ONLY_FOR_HOMING | |||
| 2012-03-14 | ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared | midopple | |
| New Version V1.3.10T | |||
| 2012-03-13 | Add info to GEN7 Pins | midopple | |
| 2012-03-13 | Merge pull request #4 from metzench/patch-1 | midopple | |
| Update pins.h for gen7 | |||
| 2012-03-13 | Update pins.h for gen7, working setup for 20MHz | Christian Metzen | |
| 2012-03-13 | Info about GEN7 @ 20Mhz | midopple | |
| right Fuses settings for Bootloader | |||
| 2012-03-12 | calculate feedrate without extrude before planner block is set | midopple | |
| 2012-03-10 | New Board --> GEN7 @ 20 Mhz | midopple | |
| Select in configuration.h --> #define MOTHERBOARD 71 New Speedtable for 16 Mhz and 20 Mhz | |||
| 2012-03-05 | Merge pull request #148 from midopple/experimental | kliment | |
| Slowdown Function when Plannerpuffer is low | |||
| 2012-03-04 | Merge commit 'from changwoo/arduino-1.0-compatibility' into experimental | midopple | |
| 2012-03-04 | Merge pull request #147 from changwoo/arduino-1.0-compatibility | kliment | |
| Arduino 1.0 compatibility for experimental | |||
| 2012-03-04 | Move SLOWDOWN Funktion up, at the current position does not work | midopple | |
| 2012-03-05 | Update README on Arduino v1 support | Changwoo Ryu | |
| 2012-03-05 | Correct SD for Arduino 1.0 compatibility | Changwoo Ryu | |
| With Arduino 1.0 Print class: - write() should return, and - print() with a uint_8 or int_8 character argument does not call print(char) anymore. So character argument should be casted to 'char' explicitly. | |||
| 2012-02-24 | Merge pull request #144 from midopple/experimental | kliment | |
| Fix Comment, Optimize, remove Unused code, fix makefile | |||
| 2012-02-24 | Merge commit '89180de4bfd598298f4d5e77889c57a250e35084' into experimental | midopple | |
| Conflicts: Sprinter/Makefile | |||
| 2012-02-24 | If a line starts with ';', it is ignored but comment_mode is reset. | midopple | |
| A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. --> Tanks to jschleic Same fix for SD Card, testet and work (midopple) | |||
| 2012-02-24 | Version 1.3.07T | midopple | |
| - Optimize Variable Size (faster Code) --> heater.cpp - Remove unused Code from Interrupt --> faster ~ 22 us per step - Replace abs with fabs --> Faster and smaler | |||
| 2012-02-24 | Remove unused function "st_set_position" | midopple | |
| 2012-02-24 | Add "store_eeprom.cpp" to makefile | midopple | |
| 2012-02-24 | fix applet/core.a: not found --> Thanks to triffid | midopple | |
| 2012-02-24 | Changhe PWM Value from INT to unsigned char, is faster for interrupt | midopple | |
| 2012-02-24 | compile experimental using the Makefile | Joachim Schleicher | |
| * add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile | |||
| 2012-02-23 | Merge pull request #142 from jschleic/fix-comment_mode | kliment | |
| fix comment mode. | |||
| 2012-02-23 | Merge pull request #141 from jschleic/fix-Makefile2 | kliment | |
| Fix Makefile in experimental | |||
| 2012-02-23 | fix comment mode. | Joachim Schleicher | |
| Closes #140. If a line starts with ';', it is ignored but comment_mode is reset. A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. Probably a similar fix is necessary for the SDSUPPORT part; I cannot test that part without an SD-shield. | |||
| 2012-02-23 | compile experimental using the Makefile | Joachim Schleicher | |
| * add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile | |||
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |