summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-06-29Merge pull request #196 from kliment/mastermidopple
Thermistortable 7 without thermistor shows 5 C
2012-06-29Thermistortable 7 without thermistor shows 5 C, add an safety point with 0 Cmidopple
2012-06-27Merge pull request #195 from kliment/mastermidopple
merge masterchanges into experimental
2012-06-27Merge pull request #194 from felipesanches/refactor_eeprom2midopple
Refactor eeprom routines
2012-06-27use PID_PGAIN, PID_IGAIN, PID_DGAIN for PID default valuesFelipe Corrêa da Silva Sanches
2012-06-27calculate eeprom parameter addresses based on previous param address plus ↵Felipe Corrêa da Silva Sanches
sizeof(type)
2012-06-27refactor eeprom routines to make it possible to modify the value of a single ↵Felipe Corrêa da Silva Sanches
parameter
2012-06-23Merge pull request #191 from MrAlvinTesting/patch-1kliment
Add ATMega 644P SMD pinout as comment
2012-06-23Update masterMrAlvinTesting
2012-06-18Merge pull request #190 from felipesanches/refactor_homingkliment
Refactor homing
2012-06-18reimplement homing routine as an inline functionFelipe Corrêa da Silva Sanches
2012-06-18refactoring homing routine to avoid copy&pasted codeFelipe Corrêa da Silva Sanches
2012-06-15Merge pull request #188 from felipesanches/experimentalkliment
fix a few typos and english usage
2012-06-15fix a few typos and correct english usageFelipe Corrêa da Silva Sanches
2012-06-14Merge pull request #186 from blddk/experimentalmidopple
Extruder cooling fan
2012-06-14Forgot to pit the part in where it makes the pin an output pin... >.<blddk
2012-06-12Merge pull request #185 from tzikis/experimentalkliment
Patched the pins.h file to accept more Sanguino versions
2012-06-12changed the pins.h file to accept more Sanguino versionsVasileios Georgitzikis
2012-06-12Update README to Arduino Version 0023midopple
2012-06-12Version 1.3.19Tmidopple
- Set maximum acceleration. If "steps per unit" is Change the acc were not recalculatet - Extra Parameter for Max Extruder Jerk - New Parameter (max_e_jerk) in EEPROM --> Default settings after update !!
2012-06-11Merge pull request #183 from kliment/mastermidopple
Error with Command M201
2012-06-11Error with Command M201, when this Command is use the same Values are ↵midopple
written to maximum Feedrate.
2012-06-07Merge pull request #182 from blddk/experimentalkliment
Added M400 to synchronize the motion queue
2012-06-07Added M400blddk
2012-06-02Merge pull request #179 from kliment/mastermidopple
Thermistor type 3, disconnecting thermistor yields temp -20, and hotend gets switched to full power
2012-06-02Bug in heater.cpp --> Thermistor type 3, disconnecting thermistor yields ↵midopple
temp -20, and hotend gets switched to full power
2012-05-30repaired thermistortable_6 by graphcial fitting of the off-slope values.midopple
Thanks to bkubicek
2012-05-28Merge pull request #177 from kliment/mastermidopple
Wrong declaration for Variable min_time_before_dir_change
2012-05-28Merge pull request #176 from blddk/experimentalmidopple
Error with DELAY_ENABLE Thanks to blddk
2012-05-27Merge pull request #174 from changwoo/experimental-arduino-1.0-compatibilitykliment
Experimental arduino 1.0 compatibility
2012-05-24Added variables for extruder fanblddk
2012-05-24Added function to turn a fan on and off to keep heat from the hotend to rise ↵blddk
up into the extruder.
2012-05-24Too many if('sblddk
2012-05-24Wrong declaration for Variable min_time_before_dir_change midopple
should be const long
2012-05-21Arduino 1.0 buildChangwoo Ryu
2012-05-17Merge pull request #171 from kliment/mastermidopple
additional dropsegments test
2012-05-16If a small move is drop and the next move is retract the speed is wrong ↵midopple
calculated see https://github.com/kliment/Sprinter/issues/170 thanks to jschleic
2012-05-15Add MOTHERBOARD 51 for GEN6 with Heatbed and Heatbedsensormidopple
2012-05-04Version 1.3.17Tmidopple
- M303 - PID relay autotune possible - G4 Wait until last move is done
2012-05-01Merge pull request #168 from kliment/mastermidopple
Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is
2012-05-01Merge pull request #167 from OhmEye/masterkliment
Fix compile error if SD_FAST_XFER_AKTIV is on and PID is off
2012-04-30Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID isOhmEye
enabled. Fix: If SD_FAST_XFER_AKTIV is defined, fast_xfer() only declares g_heater_pwm_val if PIDTEMP is defined, but later assigns g_heater_pwm_val=0 regardless whether PIDTEMP is defined or not. If PIDTEMP is undefined, g_heater_pwm_val is undeclared at compile time and generates the appropriate error. I solved by not using g_heater_pwm_val if PIDTEMP is undefined (and therefor undeclared.) Also, the extern declaration was as an int, when g_heater_pwm_val is defined as a volatile unsigned char. This caused a duplicate declaration error, which was solved by changing the declaration in fast_xfer() to match the definition. I didn't dig deeper to try to understand if the mismatch was intentional or test operation other than verify the compile errors no longer occur.
2012-04-24Fix commit Textmidopple
2012-04-24Extra Retract Feedrate for Extrudermidopple
- Use extra extruder feedrate limit for reverse moves, and also the first forward move after a reverse
2012-04-24Fix typo in Parameteroutputmidopple
2012-04-23Ignore ":" in comments.midopple
2012-04-22Version 1.3.15Tmidopple
- M206 - set additional homeing offset (Thank to se5a for this idea) (First Version is without saving to EEPROM) - Option for minimum FAN start speed --> #define MINIMUM_FAN_START_SPEED 50 (set it to zero to deaktivate)
2012-04-20When endstop is hit count virtual steps, so the print lose no position when ↵midopple
endstop is hit
2012-04-20- Extrudmultiply with code M221 Sxxx (S100 original Extrude value)midopple
- use Feedratefaktor only when Extruded lenght > 0 - M106 / M107 can drive the FAN with PWM + Port check for not using Timer 1 - New Option --> FAN_SOFT_PWM, with this option the FAN PWM can use every digital I/O (PWM with 500 hz) - Added M93 command. Sends current steps for all axis.
2012-04-02Fixed small bug in arcs when segemnts are zeromidopple
Thanks to hurzl
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-26 05:18:20 +0000