sprinter - Firmware for 3d printer

Age	Commit message (Collapse)	Author
2012-01-22	Added option to set a delay after enabling a stepper driver, default turned ↵	blddk
	off to keep current behavior.
2012-01-22	Added option to set a delay after enabeling stepper driver, to allow the ↵	blddk
	driver to enable (time needed according to datasheet)
2012-01-20	correct dependencies in Makefile	Joachim Schleicher
	applet/$(TARGET).elf should depend on the cpp file, not on .pde so that the cpp is rebuilt when pde changes. We drop the target applet_files to achieve the correct behaviour. Now 'make upload' does rebuild the hex file as well.
2011-12-06	Fix ifdef with missing # in Sprinter.pde and add 644 non P to the Gen 7 ↵	Greg Dahlman
	board in pins.h
2011-12-05	Fixing issues in pins.h and fastio.h, I created them not understanding it ↵	Greg Dahlman
	was using arduino pin numbers I also put in a note that Gen 7 only works at 16 MHZ due to timing issues with WProgram.h and wiring.h
2011-12-04	Added an option to make init.g on SD run on boot.	Nathan Zadoks

2011-11-28	Add gen7 to list of boards in configuration	Kliment Yanev
	Allow ATmega644 (non-P version) for Gen7
2011-11-28	Revert "Merge pull request #121 from Traumflug/master"	Kliment Yanev
	This reverts commit 11d3281a09e2a2f0ae7c9695f79d2d903c22716b, reversing changes made to f8c17d3b4655ba9b694c407ff174135badb914a5.
2011-11-28	pins.h: allow an ATmega644 (without P).	Markus Hitter

2011-11-16	M30/M31 fast sd block transfer	Philip Kin

2011-11-16	M30/M31 fast sd block transfer	Philip Kin

2011-11-10	Merge branch 'master' into experimental	Kliment Yanev

2011-11-10	Improve 200k thermistor table to better match reality	Kliment Yanev

2011-11-06	Merge pull request #116 from cdaringe/master	kliment
	Experimental oscillation reduction
2011-11-06	osc reduction	Chris Dieringer

2011-11-03	Edited pins.h to add missing #endif	Greg Dahlman

2011-11-02	Added Pin 33-40 digital defs to fastio.h for the 644	Greg Dahlman

2011-11-02	Added support for Gen7 Board	Greg Dahlman

2011-10-29	Define default value for alarm pin	Kliment Yanev

2011-10-29	Fix d calculation on XYZ moves where comparison was inside of abs() instead ↵	barclayo
	of comparing with the result.
2011-10-28	Moved pins.h footer to the end of the file, fixing teensylu support	Joe Kerman

2011-10-27	PID parameters for MakerGear	Keegi

2011-10-27	Merge branch 'master' of github.com:kliment/Sprinter into experimental	Kliment Yanev
	Conflicts: Sprinter/Configuration.h
2011-10-16	Update Sprinter/Sprinter.pde	blddk

2011-10-16	Update Sprinter/Sprinter.pde	blddk

2011-10-16	Update Sprinter/Sprinter.pde	blddk

2011-10-16	Update Sprinter/Configuration.h	blddk

2011-10-16	Added options for the controller cooling fan	blddk

2011-10-16	Added function for controlling controller cooling fan	blddk

2011-10-04	i will figure out git eventually	Joe Kerman

2011-10-04	(correct) pin defs for a190usb1286/teensylu	Joe Kerman

2011-10-03	Merge pull request #96 from rotorit/experimental	kliment
	Add gen3+ support for the techzone gen3 remix
2011-10-01	Merge branch 'master' of github.com:kliment/Sprinter into experimental	Kliment Yanev

2011-09-30	pins.h entry for Teensylu	Joe Kerman

2011-09-30	Added fastio.h support for at90usb1286 (for teensylu)	Joe Kerman

2011-09-28	Fix scoping problem (fixes issue #70)	Guillaume Seguin

2011-09-25	added Gen3 PLUS for TechZone Gen3 Remix Motherboard and renaming 21	rotorit

2011-09-25	Edited Sprinter/pins.h via GitHub	rotorit

2011-09-18	Revert "Merge pull request #95 from AxTheB/master"	Kliment Yanev
	This reverts commit a27649c455c4d13385b32d45bf353ab890da052a, reversing changes made to 8fa84ce04eda414886cc5b075d7257e49b6f7f0a.
2011-09-18	Merge pull request #95 from AxTheB/master	kliment
	simplified string-to-number conversions
2011-09-17	Merge pull request #92 from k-eex/PID	kliment
	PID fixes
2011-09-17	line numbers ale long, not int	Václav 'ax' Hůla

2011-09-17	simplified string-to-number conversions	Václav 'ax' Hůla

2011-09-17	Commit 614b60b was missing function signatures and wouldn't compile	Alessandro Ranellucci

2011-09-17	fixed typo, added even more PID improvements (these settings work out of box ↵	Keegi
	for my old hotend, but overshoot badly on MG hotend)
2011-09-17	PID fixes	Keegi

2011-09-17	Reset heater pins after hard resets to avoid keeping them enabled while we ↵	Alessandro Ranellucci
	don't have temperature control anymore
2011-09-17	Merge remote branch 'upstream/experimental' into alarm-pin	Alessandro Ranellucci
	Conflicts: Sprinter/Sprinter.pde
2011-09-17	Signal an optional ALARM_PIN when reaching MAXTEMP	Alessandro Ranellucci
	Alarm signal can be dismissed by hard-resetting the board or by sending a M42 P23 S0 command (where 23 is the ALARM_PIN)
2011-09-17	Initialize LED pin (was stuck after hard resets)	Alessandro Ranellucci