| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-04-02 | Added M93 command. sends current steps for all axis | se5a | |
| 2012-03-30 | Merge pull request #160 from kliment/master | kliment | |
| Command M106 / M107 | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-28 | Merge from experimental, thanks to triffid_hunter | midopple | |
| 2012-03-28 | fix enable_endstops being used before its definition | Michael Moon | |
| 2012-03-27 | Fixed arc offset | midopple | |
| Thanks to Erik van der Zalm | |||
| 2012-03-27 | Set the defaults for the heart of the sun...uhm, set default board to 33 | Kliment Yanev | |
| 2012-03-23 | First char '#' was unicode so linux give an compile error | midopple | |
| 2012-03-19 | Fixes virtual endstops when using mixed physical endstop positions. | midopple | |
| Thanks to ticking | |||
| 2012-03-19 | Merge commit pins.h from master to experimentell | midopple | |
| Conflicts: Sprinter/pins.h | |||
| 2012-03-19 | Version 1.3.11T | midopple | |
| - fix for broken include in store_eeprom.cpp --> Thanks to kmeehl (issue #145) - Make fastio & Arduino pin numbering consistent for AT90USB128x. --> Thanks to lincomatic - Select Speedtable with F_CPU - Use same Values for Speedtables as Marlin | |||
| 2012-03-19 | fix for broken include in store_eeprom.cpp | midopple | |
| Thanks to kmeehl | |||
| 2012-03-19 | Make fastio & Arduino pin numbering consistent for AT90USB128x. | midopple | |
| Thanks to lincomatic | |||
| 2012-03-17 | Make fastio & Arduino pin numbering consistent for AT90USB128x | lincomatic | |
| 2012-03-14 | ENDSTOPS_ONLY_FOR_HOMING Option ignore Endstop always --> fault is cleared | midopple | |
| New Version V1.3.10T | |||
| 2012-03-13 | Add info to GEN7 Pins | midopple | |
| 2012-03-13 | Update pins.h for gen7, working setup for 20MHz | Christian Metzen | |
| 2012-03-12 | calculate feedrate without extrude before planner block is set | midopple | |
| 2012-03-10 | New Board --> GEN7 @ 20 Mhz | midopple | |
| Select in configuration.h --> #define MOTHERBOARD 71 New Speedtable for 16 Mhz and 20 Mhz | |||
| 2012-03-04 | Merge commit 'from changwoo/arduino-1.0-compatibility' into experimental | midopple | |
| 2012-03-04 | Move SLOWDOWN Funktion up, at the current position does not work | midopple | |
| 2012-03-05 | Correct SD for Arduino 1.0 compatibility | Changwoo Ryu | |
| With Arduino 1.0 Print class: - write() should return, and - print() with a uint_8 or int_8 character argument does not call print(char) anymore. So character argument should be casted to 'char' explicitly. | |||
| 2012-02-24 | Merge commit '89180de4bfd598298f4d5e77889c57a250e35084' into experimental | midopple | |
| Conflicts: Sprinter/Makefile | |||
| 2012-02-24 | If a line starts with ';', it is ignored but comment_mode is reset. | midopple | |
| A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. --> Tanks to jschleic Same fix for SD Card, testet and work (midopple) | |||
| 2012-02-24 | Version 1.3.07T | midopple | |
| - Optimize Variable Size (faster Code) --> heater.cpp - Remove unused Code from Interrupt --> faster ~ 22 us per step - Replace abs with fabs --> Faster and smaler | |||
| 2012-02-24 | Remove unused function "st_set_position" | midopple | |
| 2012-02-24 | Add "store_eeprom.cpp" to makefile | midopple | |
| 2012-02-24 | fix applet/core.a: not found --> Thanks to triffid | midopple | |
| 2012-02-24 | Changhe PWM Value from INT to unsigned char, is faster for interrupt | midopple | |
| 2012-02-24 | compile experimental using the Makefile | Joachim Schleicher | |
| * add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile | |||
| 2012-02-23 | fix comment mode. | Joachim Schleicher | |
| Closes #140. If a line starts with ';', it is ignored but comment_mode is reset. A ';' inside a line ignores just the portion following the ';' character. The beginning of the line is still interpreted. Probably a similar fix is necessary for the SDSUPPORT part; I cannot test that part without an SD-shield. | |||
| 2012-02-23 | compile experimental using the Makefile | Joachim Schleicher | |
| * add forward declarations in Sprinter.h * add new files heater.cpp and arc_func.cpp to Makefile | |||
| 2012-02-23 | Thermistortable temptable_4 | midopple | |
| correct declaration: const short temptable_4[NUMTEMPS_4][2] | |||
| 2012-02-22 | fix applet/core.a: not found | Michael Moon | |
| 2012-02-17 | The microcontroller can store settings to EEPROM | midopple | |
| to use the fuction set in configuration.h #define USE_EEPROM_SETTINGS --> Save and recall Settings aktive #define PRINT_EEPROM_SETTING --> Print settings to UART Commands: M500 - stores paramters in EEPROM M501 - reads parameters from EEPROM M502 - reverts to the default M503 - Print Settings | |||
| 2012-02-15 | - changed homing function to not conflict with ↵ | midopple | |
| min_software_endstops/max_software_endstops (thanks rGlory) - Corrected distance calculation. (thanks jv4779) | |||
| 2012-02-15 | Standardvalue MAX Feed Rate for Z-Axis reduced to 2 mm/s some Printers had ↵ | midopple | |
| problems with 4 mm/s | |||
| 2012-02-14 | Changed check in arc_func | midopple | |
| if (millimeters_of_travel == 0.0) => if (millimeters_of_travel < 0.001) (thanks mooselake) | |||
| 2012-02-13 | changed homing function to not conflict with ↵ | Vyacheslav Kononenko | |
| min_software_endstops/max_software_endstops | |||
| 2012-02-06 | Add pin definition for the Printrboard Rev B --> Thaks to lwalkera | midopple | |
| 2012-02-05 | Add pin definition for the Printrboard Rev B | Laine Walker-Avina | |
| 2012-02-05 | - Implement Plannercode from Marlin V1 --> big thanks to Erik | midopple | |
| - Stepper interrupt with Step loops - Stepperfrequenz 30 Khz - New Command * M202 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec * M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 * M205 - advanced settings: minimum travel speed S=while printing T=travel only, X= maximum xy jerk, Z=maximum Z jerk - Remove unused Variables - Check Uart Puffer while circle processing (CMD: G2 / G3) - Fast Xfer Function --> move Text to Flash - Option to deaktivate ARC (G2/G3) function (save flash) - Removed modulo (%) operator, which uses an expensive divide | |||
| 2012-02-02 | Without the PID control for Hotend the tempmonitor use the wrong variable | midopple | |
| 2012-02-02 | Option to deaktivate the arc function | midopple | |
| 2012-02-01 | Check Uart Puffer while circle processing (CMD: G2 / G3) | midopple | |
| 2012-01-29 | Add function to check the UART buffer while arc function is working | midopple | |
| 2012-01-29 | Update Changelog in Mainfile | midopple | |
| 2012-01-29 | Change Motherboard to 3 (standardsettings) | midopple | |
| 2012-01-29 | Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2 | midopple | |
| Conflicts: Sprinter/Configuration.h Sprinter/Sprinter.pde | |||
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |