diff options
| -rw-r--r-- | Sprinter/Configuration.h | 3 | ||||
| -rw-r--r-- | Sprinter/fastio.h | 2 | ||||
| -rw-r--r-- | Sprinter/pins.h | 57 |
3 files changed, 60 insertions, 2 deletions
diff --git a/Sprinter/Configuration.h b/Sprinter/Configuration.h index a3a5d59..71e0b08 100644 --- a/Sprinter/Configuration.h +++ b/Sprinter/Configuration.h @@ -9,7 +9,8 @@ // Gen6 = 5, // Sanguinololu up to 1.1 = 6 // Sanguinololu 1.2 and above = 62 -// Gen Gen3 PLUS for RepRap Motherboard V1.2 = 21 +// Teensylu (at90usb) = 8 +// Gen 3 Plus = 21 // gen 3 Monolithic Electronics = 22 // Gen3 PLUS for TechZone Gen3 Remix Motherboard = 23 #define MOTHERBOARD 3 diff --git a/Sprinter/fastio.h b/Sprinter/fastio.h index 73410cb..6b5572a 100644 --- a/Sprinter/fastio.h +++ b/Sprinter/fastio.h @@ -1904,7 +1904,7 @@ pins #endif -#if defined (__AVR_AT90USB1287__) +#if defined (__AVR_AT90USB1287__) || defined (__AVR_AT90USB1286__) // SPI #define SCK DIO9 #define MISO DIO11 diff --git a/Sprinter/pins.h b/Sprinter/pins.h index e88f650..2160335 100644 --- a/Sprinter/pins.h +++ b/Sprinter/pins.h @@ -694,3 +694,60 @@ const int sensitive_pins[] = {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, E_STEP_PIN, E_DIR_PIN, E_ENABLE_PIN, LED_PIN, PS_ON_PIN, HEATER_0_PIN, HEATER_1_PIN, FAN_PIN, TEMP_0_PIN, TEMP_1_PIN}; #endif + +/**************************************************************************************** +* Teensylu 0.7 pin assingments (ATMEGA90USB) +* Requires the Teensyduino software with Teensy2.0++ selected in arduino IDE! +****************************************************************************************/ +#if MOTHERBOARD == 8 +#define MOTHERBOARD 8 +#define KNOWN_BOARD 1 + + +#define X_STEP_PIN 0 +#define X_DIR_PIN 1 +#define X_ENABLE_PIN 39 +#define X_MIN_PIN 13 +#define X_MAX_PIN -1 + +#define Y_STEP_PIN 2 +#define Y_DIR_PIN 3 +#define Y_ENABLE_PIN 38 +#define Y_MIN_PIN 14 +#define Y_MAX_PIN -1 + +#define Z_STEP_PIN 4 +#define Z_DIR_PIN 5 +#define Z_ENABLE_PIN 23 +#define Z_MIN_PIN 15 +#define Z_MAX_PIN -1 + +#define E_STEP_PIN 6 +#define E_DIR_PIN 7 +#define E_ENABLE_PIN 19 + + + +#define HEATER_0_PIN 21 // Extruder +#define HEATER_1_PIN 20 // Bed +#define FAN_PIN 22 // Fan + +#define TEMP_0_PIN 7 // Extruder +#define TEMP_1_PIN 6 // Bed + +#define SDPOWER -1 +#define SDSS 8 +#define LED_PIN -1 +#define PS_ON_PIN -1 +#define KILL_PIN -1 + +#ifndef SDSUPPORT +// these pins are defined in the SD library if building with SD support + #define SCK_PIN 9 + #define MISO_PIN 11 + #define MOSI_PIN 10 +#endif + +#endif + + |