diff options
Diffstat (limited to 'Tonokip_Firmware/configuration.h')
| -rw-r--r-- | Tonokip_Firmware/configuration.h | 156 |
1 files changed, 0 insertions, 156 deletions
diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h deleted file mode 100644 index 2bd4e6a..0000000 --- a/Tonokip_Firmware/configuration.h +++ /dev/null @@ -1,156 +0,0 @@ -#ifndef PARAMETERS_H -#define PARAMETERS_H - -// NO RS485/EXTRUDER CONTROLLER SUPPORT -// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!! -#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5, Sanguinololu = 6 - -//Comment out to disable SD support -#define SDSUPPORT 1 - -//Min step delay in microseconds. If you are experiencing missing steps, try to raise the delay microseconds, but be aware this -// If you enable this, make sure STEP_DELAY_RATIO is disabled. -#define STEP_DELAY_MICROS 1 - -//Step delay over interval ratio. If you are still experiencing missing steps, try to uncomment the following line, but be aware this -//If you enable this, make sure STEP_DELAY_MICROS is disabled. -//#define STEP_DELAY_RATIO 0.25 - -//Comment this to disable ramp acceleration -#define RAMP_ACCELERATION 1 - -//Uncomment this to enable exponential acceleration -//#define EXP_ACCELERATION 1 - -//Acceleration settings -#ifdef RAMP_ACCELERATION -float min_units_per_second = 35.0; // the minimum feedrate -long max_acceleration_units_per_sq_second = 750; // Max acceleration in mm/s^2 for printing moves -long max_travel_acceleration_units_per_sq_second = 1500; // Max acceleration in mm/s^2 for travel moves -#endif -#ifdef EXP_ACCELERATION -float full_velocity_units = 10; // the units between minimum and G1 move feedrate -float travel_move_full_velocity_units = 10; // used for travel moves -float min_units_per_second = 35.0; // the minimum feedrate -float min_constant_speed_units = 2; // the minimum units of an accelerated move that must be done at constant speed - // Note that if the move is shorter than this value, acceleration won't be perfomed, - // but will be done at the minimum between min_units_per_seconds and move feedrate speeds. -#endif - -// AD595 THERMOCOUPLE SUPPORT UNTESTED... USE WITH CAUTION!!!! - -//PID settings: -//Uncomment the following line to enable PID support. This is untested and could be disastrous. Be careful. -//#define PIDTEMP 1 -#ifdef PIDTEMP -#define PID_MAX 255 // limits current to nozzle -#define PID_INTEGRAL_DRIVE_MAX 220 -#define PID_PGAIN 180 //100 is 1.0 -#define PID_IGAIN 2 //100 is 1.0 -#define PID_DGAIN 100 //100 is 1.0 -#endif - -//How often should the heater check for new temp readings, in milliseconds -#define HEATER_CHECK_INTERVAL 50 -#define BED_CHECK_INTERVAL 5000 - -//Experimental temperature smoothing - only uncomment this if your temp readings are noisy -//#define SMOOTHING 1 -//#define SMOOTHFACTOR 16 //best to use a power of two here - determines how many values are averaged together by the smoothing algorithm - -//Experimental watchdog and minimal temp -//The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature -//If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109 -//#define WATCHPERIOD 5000 //5 seconds -//The minimal temperature defines the temperature below which the heater will not be enabled -//#define MINTEMP - -//Experimental max temp -//When temperature exceeds max temp, your bot will halt. -//This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! -//You should use MINTEMP for thermistor short/failure protection. -//#define MAXTEMP 275 - -// Select one of these only to define how the nozzle temp is read. -#define HEATER_USES_THERMISTOR -//#define HEATER_USES_AD595 -//#define HEATER_USES_MAX6675 - -// Select one of these only to define how the bed temp is read. -#define BED_USES_THERMISTOR -//#define BED_USES_AD595 - -// Calibration formulas -// e_extruded_steps_per_mm = e_feedstock_steps_per_mm * (desired_extrusion_diameter^2 / feedstock_diameter^2) -// new_axis_steps_per_mm = previous_axis_steps_per_mm * (test_distance_instructed/test_distance_traveled) -// units are in millimeters or whatever length unit you prefer: inches,football-fields,parsecs etc - -//Calibration variables -float x_steps_per_unit = 80.376; -float y_steps_per_unit = 80.376; -float z_steps_per_unit = 3200/1.25; -float e_steps_per_unit = 16; -float max_feedrate = 200000; //mmm, acceleration! -float max_z_feedrate = 120; - -//For SAE Prusa mendeel float z_steps_per_unit = should be 3200/1.411 for 5/16-18 rod and 3200/1.058 for 5/16-24 -//float x_steps_per_unit = 10.047; -//float y_steps_per_unit = 10.047; -//float z_steps_per_unit = 833.398; -//float e_steps_per_unit = 0.706; -//float max_feedrate = 3000; - -//For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 -const bool X_ENABLE_ON = 0; -const bool Y_ENABLE_ON = 0; -const bool Z_ENABLE_ON = 0; -const bool E_ENABLE_ON = 0; - -//Disables axis when it's not being used. -const bool DISABLE_X = false; -const bool DISABLE_Y = false; -const bool DISABLE_Z = true; -const bool DISABLE_E = false; - -const bool INVERT_X_DIR = false; -const bool INVERT_Y_DIR = false; -const bool INVERT_Z_DIR = true; -const bool INVERT_E_DIR = false; - -// Sets direction of endstops when homing; 1=MAX, -1=MIN -const int X_HOME_DIR = -1; -const int Y_HOME_DIR = -1; -const int Z_HOME_DIR = -1; - - -//Thermistor settings: - -//Uncomment for 100k thermistor -//#include "ThermistorTable_100k.h" -//#include "BedThermistorTable_100k.h" - -//Uncomment for 200k thermistor -//#include "ThermistorTable_200k.h" -//#include "BedThermistorTable_200k.h" - -//Identical thermistors on heater and bed - use this if you have no heated bed or if the thermistors are the same on both: -#include "ThermistorTable_200k.h" -//#include "ThermistorTable_100k.h" -//#include "ThermistorTable_mendelparts.h" -#define BNUMTEMPS NUMTEMPS -#define bedtemptable temptable - -//Endstop Settings -#define ENDSTOPPULLUPS 1 -const bool ENDSTOPS_INVERTING = false; -const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero. -const bool max_software_endstops = true; //If true, axis won't move to coordinates greater than the defined lengths below. -const int X_MAX_LENGTH = 220; -const int Y_MAX_LENGTH = 220; -const int Z_MAX_LENGTH = 100; - -#define BAUDRATE 115200 - - - -#endif |