1 files changed, 44 insertions, 44 deletions
diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h
index fec610b..50e1c76 100644
--- a/Tonokip_Firmware/configuration.h
+++ b/Tonokip_Firmware/configuration.h
@@ -1,45 +1,45 @@
-#ifndef PARAMETERS_H
-#define PARAMETERS_H
-
-// NO RS485/EXTRUDER CONTROLLER SUPPORT
-// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!!
-#define MOTHERBOARD 4 // ATMEGA168 0, SANGUINO 1, MOTHERBOARD = 2, MEGA 3, ATMEGA328 4
-
-// THERMOCOUPLE SUPPORT UNTESTED... USE WITH CAUTION!!!!
-const bool USE_THERMISTOR = true; //Set to false if using thermocouple
-
-// Calibration formulas
-// e_extruded_steps_per_mm = e_feedstock_steps_per_mm * (desired_extrusion_diameter^2 / feedstock_diameter^2)
-// new_axis_steps_per_mm = previous_axis_steps_per_mm * (test_distance_instructed/test_distance_traveled)
-// units are in millimeters or whatever length unit you prefer: inches,football-fields,parsecs etc
-
-//Calibration variables
-float x_steps_per_unit = 10.047;
-float y_steps_per_unit = 10.047;
-float z_steps_per_unit = 833.398;
-float e_steps_per_unit = 0.706;
-float max_feedrate = 3000;
-
-//For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
-const bool X_ENABLE_ON = 0;
-const bool Y_ENABLE_ON = 0;
-const bool Z_ENABLE_ON = 0;
-const bool E_ENABLE_ON = 0;
-
-//Disables axis when it's not being used.
-const bool DISABLE_X = false;
-const bool DISABLE_Y = false;
-const bool DISABLE_Z = true;
-const bool DISABLE_E = false;
-
-//Endstop Settings
-const bool ENDSTOPS_INVERTING = true;
-const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero.
-const bool max_software_endstops = true;  //If true, axis won't move to coordinates greater than the defined lengths below.
-const int X_MAX_LENGTH = 200;
-const int Y_MAX_LENGTH = 200;
-const int Z_MAX_LENGTH = 120;
-
-#define BAUDRATE 19200
-
+#ifndef PARAMETERS_H
+#define PARAMETERS_H
+
+// NO RS485/EXTRUDER CONTROLLER SUPPORT
+// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!!
+#define MOTHERBOARD 4 // ATMEGA168 0, SANGUINO 1, MOTHERBOARD = 2, MEGA 3, ATMEGA328 4
+
+// THERMOCOUPLE SUPPORT UNTESTED... USE WITH CAUTION!!!!
+const bool USE_THERMISTOR = true; //Set to false if using thermocouple
+
+// Calibration formulas
+// e_extruded_steps_per_mm = e_feedstock_steps_per_mm * (desired_extrusion_diameter^2 / feedstock_diameter^2)
+// new_axis_steps_per_mm = previous_axis_steps_per_mm * (test_distance_instructed/test_distance_traveled)
+// units are in millimeters or whatever length unit you prefer: inches,football-fields,parsecs etc
+
+//Calibration variables
+float x_steps_per_unit = 10.047;
+float y_steps_per_unit = 10.047;
+float z_steps_per_unit = 833.398;
+float e_steps_per_unit = 0.706;
+float max_feedrate = 3000;
+
+//For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+const bool X_ENABLE_ON = 0;
+const bool Y_ENABLE_ON = 0;
+const bool Z_ENABLE_ON = 0;
+const bool E_ENABLE_ON = 0;
+
+//Disables axis when it's not being used.
+const bool DISABLE_X = false;
+const bool DISABLE_Y = false;
+const bool DISABLE_Z = true;
+const bool DISABLE_E = false;
+
+//Endstop Settings
+const bool ENDSTOPS_INVERTING = true;
+const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero.
+const bool max_software_endstops = true;  //If true, axis won't move to coordinates greater than the defined lengths below.
+const int X_MAX_LENGTH = 200;
+const int Y_MAX_LENGTH = 200;
+const int Z_MAX_LENGTH = 120;
+
+#define BAUDRATE 19200
+
 #endif