summaryrefslogtreecommitdiff
path: root/Tonokip_Firmware
diff options
context:
space:
mode:
Diffstat (limited to 'Tonokip_Firmware')
-rw-r--r--Tonokip_Firmware/Tonokip_Firmware.pde1
-rw-r--r--Tonokip_Firmware/configuration.h2
-rw-r--r--Tonokip_Firmware/pins.h43
3 files changed, 45 insertions, 1 deletions
diff --git a/Tonokip_Firmware/Tonokip_Firmware.pde b/Tonokip_Firmware/Tonokip_Firmware.pde
index bb744db..89f8ff7 100644
--- a/Tonokip_Firmware/Tonokip_Firmware.pde
+++ b/Tonokip_Firmware/Tonokip_Firmware.pde
@@ -210,6 +210,7 @@ void setup()
if(E_ENABLE_PIN > -1) pinMode(E_ENABLE_PIN,OUTPUT);
if(HEATER_0_PIN > -1) pinMode(HEATER_0_PIN,OUTPUT);
+ if(HEATER_1_PIN > -1) pinMode(HEATER_1_PIN,OUTPUT);
#ifdef HEATER_USES_MAX6675
digitalWrite(SCK_PIN,0);
diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h
index aba5176..b8e477c 100644
--- a/Tonokip_Firmware/configuration.h
+++ b/Tonokip_Firmware/configuration.h
@@ -3,7 +3,7 @@
// NO RS485/EXTRUDER CONTROLLER SUPPORT
// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!!
-#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5
+#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5, Sanguinololu = 6
//Comment out to disable SD support
#define SDSUPPORT 1
diff --git a/Tonokip_Firmware/pins.h b/Tonokip_Firmware/pins.h
index eb305cb..282961f 100644
--- a/Tonokip_Firmware/pins.h
+++ b/Tonokip_Firmware/pins.h
@@ -358,6 +358,49 @@
#define RX_ENABLE_PIN 13
+/****************************************************************************************
+* Sanguinololu pin assignment
+*
+****************************************************************************************/
+#elif MOTHERBOARD == 6
+#ifndef __AVR_ATmega644P__
+#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
+#endif
+
+#define X_STEP_PIN 15
+#define X_DIR_PIN 21
+#define X_ENABLE_PIN -1
+#define X_MIN_PIN 18
+#define X_MAX_PIN -2 //2
+
+#define Y_STEP_PIN 22
+#define Y_DIR_PIN 23
+#define Y_ENABLE_PIN -1
+#define Y_MIN_PIN 19
+#define Y_MAX_PIN -1 //17
+
+#define Z_STEP_PIN 3
+#define Z_DIR_PIN 2
+#define Z_ENABLE_PIN -1
+#define Z_MIN_PIN 20
+#define Z_MAX_PIN -1 //19
+
+#define E_STEP_PIN 1
+#define E_DIR_PIN 0
+#define E_ENABLE_PIN -1
+
+#define LED_PIN -1
+
+#define FAN_PIN -1 // THIS LINE FOR V1.0
+
+#define PS_ON_PIN -1
+#define KILL_PIN -1
+
+#define HEATER_0_PIN 13 // THIS LINE FOR V1.0 (extruder)
+#define HEATER_1_PIN 14 // THIS LINE FOR V1.0 (bed)
+
+#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
+#define TEMP_1_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#else