| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-07-07 | Added chain of command so hotend wont be turned off before print is done. | blddk | |
| 2012-07-07 | Added chain of command so hotend wont be turned off before the print is ↵ | blddk | |
| finished. | |||
| 2012-06-29 | Merge pull request #196 from kliment/master | midopple | |
| Thermistortable 7 without thermistor shows 5 C | |||
| 2012-06-29 | Thermistortable 7 without thermistor shows 5 C, add an safety point with 0 C | midopple | |
| 2012-06-27 | Merge pull request #195 from kliment/master | midopple | |
| merge masterchanges into experimental | |||
| 2012-06-27 | use PID_PGAIN, PID_IGAIN, PID_DGAIN for PID default values | Felipe Corrêa da Silva Sanches | |
| 2012-06-27 | calculate eeprom parameter addresses based on previous param address plus ↵ | Felipe Corrêa da Silva Sanches | |
| sizeof(type) | |||
| 2012-06-27 | refactor eeprom routines to make it possible to modify the value of a single ↵ | Felipe Corrêa da Silva Sanches | |
| parameter | |||
| 2012-06-23 | Update master | MrAlvinTesting | |
| 2012-06-18 | reimplement homing routine as an inline function | Felipe Corrêa da Silva Sanches | |
| 2012-06-18 | refactoring homing routine to avoid copy&pasted code | Felipe Corrêa da Silva Sanches | |
| 2012-06-15 | fix a few typos and correct english usage | Felipe Corrêa da Silva Sanches | |
| 2012-06-14 | Merge pull request #186 from blddk/experimental | midopple | |
| Extruder cooling fan | |||
| 2012-06-14 | Forgot to pit the part in where it makes the pin an output pin... >.< | blddk | |
| 2012-06-12 | changed the pins.h file to accept more Sanguino versions | Vasileios Georgitzikis | |
| 2012-06-12 | Version 1.3.19T | midopple | |
| - Set maximum acceleration. If "steps per unit" is Change the acc were not recalculatet - Extra Parameter for Max Extruder Jerk - New Parameter (max_e_jerk) in EEPROM --> Default settings after update !! | |||
| 2012-06-11 | Merge pull request #183 from kliment/master | midopple | |
| Error with Command M201 | |||
| 2012-06-11 | Error with Command M201, when this Command is use the same Values are ↵ | midopple | |
| written to maximum Feedrate. | |||
| 2012-06-07 | Merge pull request #182 from blddk/experimental | kliment | |
| Added M400 to synchronize the motion queue | |||
| 2012-06-07 | Added M400 | blddk | |
| 2012-06-02 | Merge pull request #179 from kliment/master | midopple | |
| Thermistor type 3, disconnecting thermistor yields temp -20, and hotend gets switched to full power | |||
| 2012-06-02 | Bug in heater.cpp --> Thermistor type 3, disconnecting thermistor yields ↵ | midopple | |
| temp -20, and hotend gets switched to full power | |||
| 2012-05-30 | repaired thermistortable_6 by graphcial fitting of the off-slope values. | midopple | |
| Thanks to bkubicek | |||
| 2012-05-28 | Merge pull request #177 from kliment/master | midopple | |
| Wrong declaration for Variable min_time_before_dir_change | |||
| 2012-05-28 | Merge pull request #176 from blddk/experimental | midopple | |
| Error with DELAY_ENABLE Thanks to blddk | |||
| 2012-05-24 | Added variables for extruder fan | blddk | |
| 2012-05-24 | Added function to turn a fan on and off to keep heat from the hotend to rise ↵ | blddk | |
| up into the extruder. | |||
| 2012-05-24 | Too many if('s | blddk | |
| 2012-05-24 | Wrong declaration for Variable min_time_before_dir_change | midopple | |
| should be const long | |||
| 2012-05-21 | Arduino 1.0 build | Changwoo Ryu | |
| 2012-05-17 | Merge pull request #171 from kliment/master | midopple | |
| additional dropsegments test | |||
| 2012-05-16 | If a small move is drop and the next move is retract the speed is wrong ↵ | midopple | |
| calculated see https://github.com/kliment/Sprinter/issues/170 thanks to jschleic | |||
| 2012-05-15 | Add MOTHERBOARD 51 for GEN6 with Heatbed and Heatbedsensor | midopple | |
| 2012-05-04 | Version 1.3.17T | midopple | |
| - M303 - PID relay autotune possible - G4 Wait until last move is done | |||
| 2012-05-01 | Merge pull request #168 from kliment/master | midopple | |
| Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | |||
| 2012-04-30 | Bug: turn on SD_FAST_XFER_AKTIV and compilation fails if PID is | OhmEye | |
| enabled. Fix: If SD_FAST_XFER_AKTIV is defined, fast_xfer() only declares g_heater_pwm_val if PIDTEMP is defined, but later assigns g_heater_pwm_val=0 regardless whether PIDTEMP is defined or not. If PIDTEMP is undefined, g_heater_pwm_val is undeclared at compile time and generates the appropriate error. I solved by not using g_heater_pwm_val if PIDTEMP is undefined (and therefor undeclared.) Also, the extern declaration was as an int, when g_heater_pwm_val is defined as a volatile unsigned char. This caused a duplicate declaration error, which was solved by changing the declaration in fast_xfer() to match the definition. I didn't dig deeper to try to understand if the mismatch was intentional or test operation other than verify the compile errors no longer occur. | |||
| 2012-04-24 | Fix commit Text | midopple | |
| 2012-04-24 | Extra Retract Feedrate for Extruder | midopple | |
| - Use extra extruder feedrate limit for reverse moves, and also the first forward move after a reverse | |||
| 2012-04-24 | Fix typo in Parameteroutput | midopple | |
| 2012-04-23 | Ignore ":" in comments. | midopple | |
| 2012-04-22 | Version 1.3.15T | midopple | |
| - M206 - set additional homeing offset (Thank to se5a for this idea) (First Version is without saving to EEPROM) - Option for minimum FAN start speed --> #define MINIMUM_FAN_START_SPEED 50 (set it to zero to deaktivate) | |||
| 2012-04-20 | When endstop is hit count virtual steps, so the print lose no position when ↵ | midopple | |
| endstop is hit | |||
| 2012-04-20 | - Extrudmultiply with code M221 Sxxx (S100 original Extrude value) | midopple | |
| - use Feedratefaktor only when Extruded lenght > 0 - M106 / M107 can drive the FAN with PWM + Port check for not using Timer 1 - New Option --> FAN_SOFT_PWM, with this option the FAN PWM can use every digital I/O (PWM with 500 hz) - Added M93 command. Sends current steps for all axis. | |||
| 2012-04-02 | Fixed small bug in arcs when segemnts are zero | midopple | |
| Thanks to hurzl | |||
| 2012-04-01 | Merge pull request #161 from se5a/master | kliment | |
| Added M93 command - sends current steps per unit for all axis | |||
| 2012-04-02 | Added M93 command. sends current steps for all axis | se5a | |
| 2012-03-30 | Merge pull request #160 from kliment/master | kliment | |
| Command M106 / M107 | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-30 | Command M106 / M107 for control the fan can use PWM | midopple | |
| New function to check the used PWM pins | |||
| 2012-03-28 | Merge from experimental, thanks to triffid_hunter | midopple | |
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |