Rename to Sprinter

1 files changed, 0 insertions, 158 deletions

diff --git a/Tonokip_Firmware/configuration.h b/Tonokip_Firmware/configuration.h
deleted file mode 100644
index 0a38a6a..0000000
--- a/Tonokip_Firmware/configuration.h
+++ /dev/null
@@ -1,158 +0,0 @@
-#ifndef PARAMETERS_H
-#define PARAMETERS_H
-
-// NO RS485/EXTRUDER CONTROLLER SUPPORT
-// PLEASE VERIFY PIN ASSIGNMENTS FOR YOUR CONFIGURATION!!!!!!!
-#define MOTHERBOARD 3 // ATMEGA168 = 0, SANGUINO = 1, MOTHERBOARD = 2, MEGA/RAMPS = 3, ATMEGA328 = 4, Gen6 = 5, Sanguinololu = 6
-
-//Comment out to disable SD support
-#define SDSUPPORT 1
-
-//Min step delay in microseconds. If you are experiencing missing steps, try to raise the delay microseconds, but be aware this
-// If you enable this, make sure STEP_DELAY_RATIO is disabled.
-//#define STEP_DELAY_MICROS 1
-
-//Step delay over interval ratio. If you are still experiencing missing steps, try to uncomment the following line, but be aware this
-//If you enable this, make sure STEP_DELAY_MICROS is disabled.
-//#define STEP_DELAY_RATIO 0.25
-
-//Comment this to disable ramp acceleration
-#define RAMP_ACCELERATION 1
-
-//Acceleration settings
-#ifdef RAMP_ACCELERATION
-//X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
-float max_start_speed_units_per_second[] = {25.0,25.0,0.2,10.0};
-long max_acceleration_units_per_sq_second[] = {1000,1000,50,10000}; // X, Y, Z and E max acceleration in mm/s^2 for printing moves or retracts
-long max_travel_acceleration_units_per_sq_second[] = {500,500,50}; // X, Y, Z max acceleration in mm/s^2 for travel moves
-#endif
-
-// AD595 THERMOCOUPLE SUPPORT UNTESTED... USE WITH CAUTION!!!!
-
-//PID settings:
-//Uncomment the following line to enable PID support. This is untested and could be disastrous. Be careful.
-//#define PIDTEMP 1
-#ifdef PIDTEMP
-#define PID_MAX 255 // limits current to nozzle
-#define PID_INTEGRAL_DRIVE_MAX 220
-#define PID_PGAIN 180 //100 is 1.0
-#define PID_IGAIN 2 //100 is 1.0
-#define PID_DGAIN 100 //100 is 1.0
-#endif
-
-//How often should the heater check for new temp readings, in milliseconds
-#define HEATER_CHECK_INTERVAL 500
-#define BED_CHECK_INTERVAL 5000
-//Comment the following line to enable heat management during acceleration
-#define DISABLE_CHECK_DURING_ACC
-#ifndef DISABLE_CHECK_DURING_ACC
-  //Uncomment the following line to disable heat management during the move
-  //#define DISABLE_CHECK_DURING_MOVE
-#endif
-//Uncomment the following line to disable heat management during travel moves (and extruder-only moves, eg: retracts), strongly recommended if you are missing steps mid print.
-//Probably this should remain commented if are using PID.
-//It also defines the max milliseconds interval after which a travel move is not considered so for the sake of this feature.
-#define DISABLE_CHECK_DURING_TRAVEL 1000
-
-//Experimental temperature smoothing - only uncomment this if your temp readings are noisy
-//#define SMOOTHING 1
-//#define SMOOTHFACTOR 16 //best to use a power of two here - determines how many values are averaged together by the smoothing algorithm
-
-//Experimental watchdog and minimal temp
-//The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
-//If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
-//#define WATCHPERIOD 5000 //5 seconds
-//The minimal temperature defines the temperature below which the heater will not be enabled
-//#define MINTEMP 
-
-//Experimental max temp
-//When temperature exceeds max temp, your bot will halt.
-//This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
-//You should use MINTEMP for thermistor short/failure protection.
-//#define MAXTEMP 275
-
-// Select one of these only to define how the nozzle temp is read.
-#define HEATER_USES_THERMISTOR
-//#define HEATER_USES_AD595
-//#define HEATER_USES_MAX6675
-
-// Select one of these only to define how the bed temp is read.
-#define BED_USES_THERMISTOR
-//#define BED_USES_AD595
-
-// Calibration formulas
-// e_extruded_steps_per_mm = e_feedstock_steps_per_mm * (desired_extrusion_diameter^2 / feedstock_diameter^2)
-// new_axis_steps_per_mm = previous_axis_steps_per_mm * (test_distance_instructed/test_distance_traveled)
-// units are in millimeters or whatever length unit you prefer: inches,football-fields,parsecs etc
-
-//Calibration variables
-const int NUM_AXIS = 4; // The axis order in all axis related arrays is X, Y, Z, E
-bool axis_relative_modes[] = {false, false, false, false};
-float axis_steps_per_unit[] = {80.376,80.376,3200/1.25,16}; // {X steps per unit, Y steps per unit, Z steps per unit, E steps per unit}
-//For SAE Prusa mendeel float z_steps_per_unit = should be 3200/1.411 for 5/16-18 rod and 3200/1.058 for 5/16-24
-//float axis_steps_per_unit[] = {10.047,10.047,833.398,0.706};
-float max_feedrate[] = {200000, 200000, 240, 500000}; //mmm, acceleration!
-
-//For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
-const bool X_ENABLE_ON = 0;
-const bool Y_ENABLE_ON = 0;
-const bool Z_ENABLE_ON = 0;
-const bool E_ENABLE_ON = 0;
-
-//Disables axis when it's not being used.
-const bool DISABLE_X = false;
-const bool DISABLE_Y = false;
-const bool DISABLE_Z = true;
-const bool DISABLE_E = false;
-
-const bool INVERT_X_DIR = false;
-const bool INVERT_Y_DIR = false;
-const bool INVERT_Z_DIR = true;
-const bool INVERT_E_DIR = false;
-
-// Sets direction of endstops when homing; 1=MAX, -1=MIN
-const int X_HOME_DIR = -1;
-const int Y_HOME_DIR = -1;
-const int Z_HOME_DIR = -1;
-
-
-//Thermistor settings:
-
-//Uncomment for 100k thermistor
-//#include "ThermistorTable_100k.h"
-//#include "BedThermistorTable_100k.h"
-
-//Uncomment for 200k thermistor
-//#include "ThermistorTable_200k.h"
-//#include "BedThermistorTable_200k.h"
-
-//Identical thermistors on heater and bed - use this if you have no heated bed or if the thermistors are the same on both:
-#include "ThermistorTable_200k.h"
-//#include "ThermistorTable_100k.h"
-//#include "ThermistorTable_mendelparts.h"
-#define BNUMTEMPS NUMTEMPS
-#define bedtemptable temptable
-
-//Endstop Settings
-#define ENDSTOPPULLUPS 1
-const bool ENDSTOPS_INVERTING = false;
-const bool min_software_endstops = false; //If true, axis won't move to coordinates less than zero.
-const bool max_software_endstops = true;  //If true, axis won't move to coordinates greater than the defined lengths below.
-const int X_MAX_LENGTH = 220;
-const int Y_MAX_LENGTH = 220;
-const int Z_MAX_LENGTH = 100;
-
-#define BAUDRATE 115200
-
-//Uncomment the following line to enable debugging. You can better control debugging below the following line
-//#define DEBUG
-#ifdef DEBUG
-  //#define DEBUG_PREPARE_MOVE //Enable this to debug prepare_move() function
-  //#define DEBUG_BRESENHAM //Enable this to debug the Bresenham algorithm
-  //#define DEBUG_RAMP_ACCELERATION //Enable this to debug all constant acceleration info
-  //#define DEBUG_MOVE_TIME //Enable this to time each move and print the result
-  //#define DEBUG_HEAT_MGMT //Enable this to debug heat management. WARNING, this will cause axes to jitter!
-  //#define DEBUG_DISABLE_CHECK_DURING_TRAVEL //Debug the namesake feature, see above in this file
-#endif
-
-#endif