| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2011-05-11 | Remove extraneous newline | kliment | |
| 2011-05-11 | Added some more intelligent homing logic | Sam Ward | |
| 2011-05-11 | Added G28 homing code. | Sam Ward | |
| Re factored main movement routines | |||
| 2011-05-11 | Merge pull request #14 from sam-ward/master | kliment | |
| Cleaned up some code formatting | |||
| 2011-05-11 | Merge branch 'master' of https://github.com/kliment/Sprinter | Sam Ward | |
| 2011-05-11 | Merge pull request #12 from cakeller98/RAMPS_Versions | kliment | |
| Added a RAMPS version #define in pins.h | |||
| 2011-05-11 | Cleaning up code formatting | Sam Ward | |
| 2011-05-11 | Merge pull request #13 from sam-ward/master | kliment | |
| Moved function definitions into separate .h file for readability. | |||
| 2011-05-11 | Moved function definitions into separate .h file for readability. | Sam Ward | |
| 2011-05-11 | Merge branch 'master' of https://github.com/kliment/Sprinter | Sam Ward | |
| 2011-05-11 | extra CRLF | Sam Ward | |
| 2011-05-11 | Added M201 and M202 to set max acceleration for respectively print and ↵ | Emanuele Caruso | |
| travel moves | |||
| 2011-05-11 | Dramatically decreased GCODE write time to SD | Emanuele Caruso | |
| 2011-05-07 | Cleaned up the MEGA1280 | Christopher Keller | |
| Added a RAMPS version #define in pins.h, so there are two clean/clear sections of pins for the RAMPS versions. Also added the Heater_1_Pin -1 to the RAMPS V1.0 section. | |||
| 2011-05-07 | Merge pull request #11 from cakeller98/M84_Adding_Timeout | kliment | |
| Added M84 Timeout for steppers with M84 Sn | |||
| 2011-05-07 | Added M84 Timeout for steppers: | Christopher Keller | |
| Changed the comment to reflect the updated usage Old functionality remains unchanged M84 disables steppers after finishing previous move. Added functionality: M84 S<seconds> adds an inactivity timeout, after which the steppers will be disabled. If S0, then no timeout (default) | |||
| 2011-05-04 | Fixed deceleration bug for constant acceleration | Emanuele Caruso | |
| 2011-05-04 | Added documentation to constant acceleration parameters | Emanuele Caruso | |
| 2011-05-04 | Added constant acceleration option (aka speed ramp), enabled by default | Emanuele Caruso | |
| 2011-05-04 | Added max z feedrate configuration value, default to 120 mm/min. Solution ↵ | Emanuele Caruso | |
| suggested by cakeller98 | |||
| 2011-05-04 | Made exponential acceleration optional with a #define in configuration.h | Emanuele Caruso | |
| 2011-05-03 | Make sure M190 does nothing if no heated bed present. Fix report format to ↵ | kliment | |
| match repsnapper expectations | |||
| 2011-05-03 | Merge pull request #7 from sam-ward/master. | kliment | |
| Added support for M190 - Wait for heated bed to reach target temp. | |||
| 2011-05-03 | Added support for M190 - Wait for heated bed to reach target temp. | Sam Ward | |
| Amended Gcode descriptions at top of file. | |||
| 2011-05-03 | Merge pull request #4 from ScribbleJ/master. | kliment | |
| Makefile support to enable upload/compile without the Arduino IDE. | |||
| 2011-05-03 | Changed avrdude to use copy included in Arduino and to precisely match ↵ | Christopher Jansen | |
| Arduino Env usage. | |||
| 2011-05-02 | Merge pull request #6 from kludgineer/master. | kliment | |
| Added code for M114, Display current position | |||
| 2011-05-02 | Merge pull request #5 from sam-ward/master. | kliment | |
| Updated M28, M29 codes at top of file | |||
| 2011-05-03 | Minor changes to comments and fix to upload target for arduino 0022 | Christopher Jansen | |
| 2011-05-02 | Edited Tonokip_Firmware/Tonokip_Firmware.pde via GitHub | kludgineer | |
| 2011-05-03 | Added comments for M28, M29 to list of implemented Gcodes | Sam Ward | |
| 2011-05-03 | Added Makefile and declared required functions in .pde to support it working. | Christopher Jansen | |
| Tested on various configs with arduinio-0022. Note you have to edit the first few lines of the Makefile to match your config. | |||
| 2011-05-02 | Fix trailing semicolon in #define | kliment | |
| 2011-05-02 | Merge remote branch 'origin/master' | Emanuele Caruso | |
| 2011-05-01 | Added watchdog aand minimal temp for greater safety in the case of a ↵ | kliment | |
| disconnected thermistor | |||
| 2011-05-01 | Added configuration value for absolute delay microseconds, default to 1. ↵ | Emanuele Caruso | |
| This seems to work better than STEP_DELAY_RATIO and is enabled by default | |||
| 2011-05-01 | Added configuration parameter for delaying steps, STEP_DELAY_RATIO. | Emanuele Caruso | |
| This should be manually enabled in configuration.h if you are experiencing missing steps. Please be aware that enabling it may also prevent your motor from reaching the nominal speed. | |||
| 2011-04-29 | Merged pull request #2 from tommycheng/master. | kliment | |
| Adding support for Sanguinololu v1.0 | |||
| 2011-04-30 | Adding Support for Sanguinololu | Tommy Cheng | |
| 2011-04-28 | Merged pull request #1 from WebSpider/master. | kliment | |
| Basic M115 implementation | |||
| 2011-04-29 | Adding basic capabilities (M115) implementation | Nils | |
| 2011-04-28 | Fix missing { causing compile error | kliment | |
| 2011-04-27 | Merge branch 'master' of git@github.com:kliment/Klimentkip | kliment | |
| 2011-04-27 | Added PWM control to fan pin, added smoothing code for erratic gen6 temp ↵ | kliment | |
| readings | |||
| 2011-04-25 | Merge remote branch 'origin/master' | Emanuele Caruso | |
| 2011-04-25 | Merge remote branch 'origin/master' | Emanuele Caruso | |
| 2011-04-25 | Merge remote branch 'origin/master' | Emanuele Caruso | |
| 2011-04-25 | Added separate acceleration configuration parameter for travel moves | Emanuele Caruso | |
| 2011-04-25 | Added separate acceleration configuration parameter for travel moves | Emanuele Caruso | |
| 2011-04-24 | Restored acceleration configuration values to the previous more conservative ↵ | Emanuele Caruso | |
| defaults | |||
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |