summaryrefslogtreecommitdiff
AgeCommit message (Expand)Author
2011-05-15Remove M86, make kill() shut down motors and heaters, but not stop responding...kliment
2011-05-15Make temperature check interval constant regardless of whether a move is happ...kliment
2011-05-14Added support for endstops at either max or min - no longer supports min only.Christopher Jansen
2011-05-14Make either x steps or y steps remaining shortcut the loopkliment
2011-05-14Inverse the logic in the conditional that determines whether to continuekliment
2011-05-14Fix terrible lockup bug with RAMP accelerationkliment
2011-05-14Merge pull request #20 from MrAlvin/patch-1kliment
2011-05-14Added a few spaces here and there.MrAlvin
2011-05-13Merge pull request #19 from MrAlvin/patch-1kliment
2011-05-13Edited Tonokip_Firmware/Makefile via GitHubMrAlvin
2011-05-13Merge pull request #18 from k-eex/fixkliment
2011-05-13Fix typo in M201/M202 y-acceleration settingKeegi
2011-05-12Merge pull request #17 from WebSpider/masterkliment
2011-05-12Removing MCode for overheat protectionNils
2011-05-12Merge branch 'master' of github.com:kliment/SprinterNils
2011-05-12Adding experimental support for max temperature gueard (M143)Nils
2011-05-12Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-12Merge pull request #15 from sam-ward/masterkliment
2011-05-12Make heater check more frequent during moves, intialize SD faster to avoid co...kliment
2011-05-12Added G28 command description to top of file.Sam Ward
2011-05-12Fixed prepare_move function prototype and inliningSam Ward
2011-05-11Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-11Remove extraneous newlinekliment
2011-05-11Added some more intelligent homing logicSam Ward
2011-05-11Added G28 homing code.Sam Ward
2011-05-11Merge pull request #14 from sam-ward/masterkliment
2011-05-11Merge branch 'master' of https://github.com/kliment/SprinterSam Ward
2011-05-11Merge pull request #12 from cakeller98/RAMPS_Versionskliment
2011-05-11Cleaning up code formattingSam Ward
2011-05-11Merge pull request #13 from sam-ward/masterkliment
2011-05-11Moved function definitions into separate .h file for readability.Sam Ward
2011-05-11Merge branch 'master' of https://github.com/kliment/SprinterSam Ward
2011-05-11extra CRLFSam Ward
2011-05-11Added M201 and M202 to set max acceleration for respectively print and travel...Emanuele Caruso
2011-05-11Dramatically decreased GCODE write time to SDEmanuele Caruso
2011-05-07Cleaned up the MEGA1280Christopher Keller
2011-05-07Merge pull request #11 from cakeller98/M84_Adding_Timeoutkliment
2011-05-07Added M84 Timeout for steppers:Christopher Keller
2011-05-04Fixed deceleration bug for constant accelerationEmanuele Caruso
2011-05-04Added documentation to constant acceleration parametersEmanuele Caruso
2011-05-04Added constant acceleration option (aka speed ramp), enabled by defaultEmanuele Caruso
2011-05-04Added max z feedrate configuration value, default to 120 mm/min. Solution sug...Emanuele Caruso
2011-05-04Made exponential acceleration optional with a #define in configuration.hEmanuele Caruso
2011-05-03Make sure M190 does nothing if no heated bed present. Fix report format to ma...kliment
2011-05-03Merge pull request #7 from sam-ward/master.kliment
2011-05-03Added support for M190 - Wait for heated bed to reach target temp.Sam Ward
2011-05-03Merge pull request #4 from ScribbleJ/master.kliment
2011-05-03Changed avrdude to use copy included in Arduino and to precisely match Arduin...Christopher Jansen
2011-05-02Merge pull request #6 from kludgineer/master.kliment
2011-05-02Merge pull request #5 from sam-ward/master.kliment