summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-05-14Added support for endstops at either max or min - no longer supports min only.Christopher Jansen
2011-05-14Make either x steps or y steps remaining shortcut the loopkliment
2011-05-14Inverse the logic in the conditional that determines whether to continuekliment
2011-05-14Fix terrible lockup bug with RAMP accelerationkliment
Reduce ram usage with smaller buffer line size
2011-05-14Merge pull request #20 from MrAlvin/patch-1kliment
Added a few spaces here and there to improve readability.
2011-05-14Added a few spaces here and there.MrAlvin
2011-05-13Merge pull request #19 from MrAlvin/patch-1kliment
Add config for mega 1280 to the makefile
2011-05-13Edited Tonokip_Firmware/Makefile via GitHubMrAlvin
2011-05-13Merge pull request #18 from k-eex/fixkliment
Fix typo in setting y-acceleration in M201/M202
2011-05-13Fix typo in M201/M202 y-acceleration settingKeegi
2011-05-12Merge pull request #17 from WebSpider/masterkliment
Add a maximum temperature limit after which the heater shuts down.
2011-05-12Removing MCode for overheat protectionNils
2011-05-12Merge branch 'master' of github.com:kliment/SprinterNils
2011-05-12Adding experimental support for max temperature gueard (M143)Nils
2011-05-12Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-12Merge pull request #15 from sam-ward/masterkliment
Added G28 homing code
2011-05-12Make heater check more frequent during moves, intialize SD faster to avoid ↵kliment
confusing repsnapper.
2011-05-12Added G28 command description to top of file.Sam Ward
2011-05-12Fixed prepare_move function prototype and inliningSam Ward
2011-05-11Merge branch 'master' of github.com:kliment/Sprinterkliment
2011-05-11Remove extraneous newlinekliment
2011-05-11Added some more intelligent homing logicSam Ward
2011-05-11Added G28 homing code.Sam Ward
Re factored main movement routines
2011-05-11Merge pull request #14 from sam-ward/masterkliment
Cleaned up some code formatting
2011-05-11Merge branch 'master' of https://github.com/kliment/SprinterSam Ward
2011-05-11Merge pull request #12 from cakeller98/RAMPS_Versionskliment
Added a RAMPS version #define in pins.h
2011-05-11Cleaning up code formattingSam Ward
2011-05-11Merge pull request #13 from sam-ward/masterkliment
Moved function definitions into separate .h file for readability.
2011-05-11Moved function definitions into separate .h file for readability.Sam Ward
2011-05-11Merge branch 'master' of https://github.com/kliment/SprinterSam Ward
2011-05-11extra CRLFSam Ward
2011-05-11Added M201 and M202 to set max acceleration for respectively print and ↵Emanuele Caruso
travel moves
2011-05-11Dramatically decreased GCODE write time to SDEmanuele Caruso
2011-05-07Cleaned up the MEGA1280Christopher Keller
Added a RAMPS version #define in pins.h, so there are two clean/clear sections of pins for the RAMPS versions. Also added the Heater_1_Pin -1 to the RAMPS V1.0 section.
2011-05-07Merge pull request #11 from cakeller98/M84_Adding_Timeoutkliment
Added M84 Timeout for steppers with M84 Sn
2011-05-07Added M84 Timeout for steppers:Christopher Keller
Changed the comment to reflect the updated usage Old functionality remains unchanged M84 disables steppers after finishing previous move. Added functionality: M84 S<seconds> adds an inactivity timeout, after which the steppers will be disabled. If S0, then no timeout (default)
2011-05-04Fixed deceleration bug for constant accelerationEmanuele Caruso
2011-05-04Added documentation to constant acceleration parametersEmanuele Caruso
2011-05-04Added constant acceleration option (aka speed ramp), enabled by defaultEmanuele Caruso
2011-05-04Added max z feedrate configuration value, default to 120 mm/min. Solution ↵Emanuele Caruso
suggested by cakeller98
2011-05-04Made exponential acceleration optional with a #define in configuration.hEmanuele Caruso
2011-05-03Make sure M190 does nothing if no heated bed present. Fix report format to ↵kliment
match repsnapper expectations
2011-05-03Merge pull request #7 from sam-ward/master.kliment
Added support for M190 - Wait for heated bed to reach target temp.
2011-05-03Added support for M190 - Wait for heated bed to reach target temp.Sam Ward
Amended Gcode descriptions at top of file.
2011-05-03Merge pull request #4 from ScribbleJ/master.kliment
Makefile support to enable upload/compile without the Arduino IDE.
2011-05-03Changed avrdude to use copy included in Arduino and to precisely match ↵Christopher Jansen
Arduino Env usage.
2011-05-02Merge pull request #6 from kludgineer/master.kliment
Added code for M114, Display current position
2011-05-02Merge pull request #5 from sam-ward/master.kliment
Updated M28, M29 codes at top of file
2011-05-03Minor changes to comments and fix to upload target for arduino 0022Christopher Jansen
2011-05-02Edited Tonokip_Firmware/Tonokip_Firmware.pde via GitHubkludgineer
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-15 05:23:05 +0000