| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-02-05 | - Implement Plannercode from Marlin V1 --> big thanks to Erik | midopple | |
| - Stepper interrupt with Step loops - Stepperfrequenz 30 Khz - New Command * M202 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec * M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 * M205 - advanced settings: minimum travel speed S=while printing T=travel only, X= maximum xy jerk, Z=maximum Z jerk - Remove unused Variables - Check Uart Puffer while circle processing (CMD: G2 / G3) - Fast Xfer Function --> move Text to Flash - Option to deaktivate ARC (G2/G3) function (save flash) - Removed modulo (%) operator, which uses an expensive divide | |||
| 2012-01-29 | Change Motherboard to 3 (standardsettings) | midopple | |
| 2012-01-29 | Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2 | midopple | |
| Conflicts: Sprinter/Configuration.h Sprinter/Sprinter.pde | |||
| 2012-01-29 | Change configuration.h to original settings | midopple | |
| 2012-01-29 | New Version Sprinter V2 | midopple | |
| - Look Vorward Funktion - - Stepper Control with Timer 1 - SOFT PWM for Extruder heating --> Free Timer 1 - G2 / G3 Command for arc real arc - Baudrate 250 kbaud - M30 Command delete file on SD Card - Text moved to flash to free RAM - M203 Command for Temp debugging | |||
| 2012-01-28 | Update Sprinter/Configuration.h | midopple | |
| 2012-01-22 | Added option to set a delay after enabling a stepper driver, default turned ↵ | blddk | |
| off to keep current behavior. | |||
| 2011-12-05 | Fixing issues in pins.h and fastio.h, I created them not understanding it ↵ | Greg Dahlman | |
| was using arduino pin numbers I also put in a note that Gen 7 only works at 16 MHZ due to timing issues with WProgram.h and wiring.h | |||
| 2011-12-04 | Added an option to make init.g on SD run on boot. | Nathan Zadoks | |
| 2011-11-28 | Add gen7 to list of boards in configuration | Kliment Yanev | |
| Allow ATmega644 (non-P version) for Gen7 | |||
| 2011-11-16 | M30/M31 fast sd block transfer | Philip Kin | |
| 2011-11-06 | osc reduction | Chris Dieringer | |
| 2011-10-27 | PID parameters for MakerGear | Keegi | |
| 2011-10-27 | Merge branch 'master' of github.com:kliment/Sprinter into experimental | Kliment Yanev | |
| Conflicts: Sprinter/Configuration.h | |||
| 2011-10-16 | Update Sprinter/Configuration.h | blddk | |
| 2011-10-16 | Added options for the controller cooling fan | blddk | |
| 2011-10-04 | i will figure out git eventually | Joe Kerman | |
| 2011-10-04 | (correct) pin defs for a190usb1286/teensylu | Joe Kerman | |
| 2011-09-30 | pins.h entry for Teensylu | Joe Kerman | |
| 2011-09-25 | added Gen3 PLUS for TechZone Gen3 Remix Motherboard and renaming 21 | rotorit | |
| 2011-09-17 | fixed typo, added even more PID improvements (these settings work out of box ↵ | Keegi | |
| for my old hotend, but overshoot badly on MG hotend) | |||
| 2011-09-17 | PID fixes | Keegi | |
| 2011-09-08 | Merge branch 'master' of github.com:kliment/Sprinter into experimental | Kliment Yanev | |
| 2011-09-08 | Merge pull request #80 from alexrj/different-endstops | kliment | |
| Change ENDSTOPS_INVERTING to [XYZ]_ENDSTOP_INVERT | |||
| 2011-09-08 | Edited Sprinter/Configuration.h via GitHub | reprapperMC | |
| 2011-08-31 | Merge branch 'master' of github.com:kliment/Sprinter into experimental | Kliment Yanev | |
| 2011-08-26 | Fixed configuration for new [XYZ]_ENDSTOP_INVERT options | Alessandro Ranellucci | |
| 2011-08-26 | Edited Sprinter/Configuration.h via GitHub | lemio | |
| 2011-08-25 | Removed all unnecessary config option values to avoid confusion (one might ↵ | Alessandro Ranellucci | |
| think that setting them to 0 disabled the feature, while it has to be commented instead) | |||
| 2011-08-25 | SMOOTHING had a value (1); however turning it to 0 won't disable the ↵ | Alessandro Ranellucci | |
| feature, so that's just confusing. | |||
| 2011-08-23 | Add EPCOS comment to configuration. | jebba | |
| 2011-08-19 | Edited Sprinter/Configuration.h via GitHub | ParCan | |
| 2011-08-09 | Edited Sprinter/Configuration.h via GitHub | rotorit | |
| 2011-08-09 | added motherboard entry for Gen3-pluss and Gen3-Monolithic Electronics | rotorit | |
| 2011-07-26 | Merge pull request #62 from alexrj/heater-current-limit | kliment | |
| Heater current limit | |||
| 2011-07-26 | New config option HEATER_CURRENT to limit current to the nozzle | Alessandro Ranellucci | |
| 2011-07-26 | New implementation of TEMP_RESIDENCY_TIME. We now wait for the target temp ↵ | Alessandro Ranellucci | |
| to be esablished and maintained for residency time +/- a configurable hysteresis | |||
| 2011-07-25 | Merge pull request #60 from LawrenceLeung/master | kliment | |
| Support TEMP_RESIDENCY_TIME. | |||
| 2011-07-25 | Comment out TEMP_RESIDENCY_TIME | Lawrence | |
| 2011-07-25 | Revert "Disable TEMP_RESIDENCY_TIME for default" | Lawrence | |
| This reverts commit eb1c87fa7bf2e4bcc8b074775d88a6e767de2c29. | |||
| 2011-07-25 | Disable TEMP_RESIDENCY_TIME for default | Lawrence Leung larryleungcal@yahoo.com | |
| 2011-07-25 | add support for TEMP_RESIDENCY_TIME for M109 | Lawrence Leung larryleungcal@yahoo.com | |
| 2011-07-24 | Added MakerGear Hybrid Prusa steps per unit values. | Spencer Renosis | |
| 2011-07-24 | added uuid identification support | jglauche | |
| 2011-07-17 | Add some explanations to config, change some variables to #defines. Fixes #36 | kliment | |
| 2011-07-17 | Add extra config for homing feedrate - fixes #28 | kliment | |
| 2011-07-12 | Add 10k thermistor | kliment | |
| 2011-07-07 | Add missing accel per sq second for E | kliment | |
| 2011-07-06 | Put some notes in for gen6 users.. | Ahmet Cem TURAN | |
| 2011-07-06 | Documentation improvements in Configuration.h | kliment | |
 |
index : sprinter | |
| Firmware for 3d printer | sublab |
| summaryrefslogtreecommitdiff |